y156 Rear tyres 80 mm glued onto white rims with 24 mm hexagon, 1 pair

To celebrate the 30th anniversary of the legendary Marder 1/6 scale 2WD buggy, FG Modellsport/T2M releases a special edition, limited to 300 numbered pieces, with the original signature of Franz Gröschl on the sticker sheet as well as a top equipment (G260RC Zenoah engine, hi-capacity low friction aluminum shock absorbers and special aluminum engine mounts). with original 260 Zenoah with Low-Friction Alu shocks with alloy enginemount The Models is built on a 4 mm u-bended chassis. All borings of the lower side are countersunk, therefore the screw heads can't bear out.Double wishbones at font and rear axle as well as 4 bulk oil-pressure shock absorbers guarantee perfect ground adherence. All rotating parts are supported by ball-bearings. Rear gear wheels, differential gears and all driving elements are case-hardened. The side guards protect the model from dirt. With original signature of Franz Gröschl. The model is equipped with a powerfull 26 ccm engine which runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 liters enables you to drive about 45 minutes. The engine can be started without difficulties through the integrated pull-start. To complete the models all merchantable servos and radio control systems are suitable.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery

You can select the tyre hardness above:  - Hurrax HX100 extreme Grip Medium 175/70 mm tyre and  - Hurrax HX400 extreme Grip Soft 175/70 mm tyre HURRAX extreme is one of the most successful tire in large scale off-road racing and specifically designed for astro turf and solid ground. With more than 700 (!) differently designed, closely spaced lugs and the 70 mm wide tread it is reasonably wear resistant and provides optimal grip with good side traction. If this - i.e. on the front axle - is not desired, you may cut the lugs at the tires outer edge to reduce cornering grip. This can be easily done with a small side cutter or strong nail scissors. In order to reduce the edging in the tire on the front axle.This makes a tire less aggressive during cornering and changes the cars behavior towards understeer. It becomes depending on the track conditions (i.e. wet!) a lot more drivable.An optimal vehicle setup can often be achieved by running already used HURRAX extreme tires on the front and new ones on the rear axle.This is especially true for 2WD models. Dimensions:External diameter approx. 175 mmInner diameter approx. 130 mmWidth approx. 70 mmWeight: one glued tire on Hurrax rim: 470 gramsDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. GRP off-road disc rim for tires with approx, 132 mm inner diameter.The closed disc rim features reinforcement ribs on the backside and a protective collar around the wheel nut seat.Dimensions:for tires with an inner diameter of approx. 132 mm and approx. 70 mm widthand an outer diameter of approx. 180 mm (like i.e. GRP / Gandini tires)Weight approx. 172 gramms

MadMax MAXI PIN tyres have been specially developed for carpet race tracks!  The special block tread pattern, with 480 knobs per tyre, provides excellent grip, but also puts extreme strain on the tyre and the rim. The 3-piece Super Star rims from HPI ensure that the tyre fits perfectly on the rim. This means that no adhesive is required to fix the tyre in place and the rim can be used again and again with new tyres. To stabilise the tyre, the outside of the tyre shoulder is equipped with vertical ribbing on the side, which minimises tilting under load and counteracts the shear forces that occur in bends. Furthermore, the MAXI PIN tyres have knobs positioned on the side of the outer side, which particularly support the steering behaviour of your RC car in bends. Taken together, the MAXI PIN tyres provide maximum grip. The set comes with inserts and orange rim rings, including screws.  On request, we can fit the tyres for an additional charge; see the options above.  Dimensions tyres :  - Outer diameter: 185 mm  - Tyre width at the outer edge of the tread: 75 mm Dimensions rims :- Outer diameter: 120 mm- with: 60 mm 1 pair - Outer diameter: 185 mm  - Tyre width at the outer edge of the tread: 75 mm  1 pair

Off-road tires for sandy underground! Gives great results on those carpets which are typical for some off-road tracks. 462 grippy square studs per tire, a total of more then 1800 for a complete set of tires, guarantee maximum traction! The lower profile of the outer stud rows reduces lateral traction and guarantee exceptional directional stability! Therefore the car is less prone to undesirable side rolls! The rim is the 6-spoke design with a steel reinforcement ring around the wheel drive. The NARROW-GRIP tires are available  with 24mm hex for Losi, HPI Baja 5 and Carson GP Wild Attack series cars and they allready glued!To prevent premature wheel drive wear the fit to the rim is very tight. Therefore the rim should be properly aligned with hex drive and completely mounted via tightening the wheel nut! Dimensions:Outer tire diameter: 175 mmTire and rim width: 62 mmRim inner diameter: 119 mmWeight for one tire: 375 grams / for a pair: 750 gramshe manufacturer of the Narrow-Grip 462 indicates that the use of these tires on very heavy models, like the Losi 5ive-T under heavy conditions, such as jumps and shifting / tilting of the chassis, may lead to breakage of spokes or hex socket. Due to this notice that kind of failure will not be compensated. We apologize for this note!As an alternative, we recommend our special offer for the Losi 5ive-T OEM tires and in particular all tire combinations with MadMax EXTREME rims or for Losi and HPI models: y1406/01 - Big Digger y1407/01 - Cross Bond y1408/01- Over Lander y1409/01 - Giant Grip y1417/01 - Ultra Grip Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (24 mm hex for Losi and HPI Baja 5 Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. Wheels drives:18 mm square for FG & co.24 mm hex for Losi, HPI Baja 5 cars.Contents:2 pieces / 1 pair

Astro Grip Tyres Soft on black Hurrax rims with 24mm hex glued, sold as used but in mint condition. See photos for condition and scope of delivery. The MCD Astro-Grip is one of the most popular tyres for big-scale off-road racing. Specially designed for artificial turf and firm ground. Provides optimum grip and low wear. The reinforced tyre shoulder protects the tyre from damage. The vertical ribbing should normally be used on the outside of the tyre and also protects against damage. The ribbing also ensures that the tyre builds up slightly more grip on the outer edge of the tyre on this side due to its higher strength.  Dimensions:  Outer diameter: approx. 180 mm  Inner diameter: approx. 130 mm  Width: approx. 65 mm Content: 2 pairs

Item N° 66292 FG Alloy shock absorber 08 long, 4 mm - 2 pcs.Oil-pressure shock absorber Ø20mm, long version, upper damper mount 4 mm, spring adjustment ring, spring plate, various lower damper mounts. Suitable for the front axle of Off-Road Buggy 4WD, for the rear axle of Off-Road Buggy and Monster models 2WD.