Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

y1387 SPEED TEC replacement fan wheel for SV012 ignition

Product information "y1387 SPEED TEC replacement fan wheel for SV012 ignition"

Genuine Speed-Tec spare/option part.

Contents:
  • 1 piece

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Similar products

Average rating of 0 out of 5 stars

y0811 After-Run, performance enhancing preservation for all 1/5 and 1/6th scale models, 20 ml
Genuine HT spare/option part. After-Run is a performance enhancing preservation, which ensures that the engine starts properly, even after a long time (winter break) storage. Added to the fuel it keeps the fuel system clean.Among other After-Run conserves the diaphragm of the Walbro carburetor!For long term storage (i.e. during winter!) "vital" for the carburetor diaphragms!For 23 to 32 cm³ engines like Zenoah, Chung Yang, PT, Losi, HPI a.s.o.It binds water in the fuel, particularly important when the engine is not run regularly or after wet races. After-Run improves engine performance, ensures better combustion, removes debris and residues. Simply add the content of the bottle to 5 litres of fuel.Contents:1 piece / 20 ml

Content: 20 Milliliter (€395.00* / 1000 Milliliter)

€7.90*

Average rating of 0 out of 5 stars

GPM Air filter cover, no. BJAFCO, 1 pce.
GPM air filter cover which fits easily over your existing air filter. A rubber band at the bottom holds the cover in place. Maintenance of the main filter will be significantly reduced, especially in very dusty environments. Fits all common filters, foam or fabric (K&N) style.

€13.30*

Average rating of 0 out of 5 stars

GPM Starter cover, no. BJPSCO
Keeps cool air coming to your engine by keeping dirt and grass from clogging up the pull starter area. Easily wipe off anything not deflected away. Installs on the starter cover with hook & loop tape. With metal cable management.If using a FG monster / stadium model an additional hole for the support of the lateral carrier plate has to be cut out.

€25.60*

Average rating of 0 out of 5 stars

y1312 Twin hose bracket
Twin hose bracket for hoses up to 7 mm outer diameter. With 5 mm hole for installation by screw or cable tie.Keeps your car's fuel lines in place. Especially helpfull with tuned pipe layouts running close to the engine.Screws with part number #6726/25 are recommended for installation on the fan cover.

From €14.90*

Average rating of 0 out of 5 stars

y1105 Exhaust port and carburetor intake cover plates, for most usual 23cc - 30cc engines
Exhaust port and carburetor intake cover plates, made of 1 mm aluminum, fits most current 23cc - 30cc rc-car engines.Exhaust port cover:Total: approx. 20 x 45 mmMounting holes (ctr./ctr.): approx. 34 mm carb intake cover:Total: ellipse approx. 28 x 40 mmMounting holes (ctr./ctr.): approx. 31 mm

€4.90*

Average rating of 0 out of 5 stars

6061 Mielke pull starter with hybrid starter function
Genuine Mielke spare / option part.Starting by pull starter or by cordless screwdriver or electric starter is possible.Pull starter with hybrid starter function. Who does not know it? A torn starter rope, blisters on your finger from constant pulling or a defective starter pawl. All these problems are a thing of the past with the hybrid starter.With the help of a cordless screwdriver the engine can be started very easily and if the battery of the cordless screwdriver is empty, the engine can be started by using the conventional way with the pull-rope starter.Please note:The starter shaft for electric start is inserted in a straight line in extension of the crankshaft. No part of the vehicle must be in the way here. On a model with a longitudinally mounted engine (e.g. Losi 5ive or DBXL vehicles) the rear axle will usually prevent the use of the electric start. The normal pull start by cable remains possible.Contents:1 piece

€114.90*

Average rating of 0 out of 5 stars

y1430 Spark plug tester for 1/5 & 1/6 cars
The spark plug tester wiil be put in line between the spark plug in the engine and the spark plug cap. When the spark plug is in good working order, pulling the recoil starter will produce a spark easily visible in the clear section of the tester (see video!).

€14.90*

Average rating of 0 out of 5 stars

y0518 Hobbythek service bag
Genuine HT spare/option part. Special fabric bag to protect engines, rc-plates or other expensive items. Large opening and pull-string closure.Size:Diameter 200 mmHeight 200 mmContents:1 pieceAccessories not included.

€7.90*

Average rating of 0 out of 5 stars

y0040 KENT hose quick couplings for all 1/5 & 1/6 cars
y0040 Variant: y0040 Coupling member A and B
The secure hose connection for engine or tank removal! Advantages of the Kent system quick couplings: A safe opening and closing with one hand, as soon as one side is fixed. The design of the "shut-off" valve is a double chamber system, which closes when disconnecting the coupling. (This design enables easy and safe opening of the quick couplings, even under high pressure. Similarly, just as in low pressure applications.) You feel a snap when connecting the couplings, preventing over-tightening or accidental opening. The actions of opening and closing the quick couplings are identical, so that the handling is extremely simple. An ergonomic design guarantees easy handling, yet the space requirement for the couplings is low. Long and safe life of the couplings even with frequent connection and disconnection. In order to protect the fully encapsulated KENT quick coupling system against dirt even after dismantling, sealing the ends with the corresponding white plugs and caps is recommended.

€16.90*

Average rating of 0 out of 5 stars

TT1031 TopTuning Carburetor heat sink for all Zenoah/CY/HPI/Losi and PT (Smartech!) engines
Original TopTuning spare/option part. Carburetor heat sink for all Zenoah/CY/HPI/Losi and PT-Smartech/Carson engines.Fits all Walbro 603/813/990/771/527/1107 carburetors as well as all Smartech/Carson PT engine carburetors and many more!The TopTuning carburetor heat sink counteracts the notorious vapor lock at high engine temperatures.In fact all current large scale engines have a special adaptor for the thermal insulation of the carb (isolator) to keep the carb as cool as possible, so that the fuel does not form bubbles due to heat transfer from the cylinder. And without this isolator the gasoline would literally cook after a short operating time and therefore the engine would receive a leaner mixture. The much feared lean-out until the engine stalls is inevitably.Unfortunately, even a special isolator is often insufficient at higher ambient temperatures or when the engine is subjected to higher loads, e.g. in racing. In such scenarios the better heat dissipation of the Top Tuning carburetor heat sink contributes to the solution of the problem.The easy to install heat sink, requires a considerable manufacturing and milling effort and fits easily to all common 1:5/1:6 large scale cars, such as FG, Mecatech, Smartech/Carson, HPI, Losi, etc..For installation in FG 4WD cars the rear cross member # 66212 must be modified.Attention: the Allen head screw is an imperial size and therefore not compatible with metric Allen wrenches! Available in our options menu Content: Carburetor heat sink 1 x Allen head screw #8-32 x 5/8" (for Walbro carbs) 1 x washer 4 mm

€39.90*

Average rating of 0 out of 5 stars

7323/08 FG Complete pull start unit for CY / Zenoah / Fuelie / Losi engines
fg_7323_08 Zenoah Label: y0481/01 G230RC Zenoah Label+ 3.5EUR
Genuine FG spare/option part. Complete starter unitPull start unit for CY / Zenoah G230/240/260/270/290/320.Contents:1 piece

Variants from €59.90*
€63.40*

Average rating of 0 out of 5 stars

y0045 GPM Crankcase cover for 1/5 & 1/6
To ensure the required cooling for current 1/5 and 1/6 engines the flywheels have fins on both sides. Therefore the fan housing has large openings on the crankcase side for the required air supply. However, the risk of foreign objects (grass, sand, or even stones!) entering here Is very high! As a result, broken fins on the flywheel occur frequently. This leads to reduced cooling efficiency and - even more critical vibrations from a flywheel which is out of balance due to missing fins. Therefore, this kind of flywheel protection is highly recommended, especially for offroad use. The product video explains the handling in detail! Note:It is essential to thoroughly clean and degrease the crankcase prior to attaching the hook-and-loop tape (OKS2661)!For installation on Chung-Yang and Zenoah engines in FG cars, the crankcase cover must be slightly modified in two places where the engine mount is attached (see Figure 6 and 7). Furthermore the fit of the fabric must be as tight as possible in the region of the layshaft pinion (in front of the differential ring gear!) (see Figure 8).Set includes:Special tailored fabric with sewed on hook-and-loop tapehook-and-loop tape for installation to the crankcaseAdhesive for securing the hook-and-loop tape

€24.90*

Customers also viewed

Average rating of 0 out of 5 stars

- GWH04-XM1 GRP W04 REVO XM1 Tyres Soft
This pair of Tyres have the following use indications: GOOD GRIP situation for clean track. GOOD GRIP situation for medium asphalt. GOOD GRIP situation for medium temperatures. This pair of Tyres have the following technical features: REVO treated profile for the maximum traction and the maximum lateral grip. Treated profile studied to maintain the tyre surface alway clean from rubber murble. Compound exclusively developped for model tyres. Inside belt flexible but very strong, vulcanized directly together with tyre compound. Insert foam with special material for high temperatures, for maximum stability and high drive precision. Spoked wheel moulded with special material for high temperatures for maximum grip and stability. Special gluing system 100% guaranteed.The main sizes for this tyre are: WHEEL fixing with square 18mm. TYRE outside diameter 118mm. WHEEL inside diameter 90mm. TYRE tota width 65mm. Note:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability. Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!

€38.90*

Average rating of 0 out of 5 stars

04.04.05 OSKART Brake Pedal
Genuine OSKART Brake Pedal spare/option part.Fits 1/2 scale OSKART.Contents:1 piece

€78.00*
%

Average rating of 0 out of 5 stars

TT1030 Top Tuning CAR-STAND for 1/5, 1/6, 1/8, 1/10
Ideal work stand with extra wide tripod up to 100 kg. load capacity with excellent stability, even on uneven (!) urface.Specially made support mechanism, individually adjustable width from 115 mm to 375 mm for most RC cars from 1/10 to 1/5 scale. incline from 0 to 90° Quickly folded and loaded For easy storage, as well as for transport completely foldable! (Carrying bag available!)Height adjustment of the support from 635 mm to 1000 mm and inclination from 0-90° Length of the support surface 386 mm Bis zu 100Kg belastbar! Support mechanism continuosly adjustable in width Due to various adjustment options, the Top Tuning CAR STAND offers the optimal possibilities for making adjustments or maintenance work on the RC car. The load capacity and stability are beyond doubt with a load limit of 100 kg and the extremely stable tripod. The up to 90 ° adjustable slant shows your RC car at events and presentations, as well as in your assembly room to its best advantage! 6.5 kg. weight Pivoting bracket Height adjustable from 69 to 104 cm Basic frame is made of steel, painted or chromed Car bracket is made of aluminum and stainless steel A tool holder TT1030/01 is also available as an accessory in our shop selection.

€179.90* €199.99* (10.05% saved)

Average rating of 0 out of 5 stars

y0790 SPEED TEC EXPERT Zenoah G230 tuning engine
The SPEED TEC EXPERT genuine Zenoah G230 engine is optimized for performance with sophisticated craftsmanship and guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC EXPERT version modifications: Cylinder: Adjustment of compression; enlarged ports, fuel management milled, modified exhaust and intake. Piston: weight reduced; skirt shortened; oil rings, piston above and below piston ring tapered and piston dome ground. Crankshaft: is adjusted and aligned. Flywheel: weight reduced and checked for runout. Gaskets: use of premium quality gaskets.To achieve the optimum performance gain of a SPEED TEC EXPERT engine, we recommend the use of a tuned pipe ( to the tuned pipes ).

€649.00*

Average rating of 0 out of 5 stars

s23009, Flywheel PT 23/28, 1 pce.
Complete with mounting nut.

€35.95*
Loading...
Upload in progress, please be patient ...
Shopware-Agency Shopware-Agency