y1228 Maxi-Pin 1/6 offroad competition tire, glued, 1 pair

Genuine Smartech spare/option part.

Glossy Zenoah stickers.

The V-pin competition tire is particularly suitable for tracks with loose and sandy surface.The high tread profile, extended to the tire shoulder requires a high manufacturing cost.This tread design guarantees an extremely high side traction and provides maximum propulsion especially on surfaces like sand and loose soil for optimum.A well proven combination is the use of Mammoth tires in the rear and V-pin at the front.By cutting of the tread profile of the V-pin tires you can adjust your car's handling easily. The partly or nearly complete removal of the V-pin tire's tread on the outside of the tire, greatly affects the tire's side bite when cornering. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Please take a look at the corresponding pics:Pic A - very high lateral grip = car tends to oversteerPic B - high lateral grip = still sharp steering responsePic C - reduced lateral grip = neutral handlingPic D - low lateral grip = expect the car to understeerOf course, the before mentioned does depend on the track surface!Summarized: removing tread from V-Pin tires on the front axle will reduce oversteering, calm your car and make it easier to drive.When oversteering is extreme (e.g. high grass) you may even start cutting the tread on the inside shoulder. This can prevent your car from those annoying traction rolls.For very loose soil the soft compound is recommended, under normal condition the medium compound is usually your best choice.Dimensions:Diameter: 163 mmWidth: 65 mmInner diameter: 106 mmPrices of the components:V-Pin tires EUR 39.90 / pairV-Pin tire inserts EUR 9.90 / pairRims FG 3105/02 EUR 14.90 / pairglue set y0067 EUR 13.30Total EUR 78.80Ready mounted and glued EUR 69.90 / pairRim with 18 mm square drive

Extra-wide off-road tyre, suitable for 1/6 FG buggy/truck rims with widening ring! Diameter 165 mm, width 80 mm. Fits FG Leopard large models and HPI Baja with square adapter as well as other makes with 18 mm square rim mount. We have tested with different rubber/tyre compounds over several months on various types of terrain etc. The Mammoth provides top traction, especially on hard and not particularly grippy surfaces, due to its quite strong and large lugs, as well as the extreme width of the tyre! The Mammoth is available in the shore hardnesses soft, medium and hard! The following applies: the harder the surface, the softer the tyre compound should be. Where other tyres erase the ground because they lack grip, the Mammoth provides brutal propulsion. With a few exceptions, the Mammoth will probably only be used on the rear axle. 1 pair

Glued on robust 6-spoke star wheels, with 6 ribbed reinforcement bars.With 18 mm wheel square, suitable for most 1:5 / 1:6 RC cars, FG, Carson, etc.Lane widening with 23 mm countersunk nut and 14 mm deep square drive for most models.450 block sections 3.5 mm thick, provide a good grip, even on hard or slippery surfaces.Due to the high-strength 14 mm tire shoulder, the cornering power of the Rallye-Cross 450 is high, despite the high profile of 3.5 mm, but without provoking a disproportionate overdrive of the model.The large inner diameter of 114 mm the rim, as well as the position of the wheel allows on nearly all models to eventually mount a disc brake at the front, as well as rear wheels. The dimension of the inside edge of the rim to the wheel is 20 mm. The 18 mm, 6-braced wheel square of the Rallye-Cross 450 rim is 8 mm deep.Measures of the Rallye-Cross 450 wheel/rim:Outside diameter: 162 mmProfile width: 62 mmRim inside: 114 mmTire shoulder: 14 mmBlock profile: 3,5 mmAlso suitable for:With the following wheel adapter: y1183 Rim adapterWith the following wheel adapter: y0786 Rim adapter