y0442 HT rim reinforcement all FG-Monster and Stadium rims

Genuine HT spare/option part.Rim reinforcement, transfers the load over a larger diameter into the rim and protects the rim's square. Will also allow for the use of rims with an already damaged square.For FG Off-Road rims 60200, 60201 (wide) and 60205, 60206 (narrow).14 mm wide square drives must be used.Please note:When installed with new (unused) rims, it may be necessary to modify the rim's square slightly.Contents:2 piece

Genuine FG spare/option part.This roll bar is just for looks, not for protection. It consists of aluminum tubes and plastic corner joints.Fits monster truck body shells.Dimensions double loop:Height: approx. 100 mmWide: approx. 230 mmDimensions kickers section:Length: approx. 190 mmWidth: approx. 120 mmContents:1 set

Genuine FG spare/option part. The sides of the Monster Truck tires were reinforced and now we deliver these tires without fabric insert. The advantages are a better lateral traction and more grip.diameter x width: 210 mm x 115 mmThe set includes two tires and two tire inserts.Contents:2 pieces

Narrow Off-Road Buggy tires 65 mm, ready glued on rims. Suitable for all 1:6 Off-Road Buggies. To mount them on FG Off-Road models you need the 18 mm square wheel driver y0067. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing () if necessary is unavoidable.Durchmesser x Breite / diameter x width 180 x 60 mm

The V-pin competition tire is particularly suitable for tracks with loose and sandy surface.The high tread profile, extended to the tire shoulder requires a high manufacturing cost.This tread design guarantees an extremely high side traction and provides maximum propulsion especially on surfaces like sand and loose soil for optimum.A well proven combination is the use of Mammoth tires in the rear and V-pin at the front.By cutting of the tread profile of the V-pin tires you can adjust your car's handling easily. The partly or nearly complete removal of the V-pin tire's tread on the outside of the tire, greatly affects the tire's side bite when cornering. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Please take a look at the corresponding pics:Pic A - very high lateral grip = car tends to oversteerPic B - high lateral grip = still sharp steering responsePic C - reduced lateral grip = neutral handlingPic D - low lateral grip = expect the car to understeerOf course, the before mentioned does depend on the track surface!Summarized: removing tread from V-Pin tires on the front axle will reduce oversteering, calm your car and make it easier to drive.When oversteering is extreme (e.g. high grass) you may even start cutting the tread on the inside shoulder. This can prevent your car from those annoying traction rolls.For very loose soil the soft compound is recommended, under normal condition the medium compound is usually your best choice.Dimensions:Diameter: 163 mmWidth: 65 mmInner diameter: 106 mmPrices of the components:V-Pin tires EUR 39.90 / pairV-Pin tire inserts EUR 9.90 / pairRims FG 3105/02 EUR 14.90 / pairglue set y0067 EUR 13.30Total EUR 78.80Ready mounted and glued EUR 69.90 / pairRim with 18 mm square drive

Genuine HT spare/option part.Rim reinforcement, transfers the load over a larger diameter into the rim and protects the rim's square. Will also allow for the use of rims with an already damaged square.For FG Off-Road rims 6105, 6105/01 (white) and 3105 (silver).14 mm wide square drives must be used.Please note:When installed with new (unused) rims, it may be necessary to modify the rim's square slightly.Contents:2 pieces

Off-Road tires mounted and glued on rims, on chrome rims. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Dimensions:Diameter: 150 mmWidth: 60 mmWheel square: 18 mmContents:4 pieces / 2 pairs