Skip to main content
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

y1016/100-03 Clutch housing Zenoah G320RC for Losi DBXL models

Product information "y1016/100-03 Clutch housing Zenoah G320RC for Losi DBXL models"

Genuine Zenoah G320RC clutch housing.

Modified (milled) clutch housing for installation of a Zenoah G320RC engine in the Desert Buggy XL.

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Customers also bought

Average rating of 0 out of 5 stars

y1016 Zenoah G320RC with Walbro carburetor WT1107
With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.With the new "K & N" version of the Losi DBXL there is another detail, which need to be considered.From the very beginning the hole pattern for the engine installation in the DBXL chassis plate was no precise match to the hole pattern of the engine, even when delivered in stock form with standard engine. Now with the "K&N" version the engine mount has been changed to eliminate this discrepancy. However, all aluminum engine mounts available on the market share their dimensions with the previous plastic engine mount. For the installation of a G320 Zenoah in a "K&N" -DBXL two possible combinations exist in order to obtain the correct hole pattern:When using the standard (new) plastic engine mount a shortened clutch housing is required as in a 5ive-TWhen using an aluminum engine mount a stock length clutch housing is requiredSeparately, it is recommended to enlarge the cutout in the body panel in front of the K & N air filter for about 2 - 3 mm to ensure that the panel cannot chafe on the air filter.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

€314.90*

Average rating of 0 out of 5 stars

AT-DBXL012 ATOP Alloy engine mount for Losi Desert XL+MTXL
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum engine mount for Losi DBXL+MTXL. A much safer seating of the engine and the ability to dissipate heat into the chassis plate are the advantages over the stock plastic engine mount.Contents:1 piece This article is identical to the article in the video!

€22.90*

Average rating of 0 out of 5 stars

903184/01 Clutch block carrier
Genuine Smartech spare/option part.

€6.90*

Average rating of 0 out of 5 stars

903184, Clutch set
Complete clutch with spring, carrier and bolts.Please note:The usual spare parts supply is not yet available for these engines. Therefore the parts may come from disassembled new engines. Since every single engine is tested at the factory, the parts may show some minor signs of "use".

€27.70*

Similar products

Average rating of 0 out of 5 stars

y0305 Colored flexible fuel line, top quality, 1 meter
y0305 Color: y0305/03 - Red
High quality flexible fuel line in your choice of blue, red, yellow, orange and green. Size:Length: approx. 1 meterOuter diameter: approx. 6.3 mmInner diameter: approx. 3.2 mmDiameters are 100% identical to the Zenoah Tygon hose #7352!

€5.90*

Average rating of 0 out of 5 stars

y0141 Inline fuel filter
Genuine HT spare/option part. Fuel filter to be installed in the fuel line outside of the tank. Dimensions of filter body: 32 x 21 x 17 mm.Contents:1 piece

€5.90*
%

Average rating of 0 out of 5 stars

y19302/01 Flywheel and Clutch puller CY, Zenoah, HPI, Losi
Genuine HT spare/option part. Especially for CY / Zenoah G230/240/260/270/290/320, HPI and Losi engines.Can be used for removal of the standard clutch as well!Contents:1 piece

€17.90* €22.90* (21.83% saved)

Average rating of 0 out of 5 stars

GPM Starter cover, no. BJPSCO
Keeps cool air coming to your engine by keeping dirt and grass from clogging up the pull starter area. Easily wipe off anything not deflected away. Installs on the starter cover with hook & loop tape. With metal cable management.If using a FG monster / stadium model an additional hole for the support of the lateral carrier plate has to be cut out.

€25.60*
%

Average rating of 0 out of 5 stars

y0811 After-Run, performance enhancing preservation for all 1/5 and 1/6th scale models, 20 ml
Genuine HT spare/option part. After-Run is a performance enhancing preservation, which ensures that the engine starts properly, even after a long time (winter break) storage. Added to the fuel it keeps the fuel system clean.Among other After-Run conserves the diaphragm of the Walbro carburetor!For long term storage (i.e. during winter!) "vital" for the carburetor diaphragms!For 23 to 32 cm³ engines like Zenoah, Chung Yang, PT, Losi, HPI a.s.o.It binds water in the fuel, particularly important when the engine is not run regularly or after wet races. After-Run improves engine performance, ensures better combustion, removes debris and residues. Simply add the content of the bottle to 5 litres of fuel.Contents:1 piece / 20 ml

Content: 20 Milliliter (€345.00* / 1000 Milliliter)

€6.90* €8.90* (22.47% saved)

Average rating of 0 out of 5 stars

y19302/02 Piston Blocker for almost all engines
Genuine HT spare/option part. Helpful tool for removal of clutch shoes, flywheels and many more.FitsZenoah G230/G240/G260/G270/G290/G320Chung-Yang enginesPT enginesLosi enginesHPI enginesThreadsize:M10 x 1Contents:1 piece

€9.90*

Average rating of 0 out of 5 stars

y0813 Motul 800 Racing Oil
Fully synthetic oil, available in three blends. 1-liter bottle.The optimal 2-stroke oil for 23-30 cm³ engines/cars Motul Racing Oil is available in three different blends: On-Road for high revving onroad cars Off-Road for cars with high torque enginesMixing ratio for 1/5 & 1/6 applications: We recommend a mix with about 4% oil, which means 200 cc of oil to 5 litres of gas (1:25 ratio). With one litre of Motul oil you can mix about 25 litres of optimal fuel for your 1/5 or 1/6 car. That's enough for well over 20 hours of driving fun! Oil / Gas Oil percent Oil per 1 liter of gasoline Oil per 2 liter of gasoline Oil per 3 liter of gasoline Oil per 4 liter of gasoline Oil per 5 liter of gasoline 1:20 5% 50 ml 100 ml 150 ml 200 ml 250 ml 1:25 4% 40 ml 80 ml 120 ml 160 ml 200 ml 1:30 3,33% 33 ml 67 ml 100 ml 134 ml 167 ml 1:33 3% 30 ml 60 ml 90 ml 120 ml 150 ml 1:35 2,86% 29 ml 58 ml 86 ml 115 ml 143 ml 1:40 2,5% 25 ml 50 ml 75 ml 100 ml 125 ml 1:50 2% 20 ml 40 ml 60 ml 80 ml 100 ml

From €24.00*
%

Average rating of 0 out of 5 stars

y1312 Twin hose bracket
Twin hose bracket for hoses up to 7 mm outer diameter. With 5 mm hole for installation by screw or cable tie.Keeps your car's fuel lines in place. Especially helpfull with tuned pipe layouts running close to the engine.Screws with part number #6726/25 are recommended for installation on the fan cover.

From €12.90* €14.90* (13.42% saved)
%

Average rating of 0 out of 5 stars

y0040 KENT hose quick couplings for all 1/5 & 1/6 cars
y0040 Variant: y0040 Coupling member A and B
The secure hose connection for engine or tank removal! Advantages of the Kent system quick couplings: A safe opening and closing with one hand, as soon as one side is fixed. The design of the "shut-off" valve is a double chamber system, which closes when disconnecting the coupling. (This design enables easy and safe opening of the quick couplings, even under high pressure. Similarly, just as in low pressure applications.) You feel a snap when connecting the couplings, preventing over-tightening or accidental opening. The actions of opening and closing the quick couplings are identical, so that the handling is extremely simple. An ergonomic design guarantees easy handling, yet the space requirement for the couplings is low. Long and safe life of the couplings even with frequent connection and disconnection. In order to protect the fully encapsulated KENT quick coupling system against dirt even after dismantling, sealing the ends with the corresponding white plugs and caps is recommended.

€13.90* €16.90* (17.75% saved)

Average rating of 0 out of 5 stars

y1016/100-01 Clutch housing Zenoah G320RC for Losi models
Genuine Zenoah G320RC clutch housing.Modified (milled) clutch housing for installation of a Zenoah G320RC engine in all Losi models.

€49.90*

Average rating of 0 out of 5 stars

y0686 Rapido the gas station for 1/5 and 1/6 cars
6 litre gas can with thumb activated filler valve.With Rapido filling up is quicker, simpler and more convenient than ever! Thanks to the dosing button you can control the flow of fuel precisely.Unlock by folding out!Press the button and keep control of filling!Lock by folding in again. Finished!No spills, no awkward handling, all clean and easy Other:Half round spout for ventilation and visibility suitable also for the smallest tank openingsLarge opening for easy fillingFlow controlled by press-buttonVentilation allows full flowSturdy design with two handlesTransparent 6 litre container with litre indication in the filling and rest positionsContents:1 piece

€59.90*

Average rating of 0 out of 5 stars

y804 HT-flange sealer 518, 50 ml up to 200°C
Especially for installation of all engine gaskets. Temperature resistant from -55 °C to +200 °C. Resistant to water, mineral oils, synthetic lubricants, fuels, organic solvents and refrigerants. info: Hand tight: 10 - 20 minReady to use: 1 - 3 hoursGap fill: 0.5 mmContent: 50 ml Notes for usage: This surface seal is not for use as the sole sealant, it should always be applied in combination with a paper gasket.The HT-surface sealing agent should be sparsely applied over the entire surface, with care being taken that the sealant does not enter the devices internals (e.g. crankcase, differential a.s.o.) during the assembly.

Content: 50 Milliliter (€538.00* / 1000 Milliliter)

€26.90*

Customers also viewed

%

Average rating of 0 out of 5 stars

Walbro carburetor WT603B / WT990 / WT813A / WT1107 / WT1048 / WT668C
7355/08 FG Carburetor type: Walbro WT603BStandard carburetor for Zenoah G230/260. Carb has integrated choke. Typ: Walbro WT603BHowever, we recommend using the WT668C instead of the WT603B.This also has a choke, but the manufacturing quality of the WT668C is better than the WT603B!Optional ball bearing of the throttle shaft can be selected from the shops menu.y1483 Walbro WT-1048 Racing carburetorPopular performance carburetor without choke; with 13.5 mm venturi diameter, especially suitable for large-displacement engines like the Zenoah G320.The stock throttle shaft has been replaced with the proper version required for car applications; including the throttle lever as well.All existing throttle linkages can therefore be connected as usual without modifications.This carburetor does not feature a primer bulb nor a connection for a return line. It is therefore only connected to the supply line from the tank, the return line of the tank has to be closed.Optional ball bearing of the throttle shaft can be selected from the shops menu.y1067 Walbro WT668C carburetorThe Walbro WT668C carburetor fits all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23cc up to over 30cc.The Walbro WT668C features an integrated choke with lever and a throttle shaft linkage lever. Optional ball bearing of the throttle shaft can be selected from the shops menu.Alternative: Walbro 603B also with chokey0251 Performance carburetor with accelerator pump type: WT-813AWalbro WT-813A carb with accelerator pump, improves low end response when the engine is tuned for maximum performance. 15.88mm bore, 12.7mm venturi. Ready for installation with modified shaft already installed. Fits Zenoah G230/240/260/270 engines and their CY/HPI Fuelie clones as well. Optional ball bearing of the throttle shaft can be selected from the shops menu.7855 FG Carburetor type: Walbro WT990Standard carburetor for Zenoah G240, G270 and G290. Typ: Walbro WT990 Optional ball bearing of the throttle shaft can be selected from the shops menu.y1016/051 Carburetor WT1107 G320RCGenuine Zenoah spare/option part. Standard part fits Zenoah G320RC.Optional ball bearing of the throttle shaft can be selected from the shops menu.

€59.90* €79.90* (25.03% saved)

Average rating of 0 out of 5 stars

LOSB5039 Losi Clutch Shoes & Spring, 8,000 RPM. 5T, Mini, DBXL+MTXL
Genuine Losi spare/option part.Fits Losi 5ive-T and 5ive Mini.Contents:1 pieces

€69.99*

Average rating of 0 out of 5 stars

Area-5T-031 Aluminum servo clamps
area_ar_l031 Version: Area-5T-031/02 Aluminum servo clamps
Genuine Area spare/option part.CNC-machined from 6061-T6 aluminum by Area RC. CNC-machined 6061-T6 aluminum servo clamps from Area RC distribute the load from the mounting screws equally over the complete area of the mounting tabs, protecting them against breakage. Available in two versions:0236 for stock servos in Losi 5ive and DBXL, Savöx 235 und 236, Orange Power and other servos with a mounting hole distance of 18 mm5765 für MPX Rhino, Hitec 5765 and other servos with a mounting hole distance of 16 mmContent:2 pieces

€12.90*
Loading...
Upload in progress, please be patient ...
Shopware-Theme Development Shopware-Agency