Elcon 14404, front shock tower for FG Monster Truck 2WD

€79.90*

Product number: 14404

Product information "Elcon 14404, front shock tower for FG Monster Truck 2WD"

CNC-milled aluminum version, suitable for the old version of the FG 2WD monster and stadium models. These vehicles were distinguished by coming from the factory with four shocks each front and rear.

The shock tower comes complete with mounting hardware and four quick-release mounts for the upper shock ends.

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Similar products

y1218 Springs for drive shafts

Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece

€4.90*

y1004 Driveshaft boots for ball drive + dogbones

Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces

€8.90*

y1036 HT rose joints with conical spacers

Genuine HT spare/option part. Dimensions:A = 5 mmB = 6 mmC = 8 mmD = 13 mmContents:2 pieces rose joints4 pieces conical spacers

€18.90*

y6107/02 Wheel squares 18 mm HART-COAT, 17 mm wide

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

€18.95*

y0321 Off-Road tuning springs Dirt-Spring M

federn_dirt_m Version: y0323/06 - M16, black

Progressive tuning springs, will fit the standard red and the thick silver shocks on FG offroad cars. The rear springs will also fit Hurrax shocks. All springs have an internal diameter because of the manufacturing progress: 21 up to 21,5 mm. Available in several versions: For the front on FG 2WD buggies:y0322/01 - M1, 2,1 x 50 mm, yellowy0322/02 - M2, 2,2 x 50 mm, orangey0322/03 - M4, 2,4 x 50 mm, purpley0322/04 - M5, 2,5 x 50 mm, blueFor the rear on FG buggies, front and rear on FG monster cars and 4WD buggies:y0323/01 - M11, 2,1 x 90 mm, yellowy0323/02 - M12, 2,2 x 90 mm, orangey0323/03 - M13, 2,3 x 90 mm, redy0323/04 - M14, 2,4 x 90 mm, purpley0323/05 - M15, 2,5 x 90 mm, bluey0323/06 - M16, 2,6 x 90 mm, blackFor the front on FG buggies:y0324/01 - M01, 2,1 x 60 mm, yellowy0324/02 - M02, 2,2 x 60 mm, orangey0324/03 - M03, 2,3 x 60 mm, redy0324/04 - M04, 2,4 x 60 mm, purpley0324/05 - M05, 2,5 x 60 mm, bluey0323/06 - M16, 2,6 x 90 mm, blackContents:2 pieces

€17.90*

y0578, Alloy front shock tower for FG Sportsline and Off-Road 4WD, 1 pce.

Aluminum front shock tower for FG Off-Road Buggy and Sportsline 4WD, replaces stock plastic part FG #66287.Stock mounting hardware will be re-used.

€59.90*

GPM 66275 Universal drive shaft with ball drive conversion kit for most FG 4WD cars

FG Set price: 163,25 EURFits all FG 4WD cars (except FG Leopard/ TR-4!) Lost drive shafts are a thing of the past! Universal drive shafts allow for higher drive angles than dog bones or ball drives. This makes them a better choice for for wheel-side applications on front axles, where the angles of the steering and suspension meet.GPM universals for ball drive can be disassembled and therefore repaired or rebuilded if necessary. The center pin (No.: 66275/02)of the GPM universal joint is secured by a grub screw, which should be installed using a medium strength screw locking compound (y0114).Therefore the joint can be easily rebuilded by replacing the center pin for cheap and will be good as new again.The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins.The GPM universal drive shaft set includes everything for the conversion of your FG 4WD.Set includes:Quantity:DescriptionPart number2 piecesUniversal drive shaftFG 662752 piecesDifferential ball drive cupGPM 6069/022 piecesDriveshaft booty10046 piecesSteel ballGPM 7080/022 piecesDrive shaft spacer springy1218

€159.90*

Details

y6107/01 Wheel squares 18 mm HART-COAT, 14 mm wide

€17.45*

y0722 Axle plugs for Losi 5ive-T/2.0, Mini

y0722 Quanity: y0722/02 - Set of 10+ 3EUR

For sealing the axles on Losi 5ive-T and Mini cars, keeps debris out of the inner screws which secure the retainer pin. Set of 4 or set of 10 to choice.Can be used for Losi 5ive-T, Mini and HPI Baja cars.

Variants from €3.90*

€6.90*

y2002 Alloy a-arm, front upper FG 4WD/Leopard 2WD

Genuine HT spare/option part.Alloy a-arm front upper for Off-Road Buggy 4WD RTR, Off-Road Beetle 4WD RTR and Monster-/ Stadium- Modelle 4WD RTR, 4WD Porsche and Mini. Replacement for FG item No.: 66266Contents:1 piece

€34.90*

y1309 All steel linkage for steering servo/servo saver application

Genuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece

€27.90*

y6106/07 Wheel square 11,5mm, steel

Two wheel squares with 3mm dowel pins. Like FG 6106/07, but made from heat treated steel. Significantly reduced wear. The pins prevent the squares from damaging the rims under high load. For all FG rims, holes may have to be drilled. Pins should be fitted using high strength thread locking compound.Measures:18 mm square11.5mm wideBore diameter 8 mm

€19.90*

Details

Customers also viewed

HT-Nitrited steel pinions for all FG and 1/5 scale Carson / Smartech C5

Non-standard sizes use two numbers for definition. The second number gives the size of the corresponding ring gear.Attention: not suitable for 1/6 scale Smartech / Carson 2WD Off-Road models. (Link to the Carson Smartech pinions: here)Pinions up to 16T can be used on the layshaft as well.Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.Teeth:Item no.:13 Teeth HT y026814 Teeth FG 604614 to 48 Teeth HT y011615 to 48 Teeth FG 604715 to 48 Teeth HT y19354 wide16 to 48 Teeth FG 643116 to 48 Teeth FG 6431/1 wide17 to 48 Teeth HT y19355-116 to 46 Teeth HT y011917 to 46 Teeth HT y1935518 to 46 Teeth FG 643219 to 46 Teeth HT y1935718 to 44 Teeth HT y012319 to 44 Teeth FG 6432/220 to 44 Teeth FG 643321 to 44 Teeth HT y1935820 to 42 Teeth HT y090421 to 42 Teeth FG 7431/2122 to 42 Teeth FG 743121 to 40 Teeth FG 7432/2122 to 40 Teeth FG 7432/2223 to 40 Teeth FG 7432/2324 to 40 Teeth FG 743225 to 40 Teeth FG 7432/2526 to 40 Teeth HT y1936426 to 38 Teeth FG 7433Contents:1 piece

€29.90*

Configure now

y2004 Tuning aluminum rear suspension set for nearly all FG 4WD Sportsline cars

y2004 Model: y2004/02 - FG 4WD Touring car models (except Porsche GT3 RSR)

Tuning aluminum rear suspension set for nearly all FG 4WD Sportsline cars: Monster-Truck, Off-Road Buggy, Marder, Beetle, Tourenwagen.Does not fit Formula 1, Leopard and Truggy!Assembled units in the pictures are completed with some parts which are not included. These parts will be re-used from the stock suspension when swapping in the aluminum version. You will also need two bags of 6100/04 Turnbuckle left/right M8/40mm.y2004/01 fits:FG 4WD Monster-Truck models and Monster Beetle models, Off-Road, Marder, Beetle, Porsche GT3 RSR and Race Trucks. The only difference between the sets is the length of the lower a-arms (y2004/01 = long, y2004/02 = short). The picture of the assembled set is used for both versions and shows the shorter arms.Part number:Name:y2001Aluminum rear upper a-armsy68401Aluminum rear lower a-arms long66213Aluminum rear shock towery66205/06Aluminum rear diff mountsy2004/02 fits:FG 4WD Touring car models (except Porsche GT3 RSR).Part number:Name:y2001Aluminum rear upper a-armsy68401/01Aluminum rear lower a-arms short66213Aluminum rear shock towery66205/06Aluminum rear diff mountsy2004/03 fits:FG 4WD/2WD Off-Road WB535.Part number:Name:y2001Aluminum rear upper a-armsy68401Aluminum rear lower a-arms long66213/02Aluminum rear shock towery66205/06Aluminium rear diff mounts

€339.90* €379.40* (10.41% saved)

T1257 FG Universal Charger with many adaptor cables

Genuine FG spare/option part. Practical 220V charger, specially designed for RC cars. The TX/PACK CHARGER 2 enables the charging of a 7.2V drive battery or the transmitter battery.Two outputs: 11.6 V 180 mA (transmitter charging plug) and 7.2 V 180 mA (drive battery with Tamiya plug). Only use one output at a time!Contents:1 piece

€27.90*

FG Monster Truck WB535 4WD

Our 4WD models are attractive and very popular. The wheelbase of the WB535 version is 40 mm longer. This modification improved the directional stability as well as further driving qualities significantly. Equipment of the modelAngled 4 mm alloy chassis with countersunk borings at the bottom, 4-wheel belt drive, belt drive cover, differential gear at front and rear axle with hardened bevel gearwheels, closed front axle housing, closed belt drive at the rear, adjustable double wishbones at front and rear axle, all driving parts and gearwheels made of case-hardened steel, adjustable servo saver, 4 adjustable oil-pressure shock absorbers, rear gear brake, alloy side plates, Monster tires with chrome-plated rims, polycarbonate body shell, decal set.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The model is equipped with a original 26 cm³ Chung-Yang (series engine) combustion engine with muffler and ready-for-use oiled filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-starter system the engine can be started without any difficulties.The pictures may display the car with some optional items which are not included, like bed-mounted rollbar, lights, front bumper or mirrors. These items can be added in the drop down menus.The RTR-version is delivered with assembled and preset radio control system and rechargeable batteries. to complete the non-RTR version all popular servos and radio control systems are suitable.Dimension:Length: 780 mmWidth: 510 mmHeight: 350 mmWheelbase: 535 mm

From €1,099.95*

Configure now

67225/03 FG Alloy adjustable key 2° Leopard 2WD/4WD, 2pcs.

Item N° 67225/03 Alloy adjustable key 2° Leopard 2WD/4WD, 2pcs.Spare part for the Leopard 2010 2WD/4WD version

€21.90*

6521 FG Extreme cooler

Genuine FG spare/option part. Contents:1 pieces

€53.90*