FG Stadium Marder 2WD

The legendary 1/6 FG Marder 2WD Off Road Buggy! For many years the ideal entry into the elite class of radio controlled cars! The large-scale car with tough 26 cc engine is operated with normal 2-stroke gas. A 800 cc tank gives almost an hour of driving fun! For the FG Marder theres a wealth of option parts, most of them are not exactly a must, but make infinitely more fun! The FG Marder is also available with completely installed remote control. Just fuel up, start the engine and drive off.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery For an additional charge you can also select the HT-EDITION above. A great tuning offer for your new FG Marder. The standard price for the individual parts is €227.35. These tuning parts not only look great, but they also make your model more reliable.HT-Edition?HT-Edition means: this version comes with a big set of spare / option parts included.Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount bigCNC machined alloy engine mount, direkt replacement for the stock plastic part, heat and tweak resistant. They come with all necessary hardware included.Value: 64,95 EURAlloy spur gear carrierUse for 39T - 44 teeth spur gears.Value: 39,90 EURBall bearing set, sealed, set of 14The seal rings on sealed ball bearings keep dirt and dust out of the bearings. They are therefore particularly suitable for use in dirty and dusty environments.Value: 59,90 EURTotal value: 227,35 EURFeatures:The model is built on an angled 4 mm chassis plate. All screws on the bottom are countersunk with no protruding heads. Double a-arms front and rear axle with 4 high volume oil-filled shock absorbers ensure optimum traction.All rotating parts are supported by ball bearings. Secondary spur gears, bevel gears inside the differential and all drivetrain parts are case-hardened. Rocker panels protect the car against contamination from below. The model is equipped with a powerful 26 cc engine. It needs a regular 2-stroke petrol/oil mix (available at every gas station). The integrated pull starter allows for easy engine starts without additional equipment.Dimensions: Length: 690 mm Width: 420 mm Height: 270 mm Wheelbase: 475 mm

To celebrate the 30th anniversary of the legendary Marder 1/6 scale 2WD buggy, FG Modellsport/T2M releases a special edition, limited to 300 numbered pieces, with the original signature of Franz Gröschl on the sticker sheet as well as a top equipment (G260RC Zenoah engine, hi-capacity low friction aluminum shock absorbers and special aluminum engine mounts). with original 260 Zenoah with Low-Friction Alu shocks with alloy enginemount The Models is built on a 4 mm u-bended chassis. All borings of the lower side are countersunk, therefore the screw heads can't bear out.Double wishbones at font and rear axle as well as 4 bulk oil-pressure shock absorbers guarantee perfect ground adherence. All rotating parts are supported by ball-bearings. Rear gear wheels, differential gears and all driving elements are case-hardened. The side guards protect the model from dirt. With original signature of Franz Gröschl. The model is equipped with a powerfull 26 ccm engine which runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 liters enables you to drive about 45 minutes. The engine can be started without difficulties through the integrated pull-start. To complete the models all merchantable servos and radio control systems are suitable.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery

The legendary 1:6 FG Marder 2WD off-road buggy with extra-wide Mammoth tyres on chrome rims !For many years the ideal entry into the elite class of radio controlled cars! The large-scale car with tough 26 cc engine is operated with normal 2-stroke gas.A 800 cc tank gives almost an hour of driving fun!For the FG Marder theres a wealth of option parts, most of them are not exactly a must, but make infinitely more fun!The FG Marder is also available with completely installed remote control. Just fuel up, start the engine and drive off.You can select the car with complete RTR-equipment from the options menu.RTR-equipmentRTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed.Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-batteryFor an additional charge you can also select the HT-EDITION above. A great tuning offer for your new FG Marder. The standard price for the individual parts is €227.35. These tuning parts not only look great, but they also make your model more reliable.HT-Edition?HT-Edition means: this version comes with a big set of spare / option parts included.Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount bigCNC machined alloy engine mount, direkt replacement for the stock plastic part, heat and tweak resistant. They come with all necessary hardware included.Value: 64,95 EURAlloy spur gear carrierUse for 39T - 44 teeth spur gears.Value: 39,90 EURBall bearing set, sealed, set of 14The seal rings on sealed ball bearings keep dirt and dust out of the bearings. They are therefore particularly suitable for use in dirty and dusty environments.Value: 59,90 EURTotal value: 227,35 EURFeatures:The model is built on an angled 4 mm chassis plate. All screws on the bottom are countersunk with no protruding heads. Double a-arms front and rear axle with 4 high volume oil-filled shock absorbers ensure optimum traction.All rotating parts are supported by ball bearings. Secondary spur gears, bevel gears inside the differential and all drivetrain parts are case-hardened. Rocker panels protect the car against contamination from below. The model is equipped with a powerful 26 cc engine. It needs a regular 2-stroke petrol/oil mix (available at every gas station). The integrated pull starter allows for easy engine starts without additional equipment.Dimensions:Length: 690 mmWidth: 510 mmHeight: 270 mmWheelbase: 475 mm

With complete RTR equipment y1382 Original Maxi-Pin 1/6 offroad competition tire For an additional charge you can also select the HT-EDITION above. A great tuning offer for your new FG Marder. The standard price for the individual parts is €227.35. These tuning parts not only look great, but they also make your model more reliable.HT-Edition?HT-Edition means: this version comes with a big set of spare / option parts included.Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount bigCNC machined alloy engine mount, direkt replacement for the stock plastic part, heat and tweak resistant. They come with all necessary hardware included.Value: 64,95 EURAlloy spur gear carrierUse for 39T - 44 teeth spur gears.Value: 39,90 EURBall bearing set, sealed, set of 14The seal rings on sealed ball bearings keep dirt and dust out of the bearings. They are therefore particularly suitable for use in dirty and dusty environments.Value: 59,90 EURTotal value: 227,35 EURThe legendary 1/6 FG Marder 2WD Off Road Buggy! For many years the ideal entry into the elite class of radio controlled cars! The large-scale car with tough 26 cc engine is operated with normal 2-stroke gas. A 800 cc tank gives almost an hour of driving fun! For the FG Marder theres a wealth of option parts, most of them are not exactly a must, but make infinitely more fun! The FG Marder comes with completely installed remote control. Just fuel up, start the engine and drive off.Features:The model is built on an angled 4 mm chassis plate. All screws on the bottom are countersunk with no protruding heads. Double a-arms front and rear axle with 4 high volume oil-filled shock absorbers ensure optimum traction.All rotating parts are supported by ball bearings. Secondary spur gears, bevel gears inside the differential and all drivetrain parts are case-hardened. Rocker panels protect the car against contamination from below. The model is equipped with a powerful 26 cc engine. It needs a regular 2-stroke petrol/oil mix (available at every gas station). The integrated pull starter allows for easy engine starts without additional equipment.Dimensions: Length: 690 mm Width: 420 mm Height: 270 mm Wheelbase: 475 mm

This stadium truck is the perfect model for the entry into the RC large scale sport. The model is fully assembled and can be equipped with an RC system in our shopping cart selection. It is available with Lexan body shell. Limited Edition tune parts:2x 4492 Alu Querlenker hinten untenPreis: 55,70 EUR1x 4475/01 Rear alloy shock mountPrice: 96,10 EUR1x 6423 Gear protectorPrice: 20,70 EUR1x 6499 Alloy front shock towerPrice: 69,70 EUR4x 18001 Alloy a-armPrice: 131,60 EURBase price Stadium Truck Sportsline829,90 EURSurcharge tuning parts:373,80 EURRegular price Limited Edition:1203,70 EURThe Stadium Truck comes top equipped as standard and also offers numerous choices for additional option parts to increase driving performance.Product details:1/6 scale 2WD Stadium Truck with double wishbone independent suspension. 4 mm metal chassis plate. All holes on the underside are countersunkFuel tank and RC components are protected by the bevelled chassis>Adjustable toe-in/out on the front suspensionAdjustable camber on the rear suspension4 large-volume oil pressure shocks absorbers with adjustable spring tension for a smooth ride. The secondary spur gears, differential gears and all drive parts are case hardenedThe stadium truck comes with a powerful 26cm³ FG 260 internal combustion engine. This requires standard 2-stroke gas/oil mix available at every gas station.With a tank capacity of 0.7 litres, a driving time of approx. 40 minutes is achieved.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery For an additional charge you can also select the HT-EDITION above. A great tuning offer for your new FG Sportsline. The standard price for the individual parts is €227.35. These tuning parts not only look great, but they also make your model more reliable.HT-Edition?HT-Edition means: this version comes with a big set of spare / option parts included.Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount bigCNC machined alloy engine mount, direkt replacement for the stock plastic part, heat and tweak resistant. They come with all necessary hardware included.Value: 64,95 EURAlloy spur gear carrierUse for 39T - 44 teeth spur gears.Value: 39,90 EURBall bearing set, sealed, set of 14The seal rings on sealed ball bearings keep dirt and dust out of the bearings. They are therefore particularly suitable for use in dirty and dusty environments.Value: 59,90 EURTotal value: 227,35 EURDimensionsLength: 730 mmWidth: 510 mmHeight: 360 mmWheelbase: 470 mm

Special offer, set includes 2 x 3S LiPo batteries 5000mAh 50C. Normal price 958 €.Pirate Desert Short Course Truck 1:7 4x4 6S Brushless RTRSpecial features:Painted and decorated polycarbonate body.Pre-installed 4-channel radio control system (2+2) 2.4 GHzFail-safe function (automatic switch-off in the event of radio failure).With deactivatable gyro to stabilize the vehicle on slippery surfacesProtective housing for the receiver.LED strip on the roof.Versatile tires for different surfaces, large diameter (140 mm).Front and rear axle differentials with gears in waterproof housings.Front and rear bumpersAll-wheel drive completely on ball bearingsReinforced drive for 6S LiPo supply.Technical data :Headlights/rear lights, indicator140 mm tires with fabric (space-savingDifferential + central bearing made of aluminumAluminum servo saverSteering servo with metal gears (18 kg)XT-90 battery connectorsBLACK aluminum chassisESC 150 Amp (6S)Reinforced wishbonesCentral aluminum reinforcementMulti-adjustable front and rear shock absorber mountsRear cardan shafts made of treated steelBrushless motor in 4274/2000 kV Adjustable aluminum motor mountQuick attachment of the battery pack with a strap4-wheel independent suspensionFront wishbone suspensionHomokinetic cardan shafts at the front made of steelAluminum wheel nutsDimensions :Length : 770mmWidth : 380mmHeight : 270mmWeight : 7400gWheelbase : 415 mmWheel diameter : 140x50 mmAdditional information :Minimum age : 14 yearsRequired accessories:chargerTransmitter batteries (4)Scope of delivery:Assembled short course model including electronics and 2xLiPo AkkuInstruction manual