44 products found for "y1303"

rc-car-online - Home

y1303 T-connector charging cable 4mm

Charging cord for batteries with T-connector; cable length 300 mm, silicone insulated cable with gold-plated connectors.

€8.90*

y1306 JETI-SBEC 6-42V voltage regulator

The switching voltage regulator SBEC is supposed to act as a current supply for receivers and servos. It makes possible to use a wide range of input voltages from 2S up to 10S Li-XX cells. Setup of the output voltage between 5 and 8V is accomplished by a shorting plug jumper. This means that the SBEC is also prepared for use with new higher voltage HV-servos. This voltage regulator is for use in combination with the Hitec Servo HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP and the special LiPo 14.8V/3,600mAh receiver battery y1304. It utilizes a 4S LiPo battery to deliver full battery voltage to the HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo with and the usual 6 - to 8 volt supply (depending on the servos) to the rest of the rx system. The output voltage is selectable. We install the required connectors to the regulator. The connection to the T/B servo is designed as a direct power supply, so even the current for the T/B servo does not run through the receiver.The regulator has connectors for battery, Receiver and T/B servo. The steering servos plugs directly into receiver and battery. The JR/universal connector on the battery is for the regulator, the BEC connector is for the steering servo power line.Attention: the switch on the voltage regulator does not disconnect the Hitec HS-1000SGT/HS-1005SGT/HS-1100WP's power output stage from the battery, which has a standby drain of about 6 mA. To prevent deep discharge of the battery, the servo must be disconnected from the battery at the end of the day!For your convenience you could install our new electronic high voltage switch y0767 between servo and battery.Wire loom and heat shrink tubing to add a matching connector to the servos power line are included. Data:Size (w/o wires): 60 x 28 x 10 mmWeight: 29 gramsInput voltage (recommended): 7 to 42 V (2S to 10S LiPo)Output voltage (selectable): 5.0 / 5.5 / 6.0 / 7.0 / 8.0 VOutput current: max. 6,2 A continuous / 12 A impulseContents:1 piece

€74.90*

y1307 Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP

Genuine HT spare/option part.This extremely strong servo horn is specifically designed with dimensions for the installation of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high-performance servo in the Losi 5ive-T and Mini for steering application, but it can be used in other cars with this kind of servo.It bolts directly to the servos stock aluminum disk.The lever of this arm is longer than that of the servo saver. This gives you faster actuating speed of the steering.A linkage with a double-sided arm can only be done properly if all corresponding levers are the same length and the linkages run exactly parallel. If this is not the case, the servo and servo saver shaft will try to change the distance to each other with every steering movement . Thus, undesirable constraining forces.For this reason we decided to give preference to the single-sided arm.Scope of delivery:1 x Aluminium servo horn4 x Socket head cap screws 3 x 14 mm1 x Socket head cap screws 4 x 30 mm1 x Self-lockinghexagon nut M44 x Shim ring 3,2Contents:1 piece

€39.90*

y1309 All steel linkage for steering servo/servo saver application

Genuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece

€27.90*

y1203 HS gilmer belt for FG 4WD cars, 1 pce.

Dimensions same as FG 66237.Very high rupture strength and tearing resistance as well as reduced wear make this belt the perfect choicefor race applications where maximum reliability is a must.Fits cars with 490 and 510 mm wheelbase only. Does not fit WB535 cars! For all FG Offroad 4WD models with 490-510mm ( Offroad buggy, monster and stadium) and all FG Sportsline 4WD 510 ( Porsche GT3, Mini and BMW E30 ) leng 635mm, wedth 18mm.

€34.90*

y1603 SPEED TEC CRANK Team-Edition Zenoah G270 Tuning engine

The SPEED TEC CRANK genuine Zenoah engine is optimized for performance by hand with sophisticated craftsmanship and guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC Team Edition version modifications: Cylinder & case:Adjustment of compression; enlarged ports, fuel management milled, machined and polished exhaust, the intake is flow-optimized the case is specially matched with enlarged and flow-optimized cross section towards the ports Cylinder modified for installation of the ignition systemPiston:Transfer port area optimized for flow, weight reduced and the piston-roof is flow-optimized and polishedCrankshaft:is adjusted, aligned and balancedFlywheel and ignition:Latest SPEED TEC CRANK SV ignition system for rc-car race engines with air baffles, a special balanced 62 mm diameter flywheel, modified ignition coil mount and special ignition system allows for the extremely fast revving of the SPEED TEC team edition engine and guarantees a significantly improved performance.The machined and more than 30% lighter than stock CRANK flywheel with fins on both sides contributes to the optimized engine cooling.Gaskets:Premium quality gaskets installed. Cylinder gasket installed using elastic gasket sealer.Isolator:Special matched and raised insulator Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

€949.00*

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

y1330 BMW 320si WTCC 1/5 body shell, painted, 535 wheelbase, white/light blue

Genuine HT spare/option part.Fits 535 mm wheel base, current touring car width. A rear wing is available through the shop's options menu. The body shell comes without decals!Required body mounts:Front section: FG 7020/11 Front bumperRear body mount: FG 7152/01 Rear body supportSide front: FG 7012 Body mountSide rear: FG 7014 Body mountAvailable decal sheets:y1329 - Vehicle decalsy1320/01 - Team decals Posty1329/02 - Team decals Samsungy1329/03 - BMW-Bank decalsy0683 - Jägermeister decalsy3006 - rc-car-online decalsDimensions:Length: 885 mmWidth: 392 mmHeight: 260 mmWheel base: 530 mm

€99.90*

y1033 HT Aluminum front suspension for FG Marder, Beetle, Pajero, Monster Beetle 2WD, set

The sets include:Item N°Name:y1027HT Aluminum a-arm 2WD, front uppery1026HT Aluminum a-arm 2WD, front lower, one-piecey1028HT Aluminum front bulkhead A for 2WDy1030HT Aluminum front bulkhead B for 2WDy1036HT rose joints with conical spacersy1029HT aluminum droop stopsy1032HT Aluminum shock tower Marder 2WDy1031HT Aluminum bulkhead brace for 2WDUnit prices: 391,00 EURThe sets include complete front bulkheads A + B with brace, upper (adjustable) and lower a-arms and shock tower.Please note: the hinge pins are not included, you will use the pins from the stock suspension!Fits FG Marder, Beetle, Pajero and Monster Beetle.

€339.00* €391.00* (13.3% saved)

y1303/09 EC5 connector, male

Genuine HT spare/option part.High quality version, contacts can be inserted into the housing from either side.Contents:1 piece

€3.90*

y1303/20 HXT4 charging cable

Genuine HT spare/option part.Charging cable for batteries with HXT4 connector, length approx. 37 cm, silicone insulated cable with gold-plated connectors. Content:1 piece

€8.90*

y1303/06 TRX female to T-connector

Genuine HT spare/option part.Adapter TRX female (Traxxas batteries) to T-connector.Adapter cable for the LiPo receiver battery in model Traxxas Xmaxx.Dimensions:Length cable: 50 mmTotal length: 85 mmContent:1 piece

€9.90*

Details

y1303/10 EC5 connector, female

Genuine HT spare/option part.High quality version, contacts can be inserted into the housing from either side.Contents:1 piece

€3.90*

y1303/11 EC8 male connector

Genuine HT spare/option part.Two-pole, reverse-polarity protected plug with very high current capacity. The opening in the contact for the cable has a diameter of 6.5 mm, which is suitable for stranded cables up to about 16 mm² (~ 5 AWG). The easy to grab housing ensures easy disconnection.For assembly, the contact with a soldered cable is press fitted into the housing from the front, where it snaps into place.When used without the blue housing, the contacts are also compatible with the 8 mm sockets found on many larger ESCs.Contents:1 piece

€5.90*

y1303/15 XT60 Charging cable

Genuine HT spare/option part.Charging cable for batteries with XT60 connector, length approx. 30 cm, silicone insulated cable with gold-plated connectors.Contents:1 piece

€8.90*

y1303/12 EC8 female connector

Genuine HT spare/option part.Two-pole, reverse-polarity protected socket with very high current capacity. The opening in the contact for the cable has a diameter of 6.5 mm, which is suitable for stranded cables up to about 16 mm² (~ 5 AWG). The easy to grab housing ensures easy disconnection.For assembly, the contact with a soldered cable is press fitted into the housing from the front, where it snaps into place.When used without the blue housing, the contacts are also compatible with the 8 mm bullet connectors found on many larger brushless motors.Contents:1 piece

€5.90*

y1303/08 EC5 charging cable

Genuine HT spare/option part.Charging cable for batteries with ES5 connector, length approx. 30 cm, silicone insulated cable with gold-plated connectors.Contents:1 piece

€12.90*

y1303/07 Balancer adapter cable

Genuine HT spare/option part.Adapter cable for connecting 2S batteries with EH-balancer connector (i.e. LiFePo receiver batteries y0664 and FG 6549) to chargers with XH-terminal (i.e. Imax or Team Orion).Without connection to the balancer Lithium batteries are usually not recognized by the chargers and accordingly also not charged.Content:1 piece

€3.90*

y1303/22 EC8 Short circuit connector

Genuine HT spare/option part.Allows the use of a single 4S or 6S battery.Content:1 piece

€9.90*

y1303/21 EC5 Short circuit connector

Genuine HT spare/option part.Allows the use of a single 4S or 6S battery in a Losi Super Baja Rey / Rock Rey.Content:1 piece

€6.90*

y1303/05 EC3 connector to Universal female

Adapter EC3 male to Universal female.Adapter cable for the LiPo receiver battery in late model Losi 5ive-T and Losi Mini WRC.Dimensions:Length cable: 50 mmTotal length: 85 mmContent:1 piece

€9.90*

y1303/16 TRX female to EC5 connector

Genuine HT spare/option part.Adapter TRX female (Traxxas batteries) to EC5 connector.Adapter cable for the LiPo receiver battery in model Traxxas Xmaxx.Dimensions:Length cable: 40 mmTotal length: 85 mmContent:1 piece

€9.90*

Details

y1303/04 T male to EC5 female

Adapter cable T male to EC5 female.Dimensions:Length cable: 50 mmTotal length: 85 mmContent:1 piece

€9.90*

y1303/14 XT60 Power supply cable

Genuine HT spare/option part.Low voltage DC power supply cable with XT60 female connector for y1490 charger TT100AC Duo Touch Screen, length approx. 30 cm, silicone insulated cable with gold-plated connectors.Contents:1 piece

€8.90*

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

y1303/03 EC3 male to EC5 female

Adapter cable EC3 male to EC5 female.Dimensions:Length cable: 40 mmTotal length: 75 mmContent:1 piece

€9.90*

Details

44 products found for "y1303"

Filter products

rc-car-online - Home