y1303/27 Adapter cable XT60 male to alligator clips

rc-car-online

€9.90*

Prices incl. VAT plus shipping costs

Available

Product number: y1303_27

EAN: 4058575148098

Product information "y1303/27 Adapter cable XT60 male to alligator clips"

Genuine HT spare/option part.

Length approx. 350 mm, 18 AWG

Content:

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Similar products

6544/01 FG Charging cable EC8 with gold contacts

Genuine FG spare/option part.Contents:1 piece

€13.90*

y1303/08 EC5 charging cable

Genuine HT spare/option part.Charging cable for batteries with ES5 connector, length approx. 30 cm, silicone insulated cable with gold-plated connectors.Contents:1 piece

€12.90*

y0443 EC3 charging cord

Heavy gauge (14 AWG / 2 mm²) charging cord with EC3 plug and gold plated contacts. Especially for Losi/Horizon rx-batteries which feature an EC3 connector additionally to the regular rx-connector. The EC3 system can candle much higher charging rates which reduces charging time of high capacity battery packs significantly.Dimensions:Length approx. 20 cm

€8.90*

y0415 Receiver battery charging cable

akku_0018 Version: y0415/01 Futaba/universal+ 2.4EUR

Genuine HT spare/option part.Charging cable for receiver batteries.Content:1 piece

€11.60*

y1303/21 EC5 Short circuit connector

Genuine HT spare/option part.Allows the use of a single 4S or 6S battery in a Losi Super Baja Rey / Rock Rey.Content:1 piece

€6.90*

6544 FG Charging cable for receiver battery with FG plug

Genuine FG spare/option part. Polarized and gold plated connector system.Content:1 piece

€17.90*

y1198 Futaba transmitter charging cable - 1pce.

€6.20*

This product is no longer available.

Charging cable for receiver battery with AMP plug, y0447, 1 pcs.

Charging cable for all hump packs an batteries with AMP plug. Also fits for the internal charging jack from the HPI Baja 5b and the HPI Baja 5t cars.

€7.40*

y1303 T-connector charging cable 4mm

Charging cord for batteries with T-connector; cable length 300 mm, silicone insulated cable with gold-plated connectors.

€8.90*

y1303/25 Adapter cable T-connector male to 4 mm bullet male

Genuine HT spare/option part.Length approx. 160 mm, 18 AWGContent:1 piece

€9.90*

y1303/24 Adapter cable T-connector female to alligator clips

Genuine HT spare/option part.Length approx. 140 mm, 14 AWGContent:1 piece

€9.90*

y1303/28 Adapter cable XT60 female to XT60 male and T-connector male

Genuine HT spare/option part.Length approx. 230 mm, 14 AWGContent:1 piece

€14.90*

Customers also viewed

y1306 JETI-SBEC 6-42V voltage regulator

The switching voltage regulator SBEC is supposed to act as a current supply for receivers and servos. It makes possible to use a wide range of input voltages from 2S up to 10S Li-XX cells. Setup of the output voltage between 5 and 8V is accomplished by a shorting plug jumper. This means that the SBEC is also prepared for use with new higher voltage HV-servos. This voltage regulator is for use in combination with the Hitec Servo HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP and the special LiPo 14.8V/3,600mAh receiver battery y1304. It utilizes a 4S LiPo battery to deliver full battery voltage to the HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo with and the usual 6 - to 8 volt supply (depending on the servos) to the rest of the rx system. The output voltage is selectable. We install the required connectors to the regulator. The connection to the T/B servo is designed as a direct power supply, so even the current for the T/B servo does not run through the receiver.The regulator has connectors for battery, Receiver and T/B servo. The steering servos plugs directly into receiver and battery. The JR/universal connector on the battery is for the regulator, the BEC connector is for the steering servo power line.Attention: the switch on the voltage regulator does not disconnect the Hitec HS-1000SGT/HS-1005SGT/HS-1100WP's power output stage from the battery, which has a standby drain of about 6 mA. To prevent deep discharge of the battery, the servo must be disconnected from the battery at the end of the day!For your convenience you could install our new electronic high voltage switch y0767 between servo and battery.Wire loom and heat shrink tubing to add a matching connector to the servos power line are included. Data:Size (w/o wires): 60 x 28 x 10 mmWeight: 29 gramsInput voltage (recommended): 7 to 42 V (2S to 10S LiPo)Output voltage (selectable): 5.0 / 5.5 / 6.0 / 7.0 / 8.0 VOutput current: max. 6,2 A continuous / 12 A impulseContents:1 piece

€74.90*

This product is no longer available.