10 products found for "y1484"

rc-car-online - Home

y1489 spark plug gap tool

Genuine HT spare/option part.Low height design, allows for easy gap measurement and adjustment without damaging the electrodes.Gauge measures spark plug electrode gaps on gap plugs. Ramp style increments on the outside with a .020-.100 inches range.Use an electrode gap of about .030 for best results.Long lasting solid steel alloy.Contents:1 piece

€4.90*

y1584 Samba Moca car specific decal

Genuine rc-car-online spare/option part. Contents:1 piece

€19.90*

y1481 RC-Paint Spray Gun

Fits most spray cans from many manufacturers.Convert your spray can into a spray gun. The long-lever system of this handle makes using a spray can much more convenient and provides better flow rate control as well.No more dirty hands from paint work.Contents:1 piece

€9.95*

y1434 VL32 Multi Oil Pen for RC-Car sport

Universal maintenance oil which has a high resistance to environmental influences; it is penetrating and moisture displacing with an excellent corrosion protection. Precise application is possible with the VL32 - Multipen's metal syringe tip. The ergonomic shape and rubberized handle provide a secure grip. Leakage of oil is prevented by the safety valve in the cap. Application: u> b>Pull off cap (avoiding strong pressure on the pen!), position the pen to the point of lubrication and press. Refit cap after use.Content:12 ml / 1 piece

Content: 12 Milliliter (€741.67* / 1000 Milliliter)

€8.90*

y1486 Threading die M12 x 1,25

Genuine HT spare/option part. Die for removing the remains of microencapsulation on the stock Traxxas X-Maxx wheel shafts.After a few tire changes microencapsulation becomes very hard. This will cause the risk of thread seizure and damage. Timely removal of the residues prevents this. A die holder is not required. Turning the die with bare hands will do the job easily.Contents:1 piece

€12.90*

y1444 Mounting bracket for tuned pipe mufflers

Genuine HT spare/option part. Extra large bracket with wide surface allows for the use of two strong cable ties at the same time. You can even use a hose clamp at ones own discretion. The bracket comes with M5 lens flange head screw, nut and washer as well as with special temperature resistant cable ties. Content:BracketEach M5 screw, nylock nut and washer4 x temperature resistant cable tie 4,8 x 290 mm

€9.90*

y1474 Aluminum foil tape, self-adhesive, 50 mm x 45 meters

Genuine HT spare/option part.50 mm wide, self-adhesive aluminum foil tape, especially for heat insulation; i.e. between tuned pipe and plastic or electronic components.Content:1 piece / 45 meters

€9.90*

y1464 MadMax SUPER GRIP 170x80/x60 replacement wheels

The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video).On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T Mini should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the Mini body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.MadMax SUPERGRIP tires are available in the following compounds: (embossed marking on the inside shoulder!)Breite:Soft:Medium:60 mm y1464/01y1464/0280 mm y1464/03y1464/04For running an rc-car on tarmac, the following recommendations apply:The dirtier the track or the colder the weather, the stickier (softer) the rear tires should be.A note for the front tires: 2WD cars should run slightly harder tires in front than in rear.On 4WD cars the same compound front and rear is usually a good choice!Of course, like in full scale motorsport it also applies to the MadMax SUPERGRIP tires that the softer the tire the higher the wear. The medium compound tire lasts significantly longer than the soft version!The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks! Some off-road tires knowledge can be found here!

From €29.90*

Details

y1483 Walbro WT-1048 Racing carburetor

y1483 Version: y1483/01 WT-1048 Racing carburetor

Genuine Walbro spare/option part.Popular performance carburetor without choke; with 13.5 mm venturi diameter, especially suitable for large-displacement engines like the Zenoah G320.The stock throttle shaft has been replaced with the proper version required for car applications; including the throttle lever as well.All existing throttle linkages can therefore be connected as usual without modifications.This carburetor does not feature a primer bulb nor a connection for a return line. It is therefore only connected to the supply line from the tank, the return line of the tank has to be closed.Optional ball bearing of the throttle shaft can be selected from the shops menu.Contents:1 piece

€97.90*

y1482 Spring band clamps for tuned pipe connectors, 22 to 34 mm diameter range

y1482 Size / piece: y1482/06-5 Spring band clamps 27 - 29 mm+ 4.5EUR

Genuine HT spare/option part.Spring band clamps are self-clamping and can self-adjust to diameter changes due to temperature variations or properties of the tube material.With this feature of self-adjustment, spring band clams are ideally suited for hose connections between exhaust manifold and tuned pipe with their high temperature load.Unlike worm drive clamps with their relatively large adjustment range, spring band clamps must be selected closely related to their intended application. For this purpose, the outer diameter of the hose in the mounted state must be measured. The clamp, whose nominal diameter corresponds most accurately to the value determined, should be used.In the options menu you can select from sizes ranging from 22 to 34 mm and packs of one or five clamps.Contents:1 piece / 5 pieces

Variants from €0.99*

€5.49*

10 products found for "y1484"

Filter products

rc-car-online - Home