Tel. 0049 (0)2151-820200Nauenweg 55, 47805 KrefeldMo-Fr 9:00-18:00 Sa 9:00-13:00 o'clockQuick shipping until 14 o'clock
WK Items (0)
.. is empty

de en WorldLanguage
y1311 Hitec HS-1005SGT/HS-1100WP large mounting set for Losi 5ive-T, 2.0, 5ive-B and Mini

EUR 249,90

set - + shipping costs
all prices include VAT

1 2 3 4 5
piece: set

Available from stock
Available from stock
Place your order within the next 25.09.23 14:00:00 and we will ship Monday,  25 . September 2023

Fits 5ive-T 2.0 as well!

Set includes:

  • y1378 Dymond LiPo special high current receiver battery 14.8V/2200mAh
  • y1306 - Servo voltage regulator
  • y1307 - Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP
  • y1308/01 - Aluminum servo mount A Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP
  • y1308/02 - Aluminum servo mount B Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP
  • y1309 - All steel linkage steering servo/servo saver application

y1378 - LiPo special high current receiver battery 14.8V/2200mAh

Genuine FG spare/option part.

This battery is especially for use in vehicles which are equipped with the Hitec Servo HS-900SGS/HS-1000SGT/1005SGT/HS-1100WP for external high-voltage power supply. This battery comes with a Y-adaptor harness for two connectors, one each JST and Futaba/Universal connector. The JST connector is used for hooking up to the steering servo; the universal connector is used for the voltage regulator.

The battery fits into the standard battery box of the Losi 5ive-T.

  • Length: 110 mm
  • Width: 32 mm
  • Height: 33 mm
  • Weight: 247 gr
  • Configuration: 4S1p
  • Current rating: 40C (66 A)
  • Recommended charging current: up to 3C (2.2 A)
  • XHP(XH) -balancer connector

To increase the battery's life span it is recommended to use a charging current of approx. 0.8 A for the first three cycles.

  • 1 piece

y1306 - Servo voltage regulator

The switching voltage regulator SBEC is supposed to act as a current supply for receivers and servos. It makes possible to use a wide range of input voltages from 2S up to 10S Li-XX cells. Setup of the output voltage between 5 and 8V is accomplished by a shorting plug jumper. This means that the SBEC is also prepared for use with new „higher“ voltage HV-servos.

This voltage regulator is for use in combination with the Hitec Servo HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP and the special LiPo 14.8V/3,600mAh receiver battery y1304. It utilizes a 4S LiPo battery to deliver full battery voltage to the HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo with and the usual 6 - to 8 volt supply (depending on the servos) to the rest of the rx system. The output voltage is selectable.

We install the required connectors to the regulator. The connection to the T/B servo is designed as a direct power supply, so even the current for the T/B servo does not run through the receiver.
The regulator has connectors for battery, Receiver and T/B servo. The steering servos plugs directly into receiver and battery. The JR/universal connector on the battery is for the regulator, the BEC connector is for the steering servo power line.

Attention: the switch on the voltage regulator does not disconnect the Hitec HS-1000SGT/HS-1005SGT/HS-1100WP's power output stage from the battery, which has a standby drain of about 6 mA. To prevent deep discharge of the battery, the servo must be disconnected from the battery at the end of the day!

For your convenience you could install our new electronic high voltage switch y0767 between servo and battery.

Wire loom and heat shrink tubing to add a matching connector to the servo’s power line are included.

  • Size (w/o wires): 60 x 28 x 10 mm
  • Weight: 29 grams
  • Input voltage (recommended): 7 to 42 V (2S to 10S LiPo)
  • Output voltage (selectable): 5.0 / 5.5 / 6.0 / 7.0 / 8.0 V
  • Output current: max. 6,2 A continuous / 12 A impulse

  • 1 piece

y1307 - Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP Losi 5ive-T, 5ive-B and Mini

Genuine HT spare/option part.

This extremely strong servo horn is specifically designed with dimensions for the installation of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high-performance servo in the Losi 5ive-T and Mini for steering application, but it can be used in other cars with this kind of servo.

It bolts directly to the servo’s stock aluminum disk.

The lever of this arm is longer than that of the servo saver. This gives you faster actuating speed of the steering.

A linkage with a double-sided arm can only be done properly if all corresponding levers are the same length and the linkages run exactly parallel. If this is not the case, the servo and servo saver shaft will try to change the distance to each other with every steering movement . Thus, undesirable constraining forces.
For this reason we decided to give preference to the single-sided arm.

Scope of delivery:
  • 1 x Aluminium servo horn
  • 4 x Socket head cap screws 3 x 14 mm
  • 1 x Socket head cap screws 4 x 30 mm
  • 1 x Self-locking
  • hexagon nut M4
  • 4 x Shim ring 3,2

  • 1 piece

y1308/01 + y1308/02 - Aluminum servo mounts Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP Losi 5ive-T, 5ive-B and Mini

Genuine HT spare/option part.

These servo mounts allow for a simple and strong mounting of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high power servo for steering application.
The massive servo mounts bolt to the chassis using existing mounting holes. The mount for the stock servo has to be cut off the radio plate. The aluminum servo mounts feature a pair of additional mounting holes to install a stock servo should ever the need arise.

The rear mount bolts to the radio plate as well, providing additional support for the plate.

Scope of delivery y1308/01:
  • 1 x Mount A
  • 2 x Socket head cap screws 3 x 16 mm
  • 2 x Countersunk screw 4 x 14 mm
  • 2 x Shim ring 4,2 mm

Scope of delivery y1308/02:
  • 1 x Mount B
  • 1 x Socket head cap screw 3 x 25 mm
  • 1 x Socker head cap screw 3 x 16 mm
  • 2 x Countersunk screw 4x14 mm
  • 2 x Shim ring 3,2 mm

  • 1 set

y1309 - All steel linkage for Losi 5ive-T and Mini steering servo/servo saver application

Genuine HT spare/option part.

Very strong linkage with M6 steel ball joints.
M6 threaded rod with lock nuts, balls with holes for M4 screws.

Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.

Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.

The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.

On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.

Set includes:

  • 2 x steel ball joints M6
  • 2 x flat lock nuts
  • 1 x M6 x 60 mm threaded piece for Losi 5ive-T
  • 1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.0
  • 2 x spacer tubes

  • 1 piece


Your name:
Your email address:
Your question:

Your email address will never be published!

Privacy Policy
Our site uses cookies and similar technologies. By using the website, you consent to the use of cookies. You can find more information in our Data protection