Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

43 products found for "y1306"

Filter products

rc-car-online - Home

Average rating of 0 out of 5 stars

y1306 JETI-SBEC 6-42V voltage regulator
The switching voltage regulator SBEC is supposed to act as a current supply for receivers and servos. It makes possible to use a wide range of input voltages from 2S up to 10S Li-XX cells. Setup of the output voltage between 5 and 8V is accomplished by a shorting plug jumper. This means that the SBEC is also prepared for use with new higher voltage HV-servos. This voltage regulator is for use in combination with the Hitec Servo HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP and the special LiPo 14.8V/3,600mAh receiver battery y1304. It utilizes a 4S LiPo battery to deliver full battery voltage to the HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo with and the usual 6 - to 8 volt supply (depending on the servos) to the rest of the rx system. The output voltage is selectable. We install the required connectors to the regulator. The connection to the T/B servo is designed as a direct power supply, so even the current for the T/B servo does not run through the receiver.The regulator has connectors for battery, Receiver and T/B servo. The steering servos plugs directly into receiver and battery. The JR/universal connector on the battery is for the regulator, the BEC connector is for the steering servo power line.Attention: the switch on the voltage regulator does not disconnect the Hitec HS-1000SGT/HS-1005SGT/HS-1100WP's power output stage from the battery, which has a standby drain of about 6 mA. To prevent deep discharge of the battery, the servo must be disconnected from the battery at the end of the day!For your convenience you could install our new electronic high voltage switch y0767 between servo and battery.Wire loom and heat shrink tubing to add a matching connector to the servos power line are included. Data:Size (w/o wires): 60 x 28 x 10 mmWeight: 29 gramsInput voltage (recommended): 7 to 42 V (2S to 10S LiPo)Output voltage (selectable): 5.0 / 5.5 / 6.0 / 7.0 / 8.0 VOutput current: max. 6,2 A continuous / 12 A impulseContents:1 piece

€74.90*

Average rating of 0 out of 5 stars

y0306 Step drill for body work
Genuine HT spare/option part. Small and handy step drill, made of TiN-coated HSS steel with steps of 4/6/8/10/12 mm. Split point tip for good centering, 6 mm tri-flat shank for sure grip. For use with drills or with our hand chuck.Contents:1 piece

€9.90*

Average rating of 0 out of 5 stars

y1303 T-connector charging cable 4mm
Charging cord for batteries with T-connector; cable length 300 mm, silicone insulated cable with gold-plated connectors.

€8.90*

Average rating of 0 out of 5 stars

y1307 Aluminum servo horn Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP
Genuine HT spare/option part.This extremely strong servo horn is specifically designed with dimensions for the installation of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high-performance servo in the Losi 5ive-T and Mini for steering application, but it can be used in other cars with this kind of servo.It bolts directly to the servos stock aluminum disk.The lever of this arm is longer than that of the servo saver. This gives you faster actuating speed of the steering.A linkage with a double-sided arm can only be done properly if all corresponding levers are the same length and the linkages run exactly parallel. If this is not the case, the servo and servo saver shaft will try to change the distance to each other with every steering movement . Thus, undesirable constraining forces.For this reason we decided to give preference to the single-sided arm.Scope of delivery:1 x Aluminium servo horn4 x Socket head cap screws 3 x 14 mm1 x Socket head cap screws 4 x 30 mm1 x Self-lockinghexagon nut M44 x Shim ring 3,2Contents:1 piece

€39.90*

Average rating of 0 out of 5 stars

y1036 HT rose joints with conical spacers
Genuine HT spare/option part. Dimensions:A = 5 mmB = 6 mmC = 8 mmD = 13 mmContents:2 pieces rose joints4 pieces conical spacers

€18.90*

Average rating of 0 out of 5 stars

y1360 MD Two-component glue CA-STAR 2K met
Best adhesion properties on many different materials: many metalls like steel / aluminum / stainless steel, many plastics, rubber, porous / absorbent materials.Mixing ratio: 4:1Processing time: approx. 35 minutes Temperature resistance: -20°C to +80°C, short term up to +120°CFeatures:ThixotropicDrip freeExtremely impact resistantMechanical editableGap fill up to 6 mmApplications overhead and in vertical locationsGood chemical resistanceLow bloomingColor: grey

Content: 10 Milliliter (€1,690.00* / 1000 Milliliter)

€16.90*

Average rating of 0 out of 5 stars

y1309 All steel linkage for steering servo/servo saver application
Genuine HT spare/option part.Very strong linkage with M6 steel ball joints.M6 threaded rod with lock nuts, balls with holes for M4 screws.Maximum length about 96 mm, but through cutting the M6 rod allows for a minimum length of 48 mm.Significantly stronger than the standard plastic version, and especially recommend when using the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP servo, this linkage can be used with "normal" servos as well.The threaded rod is not designed as a turnbuckle for a reason because there is not need to change the adjusted length for this application after installation. The setting accuracy of 0.5 mm (½ turn) means a maximum difference to the ideal length of 0.25 mm. This is always sufficient, the trim on the transmitter handles the final adjustment.On the other hand, a connecting rod with the same thread on both ends will always keep its setting when installed, even when both lock nuts are not tightened against the ball joints. Therefore reliability is higher.Set includes:2 x steel ball joints M62 x flat lock nuts1 x M6 x 60 mm threaded piece for Losi 5ive-T1 x M6 x 80 mm threaded piece for Losi 5ive-T 2.02 x spacer tubesContents:1 piece

€27.90*

Average rating of 0 out of 5 stars

y1376 Full set of gaskets for Zenoah G240, G270, G290, and 4-Bolt CY engines
Full set of gaskets for Zenoah G40, G270, G290, and 4-Bolt CY engines.Set includes:0.4 mm cylinder gasket (Zenoah stock thickness!)1 mm exhaust gasket0.5 mm crankcase gasket0.5 mm isolator gasket0.5 mm carburetor gasket

€12.90*

Average rating of 0 out of 5 stars

y1396 Reed valve piston
y1396 Version: y1396/29 - Zenoah G290
Genuine Zenoah piston with machined recess for use with Are reed valve block BJ035. Please note: Differing widths of the remaining webs of the piston skirt are caused by production spread of the pistons.Version:y1396/29 - Zenoah G290y1396/32 - Zenoah G320Content:1 piece

€39.90*
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
By submitting the form, I accept the general terms and conditions as well as the privacy policy.

Average rating of 0 out of 5 stars

2012-42 Mecatech Spherical Bearing, replaces to y1036
Genuine Mecatech spare/option part for the FW01.Content:2 pieces

€27.90*

Average rating of 0 out of 5 stars

y1308 Aluminum servo mounts Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP Losi 5ive-T, 5ive-B and Mini
y1308 Version: y1308/03 Set with mount A and Mount B+ 27.9EUR
Genuine HT spare/option part.These servo mounts allow for a simple and strong mounting of the Hitec HS-900SGS/HS-1000SGT/HS-1005SGT/HS-1100WP high power servo for steering application.The massive servo mounts bolt to the chassis using existing mounting holes. The mount for the stock servo has to be cut off the radio plate. The aluminum servo mounts feature a pair of additional mounting holes to install a stock servo should ever the need arise. The rear mount bolts to the radio plate as well, providing additional support for the plate.Scope of delivery y1308/01:1 x Mount A2 x Socket head cap screws 3 x 16 mm2 x Countersunk screw 4 x 14 mm2 x Shim ring 4,2 mmScope of delivery y1308/02:1 x Mount B1 x Socket head cap screw 3 x 25 mm1 x Socker head cap screw 3 x 16 mm2 x Countersunk screw 4x14 mm2 x Shim ring 3,2 mmContents:1 set

Variants from €44.90*
€72.80*

Average rating of 0 out of 5 stars

y1366 TURBO-TWIST 325 mm special XXL screw driver
y1366 Version: y1366/01 - Phillips no. 0 / PH0
TURBO-TWIST, 325 mm long screw driver in top quality.Allows easy access to hard-to-reach screws in any 1/5 & 1/6 car.Features:Soft Grip handlesExtra long 325 mm shaftChrome Vanadium hardened and tempered bladesBlackened magnetic tipsVersions:y1366/01 - Phillips No. 0 / PH0y1366/02 - Phillips No. 1 / PH1y1366/03 - Phillips No. 2 / PH2y1366/04 - Flat 1.2 x 8 x 325 mm

€6.90*

Average rating of 0 out of 5 stars

y1206 HT Aluminum front lower l/r a-arm for Smartech Off-Road
y1206 Content of delivery: set with l/h andr/h version+ 30EUR
Genuine HT spare/option part.Very strong one-piece a-arm for use with rose joints. Features Igus bushings for the hinge pins (stock hinge pins can be re-used). Rose joint and conical spacers included!Fits Smartech MT Carson Comanche, Attack Evo, CRT + CPT, l/h version!Contents:1 piece

Variants from €59.90*
€89.90*

Average rating of 0 out of 5 stars

y1301 T-connector male / female spring loaded 4 mm contact
y1301 Version: y1301/03 male + female+ 1.8EUR
T-connector male / female with spring loaded 4 mm contact.Select from:y1301/01 - male connectory1301/02 - female connectory1301/03 - one each male and female connector

Variants from €1.80*
€3.60*

Average rating of 0 out of 5 stars

y1303/04 T male to EC5 female
Adapter cable T male to EC5 female.Dimensions:Length cable: 50 mmTotal length: 85 mmContent:1 piece

€9.90*

Average rating of 0 out of 5 stars

y1303/06 TRX female to T-connector
Genuine HT spare/option part.Adapter TRX female (Traxxas batteries) to T-connector.Adapter cable for the LiPo receiver battery in model Traxxas Xmaxx.Dimensions:Length cable: 50 mmTotal length: 85 mmContent:1 piece

€9.90*

Average rating of 0 out of 5 stars

y1303/10 EC5 connector, female
Genuine HT spare/option part.High quality version, contacts can be inserted into the housing from either side.Contents:1 piece

€3.90*

Average rating of 0 out of 5 stars

y1303/11 EC8 male connector
Genuine HT spare/option part.Two-pole, reverse-polarity protected plug with very high current capacity. The opening in the contact for the cable has a diameter of 6.5 mm, which is suitable for stranded cables up to about 16 mm² (~ 5 AWG). The easy to grab housing ensures easy disconnection.For assembly, the contact with a soldered cable is press fitted into the housing from the front, where it snaps into place.When used without the blue housing, the contacts are also compatible with the 8 mm sockets found on many larger ESCs.Contents:1 piece

€5.90*

Average rating of 0 out of 5 stars

y1303/17 XH Balancer extension cable 2S-4S
y1303_17 Version: y1303/17-S3 XH Balancer extension cable+ 0.5EUR
Genuine HT spare/option part.Extension cable for convenient charging of LiPo batteries with XH connector, since the standard balancer connection on the battery is usually uncomfortably short. Available for 2S, 3S and 4S batteries. Silicone insulated cables with a length of approx. 20 cm.Content:1 piece

Variants from €3.40*
€3.90*

Average rating of 0 out of 5 stars

y1303/02 EC3 to female T-connector adapter cable
Adapter cable EC3 male to T-connector femaleDimensions:Length cable: 46 mmTotal length: 72 mmContent:1 piece

€9.90*

Average rating of 0 out of 5 stars

y1303/18 T-connector male to HXT4 battery side
Genuine HT spare/option part.Adapter cable T-connector male to HXT4 battery side. Dimensions:Cable length: 50 mmTotal length: 97 mmContent:1 piece

€9.90*

Average rating of 0 out of 5 stars

y1106/02 Aluminum ball joints with 5mm/M8 left-hand thread, 2 pieces
Genuine HT spare/option part.Two balljoints 5mm/M8 left-hand threadThe maintenance-free rod ends with the sliding contact surface combination steel/ bronze composite feature a spherical plain bearing with a brass outer ring which is lined with a layer of bronze web in to which PTFE with molybdenum disulphide has been rolled. Dimensions:A = 5 mmB = M8 rightC = 8 mmD = 17,5 mmE = 39 mmContents:2 piece

€14.90*

Average rating of 0 out of 5 stars

y1303/26 Adapter cable T- connector female to Tamiya female
Genuine HT spare/option part.Length approx. 160 mm, 18 AWGContent:1 piece

€9.90*

Average rating of 0 out of 5 stars

y1303/12 EC8 female connector
Genuine HT spare/option part.Two-pole, reverse-polarity protected socket with very high current capacity. The opening in the contact for the cable has a diameter of 6.5 mm, which is suitable for stranded cables up to about 16 mm² (~ 5 AWG). The easy to grab housing ensures easy disconnection.For assembly, the contact with a soldered cable is press fitted into the housing from the front, where it snaps into place.When used without the blue housing, the contacts are also compatible with the 8 mm bullet connectors found on many larger brushless motors.Contents:1 piece

€5.90*
Loading...
Upload in progress, please be patient ...
Shopware-Agency Shopware-Theme Development