14 products found for "y1202"

rc-car-online - Home

Expert gilmer belt for all FG 1/6 4WD cars, y1202, 1 pce.

Dimensions same as FG 66237with reinforced glas cord, polyamide fabric and polychloroprene backside. For all FG Offroad 4WD models with 490-510mm ( Offroad buggy, monster and stadium) and all FG Sportsline 4WD 510 ( Porsche GT3, Mini and BMW E30 ) leng 635mm, wedth 18mm.

€29.90*

y1208 HT Aluminum a-arm for Carson/Smartech Off-Road

Genuine HT spare/option part.Very strong a-arm, allows for camber adjustment. Features Igus bushings for the hinge pins (stock hinge pins can be re-used).Fits Smartech Monster, Carson Comanche, Attack Evo, CRT 2WD and CPT. Contents:1 piece

€39.90*

y1602 SPEED TEC CRANK Team-Edition Zenoah G260 Tuning engine

The SPEED TEC CRANK genuine Zenoah engine is optimized for performance by hand with sophisticated craftsmanship and guarantees, besides greatly increased performance, excellent workmanship and stamina. SPEED TEC Team Edition version modifications: Cylinder & case:Adjustment of compression; enlarged ports, fuel management milled, machined and polished exhaust, the intake is flow-optimized the case is specially matched with enlarged and flow-optimized cross section towards the ports Piston:Transfer port area optimized for flow, weight reduced and the piston-roof is flow-optimized and polishedCrankshaft:is adjusted, aligned and balancedFlywheel and ignition:Latest SPEED TEC CRANK SV ignition system for rc-car race engines with air baffles, a special balanced 62 mm diameter flywheel, modified ignition coil mount and special ignition system allows for the extremely fast revving of the SPEED TEC team edition engine and guarantees a significantly improved performance.The machined and more than 30% lighter than stock CRANK flywheel with fins on both sides contributes to the optimized engine cooling.Gaskets:Premium quality gaskets installed. Cylinder gasket installed using elastic gasket sealer.Isolator:Special matched and raised insulator Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

€949.00*

y1209 HT Aluminum front bulkhead A for Carson/Smartech, Reely and FG

Genuine HT spare/option part.With provision to mount a stabilizer bar and replaceable bushings for the hinge pins.Fits Comanche, Attack Evo, CRT 2WD, CPT, C5, R5, FG Sportsline and Smartech Contents:1 piece

€49.90*

y1203 HS gilmer belt for FG 4WD cars, 1 pce.

Dimensions same as FG 66237.Very high rupture strength and tearing resistance as well as reduced wear make this belt the perfect choicefor race applications where maximum reliability is a must.Fits cars with 490 and 510 mm wheelbase only. Does not fit WB535 cars! For all FG Offroad 4WD models with 490-510mm ( Offroad buggy, monster and stadium) and all FG Sportsline 4WD 510 ( Porsche GT3, Mini and BMW E30 ) leng 635mm, wedth 18mm.

€34.90*

y1204 HT Aluminum front suspension for Carson Comanche, Attack Evo, CRT 2WD + CPT, Smartech MT, Pick-up Truck, Cross Beetle, Monster Beetle

The set includes:Item N°Name:y1206HT Aluminum a-arm front lower l/hy1207HT Aluminum a-arm front lower r/hy1208HT Aluminum a-arm front uppery1209HT Aluminum front bulkhead Ay1210HT Aluminum front bulkhead By1036HT rose joints with conical spacersUnit prices: 249,00 EURPlease note: the hinge pins are not included, you will use the pins from the stock suspension!Suitable for Carson 1/6 (Comanche, Attack Evo, CRT + CPT) and Smartech Monster Truck.Price for the parts bought separately: 253,30 EURIntroductory price: 179,90 EUR / set

€249.00*

y1205 HT Aluminum rear suspension conversion kit for Smartech MT, Carson 2WD, Comanche, Attack Evo, CRT + CPT, Pick-up Truck, Cross Beetle, Monster Beetle

Alloy rear axle conversion kit for Carson 2WD Comanche, Attack Evo, CRT + CPT and Smartech Monster Truck.The set includes:rear platedifferential mountslower a-armsupper a-armssteel turnbuckles for upper a-armsinstallation hardware.Please note: the hinge pins are not included, you will use the pins from the stock suspension!

€229.90*

y1406/01 MadMax BIG DIGGER 170x80/x60 complete set for Traxxas X-MAXX 4x4 with adapter

Offerset:1 Pair MadMax Big Digger front tires 170x60 mm1 Pair MadMax Big Digger rear tires 170x80 mm1 Pair MadMax front rims 60 mm1 Pair MadMax rear rims 80 mm1 Pair MadMax front inlays 60 mm1 Pair MadMax rear inlays 80 mm2 Pairs / 4 pieces adapter TT1020/01BIG DIGGER 170x80 and 170x60 with black MadMax Extreme rims with 20 beadlock screws, with 24 mm hex socket and reinforced orange headlock rings for Losi 5ive-T and Desert Buggy XL as well as all HPI Baja 5 cars.The MadMax tires had 84 extremely strong tread blocks on the front tires and 96 on the rears, with more than 1 cm² cross-section and 6 mm tread depth, allow for best power transfer and provide excellent grip even on loose surfaces like sand or soil. Due to the extreme load created by the MadMax BIG DIGGER tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars like the Losi 5ive-T.The set consists of two each front and rear tires, including tire inserts and MadMax EXTREME rims and 4 pieces adapter wheel nuts TT1020/01.We recommend to check the beadlock screws after the run. Dimensions:Outside diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 24 mm hex wheel driveThe video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!TT1020 Top Tuning Adapter wheel nutGenuine TopTuning spare/option part.These adapter nuts, manufactured from billet 7075 aluminum allow for easy and precise installation of all MadMax, HPI and Losi tires and rims on the Traxxas X-Maxx. For the best result possible, nut and adapter are manufactured as a one-piece unit.It should be noted that the wide rims can be used on the rear axle only. On the front axle they would limit the steering angle by grinding on lower a-arm and steering rod.Traxxas has microencapsulated the wheel shafts of the X-Maxx to secure the wheel nuts. Like any thread locking compound this is not for eternity. After several tire changes the use of a normal screw locking compound is advised, we recommend it "y0113 / 01 medium strength".The dimensions of the nut are specifically designed for use with MadMax, current HPI and Losi rims. Rims from Losi 5ive have slightly different dimensions in the hub area. This is meaningless on the large LOSI or HPI wheel adapters. With the smaller and shorter wheel nut thread of the X-Maxx wheel shafts you cannot compromise. Therefore there are also special nuts for the Losi rims/wheels available at our options menu.However, somewhere in the past, the injection moulds for the HPI rims were slightly modified in the hub area. As part of that job the bore diameter has probably been slightly increased. Therefore, the use of older rims in combination with the adapter nuts makes it necessary to increase the rim bore a little bit.Due to repeated requests for use: these wheel nuts replace the stock wheel nuts when installing the wheels!Contents:4 pieces

€139.90*

Configure now

y1242, Inclined air filter adapter for HPI Baja and Carson Wild Attack GP, set

This 15° inclined adapter allows for easy access for filter servicing or installation of a precleaner like the Twinair filter skin. This beautifully machined part comes with all the hardware and gaskets needed.Fits all cars from the HPI Baja 5 series and Carson Wild Attack GP.The adapter must be used with the stock airfilter, but replaces the stock adapter plate. Installation of other filters is not possible, but not necessary either since the HPI filter is one of the best filters on the market.The special design improves airflow for better performance.Outer diameter 64 mmInner diameter 54 mmOverall height 27 mm

€19.90* €49.90* (60.12% saved)

y0202 HT-Differential ring gear, extreme duty, 41Teeth

Genuine HT spare/option part.Coarse pitch spur gear for the differential, especially for use in off-road and monster models. The teeth are stronger and , due to their bigger size, a little bit more forgiving when the gear mesh is not adjusted correctly.Fits FG cars and Smartech / Carson 2WD cars.Only for use with the extreme duty pinions! Not for use in combination with Elcon rear drivetrain unit or Elcon differential!Module: m=1,75.Contents:1 piece [INCLUDE]profilverschoben[ENDINCLUDE]

€49.90*

y1206 HT Aluminum front lower l/r a-arm for Smartech Off-Road

y1206 Content of delivery: set with l/h andr/h version+ 30EUR

Genuine HT spare/option part.Very strong one-piece a-arm for use with rose joints. Features Igus bushings for the hinge pins (stock hinge pins can be re-used). Rose joint and conical spacers included!Fits Smartech MT Carson Comanche, Attack Evo, CRT + CPT, l/h version!Contents:1 piece

Variants from €59.90*

€89.90*

y1212 HT Aluminum rear lower a-arm r/h for Smartech/Carson Off-Road

y1212 Content of delivery: Set with l/h and r/h version+ 25EUR

Genuine HT spare/option part.Lower rear a-arm with replaceable bushings for the hinge pin. Comes with two M8 low height nuts included.Fits Smartech MT, Carson Comanche, Attack Evo, CRT 2WD, CPT. Contents:1 piece

Variants from €34.90*

€59.90*

y1207 HT Aluminum front lower a-arm r/h for Carson/Smartech Off-Road

y1207 Content of delivery: Set with l/h andr/h version+ 30EUR

Genuine HT spare/option part.Very strong one-piece a-arm for use with rose joints. Features Igus bushings for the hinge pins (stock hinge pins can be re-used). Rose joint and conical spacers included!Fits Smartech Monster-Truck, UNO, Carson Comanche, Attack Evo, CRT and CPT. Contents:1 piece

Variants from €59.90*

€89.90*

Mielke S-1202 Clutch bell for SR 88 R (Mecatech System)

Genuine Mielke spare/option part. Contents:1 piece

€59.90*

14 products found for "y1202"

Filter products

rc-car-online - Home