y1189 Stadium wheels on disc rim, 2 pairs
Product information "y1189 Stadium wheels on disc rim, 2 pairs"
Complete set of four CRT stadium tires and rims, mounted and glued with tire inserts. Fits FG and Carson 1/6 scale cars.
Tire diameter 170 mm, tire width 80 mm, 18 mm wheel square. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.
Tire diameter 170 mm, tire width 80 mm, 18 mm wheel square. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.
| Also suitable for: | |
 | |
| With the following wheel adapter: y1183 Rim adapter | |
Login
Alternatives
If you want a special combination of compounds please enter that information into the "note to us" form field at the end of the checkout process.Mammoth Supergrip for 1/6 and 1/5 offroad cars. Fits too for Formular 1 models!Parking lot / race tires for your offroad car.VersionWidthOuter diameterFront64 mm153 mmRear78 mm153 mmGlued on genuine FG rims (rear tires using extension rings), with foam rubber inserts included. Rim has 18 mm square drive with reinforcement ring.Please note: based on experience we recommend against using other manufacturers rims and extensions. Since the Mammoth tires provide very good grip the rim and the bonding must withstand high loads. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.The Mammoth Supergrip is available in in the following compounds: Super softSoftMediumHardFront tirey0581y0582y0583y0584Rear tirey0591y0592y0593y0594General recommendation:The dirtier the track or the lower the ambient temperatures, the stickier (softer) the rear tires should be.Hint regarding the front tires: 2WD cars should use them one or two grades harder then the rears. 4WD cars usually like the same compound all around.Of course, the softer the tire the higher the wear rate; and this applies to Mammoth Supergrip onroad tires as well.The tires have a special onroad thread pattern but will still provide ideal traction after the pattern has been worn out. The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall.Prices per unit: FrontRearMammoth Supergrip:Pair44,90 EUR49,90 EURTire inserts:Pair13,00 EUR13,00 EURFG rim:Pair14,90 EUR14,90 EURFG extension ring:Pair--.-- EUR14,90 EURMounting:Pair13,00 EUR13,00 EURTotal Price 85,80 EUR 105,70 EUR = 191,50 EUR SETTotal for 1 pair each front and rear: 169,90 EUR================================Also suitable for:With the following wheel adapter: y1183 Rim adapter
Customers also viewed
%
Genuine HT spare/option part. Spare part for engine quick mount y1421.
grp_w70 Rubber compund:
Soft - GWH70A
Item N° GWH70 GRP 1:6 Buggy "CUBIC" tire glued, 2 pcs.fine lug treadvery good directional stabilitylow lateral tractionmoderate propulsionfor hard packed surfaceTire diameter: 164 mm Tire width: 61 mmDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Attention:On all 2WD cars (except Leopard 2WD) the front suspension must be equipped with the combination of uprights y0932 and steering rods FG #7028/01. Wheel squares FG #6107/02 must be used in front and rear. 4WD cars must only use the wheel squares FG #6107/02 in front and rear.
The Maxi-Pin competition tire is particularly suitable for tracks with a hard packed surface, as well as for tracks with a higher percentage of carpeting. The tread is not extended into the tire?s sidewall to reduce the side bite of the Maxi-Pin tire; the car remains controllable on such challenging tracks, which makes this tire a must-have for your "tire box"! Since the Maxi-Pin tire has many fine pins for a high number of biting edges and a low tread depth for reduced flex work, depending on the track's surface increased tire wear may be expected.Unit pricesOne pairMaxi-Pin tires39.90 EUR79.80 EUROne pairTire inserts9.90 EUR19.80 EUROne pair32482 Buggy rim14.90 EUR29.80 EUR64.70 / 129.40 EURDimensions:Diameter: 155 mmWidth: 67 mmInner diameter: 106 mm
The FG Off-Road Buggy WB535 is presented with a longer wheelbase and a pleasant design. All-wheel-drive, completely mounted ready-to-drive, combined with the open Off-Road Buggy body shell with metal roll cage and gigantic Off-Road rims with low-profile knobbed tires.The body shell is standard unpainted. Equipped with a 26cm³ engine the Off-Road Buggy is aggressive and also a tremendous jumper. The 35 mm wheelbase extension results in a higher tracking stability. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Equipment of the modelAngled 4 mm, alloy chassis, completely covered belt drive, two differential gears at front and rear axle with hardened bevel gearwheels, closed front axle housing, front bumper, double wishbones at front and rear axle, gear brake, adjustable right/left thread rods at the track rods and at the front and rear wishbones, front uprights with steering stops, gearwheels made of case-hardened steel, completely ballbeared, four large-volume oil-pressure shock absorbers, receiver box.According to side rails and the closed body shell the Off-Road Buggy is almost protected against dirt from underneath. The two-parts body shell is made of polycarbonate, the rear spoiler is made of impact resistant polyamide. Driver´s coverage and roll cage parts are made of aluminum. The giant low-profile knobbed tires are glued on black rims.The model is equipped with a powerful 26cm³ (series) combustion engine with ready-for-use oiled air filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every patrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-stat system the engine can be started without any difficulties. HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount bigCNC machined alloy engine mount, direkt replacement for the stock plastic part, heat and tweak resistant. They come with all necessary hardware included. Value: 64,95 EUR Alloy spur gear carrierUse for 39T - 44 teeth spur gears.Value: 39,90 EUR Ball bearing set, sealed, set of 14The seal rings on sealed ball bearings keep dirt and dust out of the bearings. They are therefore particularly suitable for use in dirty and dusty environments.Value: 59,90 EURTotal value: 227,35 EURThe RTR version is delivered with installed and preset radio control system and rechargeable batteries. To complete the non-RTR version all popular servos and radio control systems are suitable.The pictures may display the car with some optional items which are not included, like bed-mounted rollbar, lights, front bumper or mirrors. These items can be added in the drop down menus.Measures:Length: 770 mmWidth: 480 mmHeight: 280 mmWheelbase: 535 mmWeight: 10,8 kg
Genuine UFRC spare/option part. Original equipment tires of the Ghost Rabbit GR1.Fits Losi MTXL as well.When using our special wheel nuts TT1020/02 these tires can also be mounted on the Traxxas X-Maxx.Tire with vulcanized Kevlar belt, speed resistant (no ballooning) and yet flexible.Rim with steel hex insert.Diameter 230 mm, width 100 mm, 24 mm hex wheel drive.Rim thickness at center hole: 8.75 mm.Hex depth: 8 mm.Weight: approx. 2160 grams/pairOn the Losi DBXL running these wheels requires the installation of the DBXL024 ATOP axle extenders!Contents:2 pieces