SB015TSH GPM aluminum split servo horn for 15T shaft
Product number:
gpm_sb015tsh
EAN:
4894538305142
Product information "SB015TSH GPM aluminum split servo horn for 15T shaft"
Genuine GPM spare/option part.
Extremely sturdy split-style servo horn, fits servos with 8 mm/15T output shaft (e.g. DM4000, large Savöx/Losi/Hitec, Multiplex Rhino etc.). It is therefore also suitable for use in many other applications.
Linkage mounting holes tapped for M4 screws.
Contents:
Extremely sturdy split-style servo horn, fits servos with 8 mm/15T output shaft (e.g. DM4000, large Savöx/Losi/Hitec, Multiplex Rhino etc.). It is therefore also suitable for use in many other applications.
Linkage mounting holes tapped for M4 screws.
Contents:
- 1 piece
Login
Customers also bought
Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece
%
Genuine HT spare/option part. Universal radio plate for FG 4WD Marder; Off-Road Buggy; Beetle and all 4WD Monster and Stadium Modelle. Optional for one or two servos.With drilling templates for up to two of the following steering servos:Big Scale Servo:Orange PowerHitec Servos:HS-805BB/MGHS-5745HS-5755FG Servos:65956596/li>Multiplex Servos:Jumbo´sRhinoCarson Servos:Mega EvoMega Evo ProAnd for all servos with the from 59x29x55 mm, 66x30x70mm. Parts like servos and decoration are not included! Spacers for throttle/brake servo (standard size) and rx-box are included.Delivery contents:Servo plateMountin boltsSpacerScrews and mounting materialThe surface is plain aluminum. With the necessary effort it can be polished to a high luster.
y0040 Variant:
y0040/01 Incl. locking parts for Coupling member A+ 4.9EUR
The secure hose connection for engine or tank removal! Advantages of the Kent system quick couplings: A safe opening and closing with one hand, as soon as one side is fixed. The design of the "shut-off" valve is a double chamber system, which closes when disconnecting the coupling. (This design enables easy and safe opening of the quick couplings, even under high pressure. Similarly, just as in low pressure applications.) You feel a snap when connecting the couplings, preventing over-tightening or accidental opening. The actions of opening and closing the quick couplings are identical, so that the handling is extremely simple. An ergonomic design guarantees easy handling, yet the space requirement for the couplings is low. Long and safe life of the couplings even with frequent connection and disconnection. In order to protect the fully encapsulated KENT quick coupling system against dirt even after dismantling, sealing the ends with the corresponding white plugs and caps is recommended.
Variants from €16.90*
Item N° y0700/01 Single-sided alloy servoarm, 1 pce.Suitable for all servos with an output shaft with 25 teeth multi-tooth shaft, for example:y2006 Digital Big-Scale Servo D-21HVNearly all Robbe/Futaba servosMega Power servoThunder Tiger DS1015Savöx servosand many more!When you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarms are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.
at_5t020 Version:
AT-5T020-01 - 0236
Genuine ATOP spare/option part.CNC-machined from 6061-T6 aluminum by ATOP. CNC-machined 6061-T6 aluminum servo clamps from Area RC distribute the load from the mounting screws equally over the complete area of the mounting tabs, protecting them against breakage. Available in two versions:AT-5T020-01 - 0236 for stock servos in Losi 5ive and DBXL, Savöx 235 und 236, Orange Power and other servos with a mounting hole distance of 18 mmAT-5T020-02 - 5765 for MPX Rhino, Hitec 5765 and other servos with a mounting hole distance of 16 mmContents:2 pieces
Genuine ATOP spare/option part. CNC machined 6061-T6 aluminum rear uprights from ATOP to fit all Losi DBXL and MTXL versions, gasoline and electric.Significantly more rigid than the stock plastic version, this part contributes to increased directional stability. Plastic bushings for the hinge pins ensure reduced wear.Two additional mounting points are available for attaching the camber rods, allowing the model's handling to be better matched to the track.Comes with wheel bearings included. Contents:2 pieces
Customers also viewed
y0711_alle Version:
y0711 Double sided split alloy servoarm+ 2.9EUR
Splitted Alloy servoarm for a more protecting screw connection (with a 2,0 mm allen head screw driver) causing stiffness on the servo output shaftSuitable for all servos with an output shaft with 15 tooth spline shaft, for example:K-Power DM4000Multiplex RhinoHitec 805Savöx SV-0236MGSpektrum S9010 and S9020LOSB 0886 S901T (Original Losi 5ive-T throttle Servo servo)LOSB 0884 S900S (Original Losi 5ive-T steering servo)Losi SPMS904 WPand many more!holes for linkage with M3 threadWhen you count the teeth of your servo you can check if this alloy arm will fit to your servo. Alloy servoarms are indispensable by strong digital servos, as used on big scale models for example, to optimize the servo forces being transferred.Content:1 pieces
Genuine HPI spare/option part. Distances bore to center of servo horn: 26 and 31 mm. Holes tapped with M3 thread.This aluminum steering arm is built extra tough to handle the demands of 1/5th scale vehicles. Use it as a replacement part on the Baja 5T HPI SFL-10MG2 servo, or as an upgrade to the stock plastic servo arm used on the SFL-10 and HPI SFL-MG servos. HPI recommends upgrading to the metal servo gears if upgrading the stock plastic servo arm.Contents:1 piece
The MadMax SUPERGRIP tires have been designed especially for use on tarmac. Even on fine-pored tarmac your car will still find enough grip! (As you can see in our video).On most 1/5 and 1/6 cars the best combination is the use of 60 mm wide front and 80 mm wide rear tires. The Losi 5ive-T Mini should run 60 mm wide MadMax SUPERGRIP tires all around, because the 80 mm wide SUPERGRIP tires are a bit too wide for the Mini body shell.The 80 mm wide MadMax tires are reinforced on the inside of the carcass with a special cross pattern in the tread section and ribs in the outside shoulder.MadMax SUPERGRIP tires are available in the following compounds: (embossed marking on the inside shoulder!)Breite:Soft:Medium:60 mm y1464/01y1464/0280 mm y1464/03y1464/04For running an rc-car on tarmac, the following recommendations apply:The dirtier the track or the colder the weather, the stickier (softer) the rear tires should be.A note for the front tires: 2WD cars should run slightly harder tires in front than in rear.On 4WD cars the same compound front and rear is usually a good choice!Of course, like in full scale motorsport it also applies to the MadMax SUPERGRIP tires that the softer the tire the higher the wear. The medium compound tire lasts significantly longer than the soft version!The MadMax SUPERGRIP has a special on-road tread. These tires have excellent grip even after eating up the tread and can be used after that for a long time as slicks! Some off-road tires knowledge can be found here!
Split aluminium servo lever for more gentle screwing (with a 2.0 mm Allen key) with clamping on the servo output shaft!For servos that have an output shaft with a 17 mm multi-tooth shaft. For our y2006 Top Tuning digital Pro Servo 40 Kg
Mounting holes with 3 mm diameter
If you count the teeth on your servo, you can determine whether this aluminium arm fits your servo. Aluminium servo arms are indispensable for powerful digital servos, such as those used in large-scale models.
Translated with DeepL.com (free version)
Genuine ATOP spare/option part. CNC-machined from 6061 aluminum, significantly stronger and more rigid than any plastic version. Single-sided anodized aluminum servo horn, available in 18t spline version. Three M4 tapped holes for the linkage. 18T fits:Spektrum DBXL-servo SPMS901Contents:1 piece
