Genuine CYS spare/option part. New ballraced digital servo with metal gears. Powerfull servo for steering applications in 1/5 and 1/6 scale cars, can be used for throttle/brake as well.voltage: 6 - 7,2 Vtorque: @ 7,2 V = 30 kg/cm / 6 V = 28 kg/cmspeed: 60° @ 6 V - 0,14 Sek.connector: Graupner-J/R + Robbe/Futabadimensions: 59,5 mm length, 29,2 width, 51,3 mm height154 grammsIdeal size for FG Sportsline and offroad / monster / stadium cars, all Carson / Smartech / Nutech / Conrad offroad or onroad cars and many other largescale cars as well. Digital-Power servo includes the following top equipment: One x double-sided 68 mm long servo horn, with 2,5 mm holes for linkage installation One x sigle-sided 42 mm long servo horn, with 2,5 and 3 mm holes for linkage installationFour x rubber grommets with 3 mm brass sleeves Four x mounting screws 3 x 14 mm Two x mounting screw 3 x 9 mm for the servo horn to the ballraced brass output shaft with Futaba/ds1015 spline sizevery strong 17-spline / 8,75 mm output shaftInstallation note: Always use the supplied rubber grommets and brass sleeves for installation of the Digital-Power servo!#6118/02 is required for FG 2WD offroad and monster cars, radio plate #y0532 for FG 4WD cars.Due to the high power of the Digital Power-Servo care must be taken that all wiring is up to the task. It is also absolutely mandatory to use the provided rubber grommets along with the brass bushing inserts for installation. (Replacement provided rubber and brass bushing: y0750/03)Contents:1 piece
Genuine HT spare/option part. Protects the mated connection to prevent them from coming apart accidentally. Particularly recommended for direct power supply cords, as a tensile load on the cable can remove the link unnoticed and then you would perhaps think of a servo failure in the first place.The small size usually allows the installation even inside the receiver box.Also suitable for securing the connection of the receiver battery; the use of this clip means a big improvement in safety with little effort.Contents:1 piece
Item N° y1101 Servo horn mounting screws, 10 pcsReplacement screws for mounting the servo horn on the servo shaft.Part is delivered in silver or black color from vendor!Choises:y1101/01Fit:Multiplex Jumbo and Power MCFG 6598 Savöx-Servo SC-0251MGFG 6599 Savöx-Servo SC-1256TG Measures: M3 x 8 mmy1101/02Fit:Multiplex RhinoHitec 805 MGHitec 9805 MGFutaba S3152 Measures: M2,5 x 10 mm Torxy1101/03Fit:Futaba und Robbe diverse ServosPlease check the required dimensions! Measures: M2,5 x 6 mm Torxy1101/04Fit:402115 Mega Power-Servo, metal gears Measures: M3 x 10 mm y1101/05Fit:Ace DS1015 Super Torque Digital Servo, y1051 Measures: M3 x 10 mm
CYS S0650, a digital large scale servo with very robust steel gears. It offers a lot of power at good speed. Its a direct fit for cars like Losi 5ive and DBXL, UFRC Growler GX1, FG and so on.Technical data: Operating voltage: 6V-7.4V Operating speed (6.0 V): 0.13 s / 60 degrees Operating speed (7.4 V): 0.11 s / 60 degrees Holding torque (6.0V): 470 Ncm holding torque (7.4V): 539 Ncm Cable: Universal/JR connector, approx. 300mm Gear material: 1st stage brass, all others steel Bearing: 2 x ball bearing Size: 66 x 30 x 56mm Weight: 204 grams Double sided servo arm 68mm length Guide sleeve 4 pieces Mounting screws 4 pieces Mounting screws for servoarm 1 piecesContents:1 piece
Fits most spray cans from many manufacturers.Convert your spray can into a spray gun. The long-lever system of this handle makes using a spray can much more convenient and provides better flow rate control as well.No more dirty hands from paint work.Contents:1 piece
Genuine FG spare/option part. Powerfull servo for 2WD and 4WD 1/5 and 1/6 cars. Ballraced, with metal gears.Technical data:Voltage : 6.0-7.4VSpeed : 0.14s-0.12s/60°Torque: 9-10kgcmDimensions : 40.8 x 20.1 x 38 mmWeight : 56 gContents:1 piece
y2006 Top Tuning Digital pro 40 kg is a digital large scale servo with a very robust metal gears.It offers a lot of power at good speed and has a metal housing with side cooling fins.Its installation dimensions fit directly for FG, Losi, HPI and various other models! Dimensions identical to: Multiplex Rhino - Servo 32 kg FG Mega - Servo ST2605 30 kg Spectrum SPMS904WP 34 kg Spectrum SPMS904HV 18 kg Technical data: Classification: large scale servo Dimensions LxWxH (mm): 59.5 x 29.2 x 55.2 mm Operating voltage: 6 volts / 7.4 volts Torque: (Ncm): 380/400 Speed (sec / 60 °): 0.20 / 0.18 Number of ball bearings: 2 Servo gear: metal gears Seals: 3 (splash-protected) Silicone cable: with universal plug, 300 mm long Weight: 146 grams Brass output shaft 17T spline Content: 1 piece of TopTuning Digital pro servo 40 kg 1 piece double sided servo arm 70 mm total 1 piece of 40 mm single sided servo arm 4 pieces of guide sleeves 4 pieces of rubber grommets 4 pieces of fastening screws
This model is fitted with numerous aluminium parts: front and rear side bulkheads, rockers, engine mount, suspension arm ends...Steel made Uniball sockets all possible enable all adjustments of the front and rear suspensions.The transmission made with a gearwheell drive offers outstanding reliability and smooth operation.Just like all other FG Competition models the FG Formula 1 Competition is the most successful model of the past years. The experiences we gained from numerous competitions have all influenced this version. The FG gearwheel drive which is extremely smooth running and cares for more power reserves. Surely FG Modellsport has created a competitive model for the next years with this version which will seamlessly follow up on the past successes. Highlights Alloy wishbones FG gearwheel drive Alloy rear axle plate FG alloy shock absorbers 04 Ball-bearing alloy servo saver 26 ccm Zenoah-Engine Airbox Tuned pipe Front- and rear brake 5 mm Chassis Lexan body shell Technical description of the FG Formula 1 Competition ki:The undercarriage of the FG Formula 1 Competition is built on an 5mm alloy chassis. All screws at the bottom of the chassis are countersunk.Front and rear axle mounts as well as the engine unit are connected over the complete length of the chassis, therefore we achieved almost the stiffness of a monocoque chassis. The quick fix system of the engine makes a fast changing of the engine possible. The drive to the rear axle is carried out over several easy-running front gearwheels and an FG ball drive at the rear axle. A separate flange bearing holds the clutch bell in order to relieve the crankshaft. Front and rear axle with their various adjusting possibilities as king pin angle, castor a.s.o. consist of alloy delta wishbones below. Solid alloy rear axle plates reduce the wear at the rear axle and give an enormous driving stability. 4 oil-pressure shock absorbers controlled by a pushrod suspension as well as stabilizers guarantee an optimal ground contact.We deliver the chassis selectively with tuning bowden cable brakes for front or respectively rear axle. The model is powered by a high-capacity 26 cm³ engine with airbox and Tuning pipe.Equipment of the FG Formula 1 Competition kitCNC-cut 5mm alloy chassis with lateral carbon fiber inserts, 26 cm³ engine, inlet silencer, Tuning pipe, FG gearwheel drive, ball drive, complete rear and front axle carrier unit with integrated engine quick-fixing device, double alloy wishbone fastenings, lower alloy delta wishbones at front and rear axle, front and rear alloy uprights, ball-bearing servo saver, steering stops, pushrods, 4 oil-pressure shock absorbers with alloy damper pistons, mechanical Tuning brakes at front and rear, stabilizer for front and rear axle, 10mm alloy balls, rear spoiler, polycarbonate body shell, polyamide front spoiler, receiver box, competition tires with tire inserts.We deliver the models as a kit including mounting instruction. The body parts are made of clear polycarbonate for your own painting. FG stickers and writings are enclosed.For the final assembly of the models you need further: radio control system (transmitter, receiver), 1 large steering servos (each approx. 40 - 50 kg), 2 servo for throttle brake (approx. 20 - 30 kg), batteries and charger.These parts are not included and must be supplied or ordered separately when the rc installation option is selected! Includet Zenoah 26cc engine Clear bodyshell and polycarbonate spoiler Mechanical brakesDimensions Length: 960mm Width: 440mm Height: 230mm Wheelbase: 620mm Formular 1 models in action!
Offerset:2 Pairs MadMax Giant Grip tires2 Pairs MadMax rims2 Pairs MadMax inlays2 Pairs / 4 pieces adapter TT1020/01GIANT GRIP 190 x 70 with black colored MadMax Extreme rims, 20-fold screwed, very tough, with 24 mm hex drive and reinforced beadlock rings for Losi 5ive-T and Desert-Buggy XL as well as all HPI Baja 5 B/T cars.The GIANT GRIP provides giant traction through 96 about one cm² wide and 5 mm high strong lugs, getting ample grip even on loose surfaces like sand and soil.Due to the extreme strain caused by the GIANT GRIP tires the MadMax rim with reinforcement ring had to be optimized once more.The set consists of four tires, including tire inserts and MadMax EXTREME rims and 4 pieces adapter wheel nuts TT1020/01.The GIANT GRIP tires come with strong special tire inserts which allow to transfer the power without canting, even on heavy cars like the Losi 5ive-T.Dimensions:Outer diameter: 190 mmTire width at bead 70 mmTread width 80 mmReinforced 24 mm hex wheel driveThe video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!TT1020 Top Tuning Adapter wheel nutGenuine TopTuning spare/option part.These adapter nuts, manufactured from billet 7075 aluminum allow for easy and precise installation of all MadMax, HPI and Losi tires and rims on the Traxxas X-Maxx. For the best result possible, nut and adapter are manufactured as a one-piece unit.It should be noted that the wide rims can be used on the rear axle only. On the front axle they would limit the steering angle by grinding on lower a-arm and steering rod.Traxxas has microencapsulated the wheel shafts of the X-Maxx to secure the wheel nuts. Like any thread locking compound this is not for eternity. After several tire changes the use of a normal screw locking compound is advised, we recommend it "y0113 / 01 medium strength".The dimensions of the nut are specifically designed for use with MadMax, current HPI and Losi rims. Rims from Losi 5ive have slightly different dimensions in the hub area. This is meaningless on the large LOSI or HPI wheel adapters. With the smaller and shorter wheel nut thread of the X-Maxx wheel shafts you cannot compromise. Therefore there are also special nuts for the Losi rims/wheels available at our options menu.However, somewhere in the past, the injection moulds for the HPI rims were slightly modified in the hub area. As part of that job the bore diameter has probably been slightly increased. Therefore, the use of older rims in combination with the adapter nuts makes it necessary to increase the rim bore a little bit.Due to repeated requests for use: these wheel nuts replace the stock wheel nuts when installing the wheels!Contents:4 pieces
€149.90*
This website uses cookies to ensure the best experience possible. More information...