6417/09 FG Slick tires S/63mm 1:6, glued, 2 pcs.

Genuine FG spare/option part.Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Measures:Diameter: 145 mmWidth: 80 mmRim with 18 mm square drive.

Genuine rc-car-online spare/option part.The optimal parking lot or race tires for your FG Racetruck model.Type Width Outer diameterFront 64 mm 153 mmRear 78 mm 153 mmGlued on original FG-Racetruck rims (rear tire with extension to the inside), incl. foam rubber insert,FG rim with 18 mm square drive and reinforcement ring.Attention: From experience we warn against using rims and extensions from another manufacturer.Since the Mammoth tires provide a very good grip, the rim and bonding are extremely stressed. Due to the high torque load in relation to the bonding of tires on large models, an occasional check in this regard and possibly a repair of the bonding (y0067) is inevitable.As a recommendation:The dirtier the track or the colder the temperature, the softer the rear tire should be.Reference for the front tire: With 2WD models this should be one to two stages harder than the used rear tire. On 4WD models, a tire combination with the same shore hardness front and rear is often good to drive.Of course, with Mammoth Supergrip Racetruck tires, the softer the tire, the higher the wear.The Mammoth Supergrip Racetruck tires have a special onroad tread. Whereby these still have an optimal grip after the wear of the tread, and can still be driven for a long time.

Genuine FG spare/option part. Inclusive tyre inserts.Dimensions:Diameter: 145 mmWidth: 63 mmContents:2 pieces

Genuine Hitec spare/option part.Waterproof Power IP67 for large models and many industrial applicationsServo HS-1100WP is the most powerful and 100% waterproof servo Hitec large assortment! Thus, it is ideally suited for industrial applications and also for XXL large-scale models. Equipped with a hand-brush motor for maximum reliability and durability, and which protects from the full milled aluminum housing perfectly against electromagnetic interference. Another special course (not programmable) to call the virtually indestructible steel gears and a digital servo electronics IP67 classification.The Servo HITEC HS-1005SGT delivers maximum and constant performance and with its data also a favorite for industrial applications such as UAV, robotics and special effects. Technical data:Width: 33 mm Height: 73 mm Length: 64 mm Weight: 0340 kg Power Type: Mega Features: operating voltageFrom 11.1 to 14.8 volts, Amendment leads possible (Optional) Engine type servos: brushed Transmission: steel Operating voltage in V: 11.1 to 14.8 volts Actuating time s / 60 ° at 11.1 volts: 0:26 Setting time s / 60 ° at 14.8 volts: 12:19 Torque in kg cm at 6.0 volts: 84 Torque in kg cm at 7.4 volts: 110 Teeth: Mega Ball bearings: Yes, 2 times MR148 Waterproof: Yes Flight recommendation: YES Recommendation Heli: YES Recommendation Car: YES Recommendation boat: YES Temperature range: -20 ° to 60 ° CFeatures:Highest force Enormous holding power Indirect long-life potentiometer, 1 million cycles Steel gears Bearings, 2-MR148 Aluminum housing Separate signal and power supplyContents:1 piece

Suitable for all FG front uprights. The use of this front axle prevents a pressing and jamming of the inner ball bearing rings when tightening the wheel. Suitable for square wheel driver 9,5mm and 14mm.

Genuine FG spare/option part. The following items are required for completion: electric motor, ESC, steering servo, radio system, body mounts, body, LiPo driving batteries and charger.