6077/08 FG Spacer bushing for rear upright
€4.90
Available
Product information "6077/08 FG Spacer bushing for rear upright"
Only suitable with standard size ball bearings.
Dimensions:
- Length: 10 mm
- Outer diameter: 11 mm
- Inner diameter: 8 mm
Contents:
- 2 pieces
Login
Customers also bought
Genuine FG spare/option part.The installation of these spacer bushings between the ball bearings in the uprights allows you to tighten the wheel nut strongly. Suitable for all FG plastic and alloy uprights.Dimensions:Outer diameter: 11 mmWidth: 7 mmInner diameter 8,22 mmContents:2 pieces
Suitable for all FG front uprights. The use of this front axle prevents a pressing and jamming of the inner ball bearing rings when tightening the wheel. Suitable for square wheel driver 9,5mm and 14mm.
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)12 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 12 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Content:2 pieces
Genuine FG spare/option part.Dimensions:6 x 8 x 7,5 mmContents:6 pieces
Replacement part for Mecatech twin piston hydraulic brake.
Replacement part for Mecatech twin piston hydraulic brake.
Customers also viewed
Genuine FG spare/option part.Part is delivered in silver or black color from vendor!Set includes:15 x Torx body screws M3 x 10 mm15 x Washers15 x M3 Hexagon nut
Fits all FG offroad / monster and stadium models (except Leopard 2010 up). Also for FG Formula 1 and Race Truck models. The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins. The GPM ball drives can be partially mixed with FG parts. The heads of the GPM driveshafts fit into FG differential cups or wheel shafts.The opposite combination, i.e. FG shafts in GPM differential cups or wheel shafts does not always fit. We had tests where some FG shafts fit neatly, but due to slight tolerances others who did not fit into the very same cups/shafts. For this combination, we can not guarantee compatibility! Dimensions: Length 96.5 mm
Genuine FG spare/option part. Corrosion resistant and 40 % less weight compared to steel.Contents:2 pieces
Genuine FG spare/option part.For Evo models with new servo saver 1212 and lower installed servo plate.Contents:2 pieces
Genuine FG spare/option part.The installation of these spacer bushings between the ball bearings in the uprights allows you to tighten the wheel nut strongly. Suitable for all FG plastic and alloy uprights.Dimensions:Outer diameter: 11 mmWidth: 7 mmInner diameter 8,22 mmContents:2 pieces
Alloy rear axle conversion kit for all FG 1/5 Sportsline cars except Formula 1 and Race Truck.The set includes:- rear plate- differential mounts- riser plates- lower a-arms- upper a-arms- installation hardware.Please note: must use inge pins 6075 instead of 6073!