Product information "10455 FG Polyamide front spoiler for F1"
Genuine FG spare/option part.
Solid front spoiler produced in impact resistant polyamide for the FG Formula 1 models. The complete front spoiler and side parts are manufactured in one piece. The ground colour is black and can be painted over restrictively.
This front spoiler is specially suited for the use at competitions. Standard equipment of F1 Competition.
Contents:
1 piece
0 of 0 reviews
Average rating of 0 out of 5 stars
Leave a review!
Share your experiences with other customers.
Login
No reviews found. Share your insights with others.
Formular 1 tire chart from the current series divided into 3 categories 1) Parking lot / hobbyThe durability of the tire is the main focus here.2) Race track / hobbyHere you will find the tire that offers a compromise of durability and performance.3) Race track / competitionHere the racer will find the tires for best lap times on a race track and to win races.Note:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability. Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!Genuine GRP spare/option part. This pair of Tyres have the following use indications:HIGH GRIP situation for very clean trackHIGH GRIP situation for big asphaltHIGH GRIP situation for high temperaturesThis pair of Tyres have the following technical features:REVO Grooved profile for the maximum traction and the maximum lateral gripGrooved profile studied to maintain the tyre surface alway clean from rubber murbleM1 ExtraSoft compound exclusively developped for model tyresInside belt flexible but very strong, vulcanized directly together with tyre compoundInsert foam with special material for high temperatures, for maximum stability and high drive precisionSpoked wheel moulded with special material for high temperatures for maximum grip and stabilitySpecial gluing system 100% guaranteedThe main sizes for this tyre are:WHEEL fixing with square: 18 mmTYRE outside diameter: 137 mmWHEEL inside diameter: 100 mmTYRE total width: 64 mm Contents:2 pieces
Formular 1 tire chart from the current series divided into 3 categories 1) Parking lot / hobbyThe durability of the tire is the main focus here.2) Race track / hobbyHere you will find the tire that offers a compromise of durability and performance.3) Race track / competitionHere the racer will find the tires for best lap times on a race track and to win races.Note:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability. Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!Genuine GRP spare/option part. This pair of Tyres have the following use indications:HIGH GRIP situation for very clean trackHIGH GRIP situation for big asphaltHIGH GRIP situation for high temperaturesThis pair of Tyres have the following technical features:REVO Grooved profile for the maximum traction and the maximum lateral gripGrooved profile studied to maintain the tyre surface alway clean from rubber murbleM1 ExtraSoft compound exclusively developped for model tyresInside belt flexible but very strong, vulcanized directly together with tyre compoundInsert foam with special material for high temperatures, for maximum stability and high drive precisionSpoked wheel moulded with special material for high temperatures for maximum grip and stabilitySpecial gluing system 100% guaranteedThe main sizes for this tyre are:WHEEL fixing with square: 18 mmTYRE outside diameter: 137 mmWHEEL inside diameter: 100 mmTYRE total width: 74 mm Contents:2 pieces
Servo direct power supply cable, 1 pce.With this cable the servos get their current directly from the battery without straining the receiver circuit board.Silicone insulated wires with 0.5 mm² cross section
Genuine FG spare/option part. Specially produced small hexagon nuts with left-hand thread to fix the steel ball-and-socket joints with the wishbone thread rods M7.Maße:Hex size: 8 mmThickness: 3 mmPart is delivered in silver or black color from vendor!Contents:2 pieces
Genuine FG spare/option part. Solid steel ball-and-socket joints with 4mm boring in the steel ball and M7 left handed thread. Clearance- and maintenance-free. Useable for the F1 front and rear axle instead of the plastic ball-and-socket joints 10mm 10027 and 10027/07.For mounting the wishbone thread rods M7 and hexagon nuts M7 with left-handed thread 10437, 10437/01 are necessary.Dimensions:A = 4 mmB = M7 l/hC = 14.5 mmD = 16.5 mmE = 45.7 mmContents:2 pieces
Genuine FG spare/option part. Specially produced small hexagon nuts with right-hand thread to fix the steel ball-and-socket joints with the wishbone thread rods M7. Dimensions:Hex size: 8 mmThickness: 3 mmPart is delivered in silver or black color from vendor!Contents:1 piece
Retrofitable bowden cable disk brakes for Formula 1 Sportsline and Competition models. Essentially improved brake power compared to the standard brake, sensitive adjustment.
Clutch flange bearing for the F1 clutch bell. The clutch bell of the engine is guided through the sparate bedding of the flange bearing. Additional the clutch bell runs centrical to the clutch blocks. The mounting of the flange bearing is only possible in connection with the engine quick fix system and the short F1 clutch bell. Suitable for the F1 Sportsline in combination with Solo and Zenoah engines. Standard equipment of F1 Competition.Shaft size length x diameter: 45 x 10 mm
Genuine FG spare/option part. Solid steel ball-and-socket joints with 4mm boring in the steel ball and M7 right handed thread. Clearance- and maintenance-free. Useable for the F1 front and rear axle instead of the plastic ball-and-socket joints 10mm 10027 and 10027/07.For mounting the wishbone thread rods M7 and hexagon nuts M7 with right-handed thread 10437, 10437/01 are necessary. Dimensions:A = 5 mmB = M7C = 14.5 mmD = 16.5 mmE = 45.7 mmContents:2 pieces
The FG Off-Road Buggy WB535 is presented with a longer wheelbase and a pleasant design. All-wheel-drive, completely mounted ready-to-drive, combined with the open Off-Road Buggy body shell with metal roll cage and gigantic Off-Road rims with low-profile knobbed tires.The body shell is standard unpainted. Equipped with a 26cm³ engine the Off-Road Buggy is aggressive and also a tremendous jumper. The 35 mm wheelbase extension results in a higher tracking stability. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Equipment of the modelAngled 4 mm, alloy chassis, completely covered belt drive, two differential gears at front and rear axle with hardened bevel gearwheels, closed front axle housing, front bumper, double wishbones at front and rear axle, gear brake, adjustable right/left thread rods at the track rods and at the front and rear wishbones, front uprights with steering stops, gearwheels made of case-hardened steel, completely ballbeared, four large-volume oil-pressure shock absorbers, receiver box.According to side rails and the closed body shell the Off-Road Buggy Buggy is almost protected against dirt from underneath. The two-parts body shell is made of polycarbonate, the rear spoiler is made of impact resistant polyamide. Driver´s coverage and roll cage parts are made of aluminum. The giant low-profile knobbed tires are glued on black rims.The model is equipped with a powerful 26cm³ (series) combustion engine with ready-for-use oiled air filter. The engine runs with normal 2-stroke petrol-oil mixture (available at every patrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-stat system the engine can be started without any difficulties. The RTR version is delivered with installed and preset radio control system and rechargeable batteries. To complete the non-RTR version all popular servos and radio control systems are suitable.The pictures may display the car with some optional items which are not included, like bed-mounted rollbar, lights, front bumper or mirrors. These items can be added in the drop down menus.Measures:Length: 770 mmWidth: 480 mmHeight: 280 mmWheelbase: 535 mmWeight: 10,8 kg
Genuine FG spare/option part. 1:/6 Off-Road Buggy tires, medium, glued on FG Off-Road buggy-rim white. Outer Ø 175 mm, width 80 mm, Suitable for the FG cars Marder, Off-Road Buggy, Beetle and Monster cars with 18 mm square wheel drive. Suitable for other 1/6 cars as well: please check the wheel drive regarding this matter. When the wheel change causes a significant change of the tire's outer diameter, adapting the gear ratio is recommended.Contents:2 pieces
Trendy body shell for nearly all 1/5 scale Formular 1 models.The body shell comes as a thermoformed and molded "plate" (with protective sheet) which you have to cut on your own.
Completely mounted, with a 26 cm³ combustion engine and final speed of almost 100 km per hour, what else would you want?A further additional improvement is the installed front disk brake. A clear polycarbonate bodyshell is included.Quality and high-class equipment to a sensible price.Technical description of the Formula 1 Sportsline chassis:The undercarriage of the FG Formula 1 is built on a high-strength 5 mm alloy chassis. All chassis borings (screws) are countersunk. The front and rear axle with their various adjusting possibilities as king pin angle, trailing effect etc. consist of double delta wishbones. The double delta wishbones of the rear axle are supported by additional track rods which enable you a very fast set-up. All adjustments can be made without a dismounting of parts according to the fixed wishbone threaded rods with right-/left-handed thread.The model is equipped with 4 alloy oil-pressure shock absorbers. The push-rod suspension ensures the transmission between single wheel suspension and shock absorber.We deliver this chassis with a powerful 26 cc combustion engine. The engine's power is transmitted over a four-block Teflon clutch on a synchronous belt drive. This synchronous belt drive is also designed for a higher driving power. The BBS wheels and the tires are copies of the big models. All rotating parts are supported by ball bearings.The construction of the Formula 1 chassis is not identical with the other 1:5 scale FG models such as Merc. C-Class, Race Truck a.s.o. and therefore it can?t be converted into or from these models by a conversion kit.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Dimensions:Length: 960 mmWidth: 440 mmHeight: 230 mmWheelbase: 620 mmFormular 1 models in action!
Highlights News 2025 Tuning aluminium lower wishbones, one-piece (front and rear) Tuning chassis plate black anodised and milled Tuning milled aluminium rear axle linkage for toe-in adjustment Perforated tuning clutch bell Side flaps on the rear spoiler in carbon fibre
Highlights Formel 1 Competition- This model is fitted with numerous aluminium parts: - front and rear side bulkheads, rockers, engine mount, suspension arm ends...Steel made Uniball sockets all possible enable all adjustments of the front and rear suspensions.The transmission made with a gearwheell drive offers outstanding reliability and smooth operation.Technical description of the FG Formula 1 Competition :The undercarriage of the FG Formula 1 Competition is built on an 5mm alloy chassis. All screws at the bottom of the chassis are countersunk.Front and rear axle mounts as well as the engine unit are connected over the complete length of the chassis, therefore we achieved almost the stiffness of a monocoque chassis. The quick fix system of the engine makes a fast changing of the engine possible. The drive to the rear axle is carried out over several easy-running front gearwheels and an FG ball drive at the rear axle. A separate flange bearing holds the clutch bell in order to relieve the crankshaft. Front and rear axle with their various adjusting possibilities as king pin angle, castor a.s.o. consist of alloy delta wishbones below. Solid alloy rear axle plates reduce the wear at the rear axle and give an enormous driving stability. 4 oil-pressure shock absorbers controlled by a pushrod suspension as well as stabilizers guarantee an optimal ground contact.We deliver the chassis selectively with tuning bowden cable brakes for front or respectively rear axle. The model is powered by a high-capacity 26 cm³ engine with airbox and Tuning pipe.Equipment of the FG Formula 1 Competition CNC-cut 5mm alloy chassis with lateral carbon fiber inserts, 26 cm³ Zenoah engine, inlet silencer, Tuning pipe, FG gearwheel drive, ball drive, complete rear and front axle carrier unit with integrated engine quick-fixing device, double alloy wishbone fastenings, lower alloy delta wishbones at front and rear axle, front and rear alloy uprights, ball-bearing servo saver, steering stops, pushrods, 4 oil-pressure shock absorbers with alloy damper pistons, mechanical Tuning brakes at front and rear, stabilizer for front and rear axle, 10mm alloy balls, rear spoiler, polycarbonate body shell, polyamide front spoiler, receiver box, competition tires with tire inserts.For the final assembly of the models you need further: radio control system (transmitter, receiver), 1 large steering servos (each approx. 40 - 50 kg), 2 servo for throttle brake (approx. 20 - 30 kg), batteries and charger.These parts are not included and must be supplied or ordered separately when the rc installation option is selected! Includet Zenoah 26cc engineAirboxPipe Clear bodyshell and polycarbonate spoiler Mechanical brakesDimensions Length: 960mm Width: 440mm Height: 230mm Wheelbase: 620mm Formular 1 models in action!
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).