13 products found for "fg_1040_08"

rc-car-online - Home

1040/08 FG Spacer large for Evo 2020-2020.2

Genuine FG spare/option part. for FG Evo 2020 and 2020.2 modelsContent:3 pieces

€27.40*

1040/09 FG Spacer small for Evo 2020-2020.2

Genuine FG spare/option part. for FG Evo 2020 und 2020.2Content:3 pieces

€16.70*

1040/06 FG Spacer tube, 13x43 mm for Evo 04 - 08

Genuine FG spare/option part. For 1040/05 alloy gear flange-engine mount. The tube goes between the bearings and prevents binding them.Contents:1 piece

€5.90*

1040/01 FG Engine mount for Evo 2020.2

Original FG Ersatz-/Tuningteil.Inhalt:1 Stück

€99.90*

1040/07 FG Bell mount small for Evo 2020-2020.2

Genuine FG spare/option part. for FG Evo 2020 and 2020.2 modelsContent:1 piece

€64.80*

6040/08 FG Alloy layshaft bearing mount Evo 2020

Genuine FG spare/option part.Adjustable layshaft bearing mount; for adjusting gear play between layshaft and differential gear when running fine pitch gears.Contents:1 piece

€87.90*

10403 FG Tuned pipe F1 - set

New developed Tuning pipe with significanty more power due to the longer manifold and bigger volume. To mount this Tuning pipe the battery 6543/1 is necessary.

€244.95*

10400 FG F1 tuning pipe

For install you need FG Exhaust FG 10215.

€165.20*

10401 FG Steel manifold for tuned pipe F1 - 1pce.

Very strong steel manifold, for use with Formula 1 Sportsline tuned pipe and tuning pipe 10400 only.

€68.20*

LOS251040 Losi Rear bumper brace MTXL

Genuine Losi spare/option part.Contents:1 pieces

€29.99*

y1040 T-connector for hydr. brake system - 1 pce

T-connector for all hydraulic brake linings with a outside diammeter of 4mm. e.g Colari, Magura II and Mecatech.

€14.90*

HW30104002 Hobbywing Ezrun MAX4-HV ESC Sensored 300 Amp, 6-12s LiPo, BEC 10A

The Ezrun Max4 controller is suitable for particularly large 1:4 and 1:5 scale models. This controller is ideal for use in any of these models, whether heavy-duty off-roaders or trucks. It is the ideal choice for high-end models that are subject to high demands or are operated aggressively. Despite the enormous size, care was taken to use high-quality and, above all, durable materials in the construction. This can be seen, for example, in the fact that the Max4 controller is excellently protected against dust, water and similar external influences. The electronic switch is also optimally protected against damage that could otherwise occur during a normal ride. In addition, the Ezrun Max4 has a built-in super high-current BEC that can provide a maximum output power of up to 25A. The output voltage can therefore be switched between 6V, 7.4V and 8.4V. The high-current BEC was developed to supply the latest high-current servos with sufficient power on request and thus to be able to precisely control the appropriate large models. Features - Super-strong switch mode BEC with a constant current of 10A, instant 25A and the ability to switch between 6, 7.4 and 8.4V - Fireproof circuits to protect the battery connector - Additional built-in protection mechanisms: undervoltage, overheating, signal loss, ... - Versatile programmability - Real-time data recording Technical data: Current (continuous/short) 300A / 2000A Motor type: Sensor/sensorless brushless motors Motor limit: 12S LiPo: kV <= 600 (70125 size) LiPo cells: 6-12S BEC: 6V / 7.4V / 8.4V with 10A (switchable) Fan: Yes (supply via built-in BEC) Programming input: Fan / PRG input Programming: LED programming card, LCD programming box, OTA programming module Size: 125x85x61.7mm Weight: 775.4g Application: 1/4 and 1/5 Heavy Duty-Off-Road, Trucks

€335.00*

TT1040 Top Tuning 24 mm hex wheel drives for Losi Super Baja Rey / 2.0 and Super Rock Rey / plastic spindles

Genuine Top Tuning spare/option part.TopTuning 24mm hex wheel drives are required if you want to run wheel combos with the standard 24mm hex drive (such as Losi 5ive-T/B; DBXL; HPI-Baja etc.!) on your Losi Super Baja-Rey and Super Rock Rey.The stock Super Baja-Rey / Super Rock Rey20 mm hex drives (# LOS252077) will be swapped for the TopTuning 24 mm version. No additional parts are required for installation of the 24 mm hex wheel drivers. The Losi Super Baja-Rey's fake brake discs and calipers must be removed prior to assembly.Attention: For the attachment of the wheels you also need wheel nuts with M18x1.5 thread (i.e. AT-5T004), which are also offered in our shop's option menu!Please note: The adapters only fit in combination with the standard plastic steering knuckles or wheel bearing carriers. The aluminium versions have a slightly larger bearing distance, which then prevents the drive pin from being fitted.As already mentioned in the Losi instruction manual, the gearing should be adjusted depending on terrain and tire tread.Depending on tire size the rear of the fender wells will need some cutting.Please note: the wide rear wheels from MadMax or HPI do not fit!This applies in particular to aggressive tread large diameter off-road tires and demanding terrain. In this case we recommend the profile regraded, nitrided 15T pinion # TT1021/07 from the TopTuning.Weight per piece 28 grams (original LOS25077 weighs 23 grams).Contents:2 pieces of 24 mm hex wheel drives, machined from 7075 aluminum2 pieces of hardened drive pins 3x23,8 mm

€24.90*

13 products found for "fg_1040_08"

Filter products

rc-car-online - Home