50040050 Lightscale alloy rebound gauge, black, 1 pce.
€27.90
Available
Product information "50040050 Lightscale alloy rebound gauge, black, 1 pce."
Those are usually put on 10mm support blocks and beeing measured their droop with a special tool. The Lightscale ride height gauge (50160200) is a droop gauge as well and will do the job for you.
Login
Customers also viewed
Genuine FG spare/option part.To measure toe-in and to adjust the rear wheels. Only in connection with inclination-goniometer 8540. With this measuring bench you can only measure one side, to measure the second side change the side. Suitable for all FG models except Formula 1.Contents:1 piece
Shock absorber oil for Mecatech Klick-Shocks in various viscosities, 50ml.1 pieces, please selectViscosity of silicone oil at various temperatures.
Content: 50 Milliliter (€250.00 / 1000 Milliliter)
Item N° 50353011Support Blocks for the Lightscale Droop Gauge front, 1 pce.This is an Alloy Support Block anodized in black colour with 30mm height.The Support Block is manufactured as a rectangle and so can used a 30mm, depending on which side you choose.The front block uses a single point of support while the rear one comes with two of those. Due to this 3 point support it is assured that even a little tweak in your chassis (none of them is 100% straight) will not affect the result of your measurement. Remove the wheels and tyres from your car and put the car onto the support blocks. Ideally the rear block is positioned to the back of car and the front one just where the servo saver is fixed to the chassis. The car is now propped on the support blocks safely and cannot bounce. Please make sure that no dirt or rubber is trapped between the Support blocks and the chassis.Now you can easily and correctly measure the droop of each axle and adjust the cars` tweak.To do so please use the Lightscale Droop Gauge (50835400)The use of Lightscales` Droop Gauge Support Blocks prevents incorrect measurements and therefore is absolutely reliable. Measurements which are done using a flat surface where the chassis is resting on, like you would use in the pits are usually incorrect due to a slightly tweaked chassis because dirt underneath the chassis will falsify the measurement and lead to a irregular setup. The use of Support Blocks which are based on 4 support points will result in the same incorrect results and downgrade the performance of your car which is why we 100% recommend the use of our support block because as racers ourselves we know all about the problems you may face.
Original FG GT 360 body parts, without rear part !!! Scope of delivery and equipment see photos. Included in delivery are main part, front spoiler and rear spoiler. Rarity !!! for the 530 mm wheelbase Width 400 mm. Length 790 mm Height 220 mm
A nice tool to create clean circular cuts in Lexan bodies. Adjustable for diameters from 10 to 150 mm. Storage compartment with six blades.Inhalt:Circle cuttersix replacement blades
Genuine Top Tuning spare/option part.TopTuning 24mm hex wheel drives are required if you want to run wheel combos with the standard 24mm hex drive (such as Losi 5ive-T/B; DBXL; HPI-Baja etc.!) on your Losi Super Baja-Rey and Super Rock Rey.The stock Super Baja-Rey / Super Rock Rey20 mm hex drives (# LOS252077) will be swapped for the TopTuning 24 mm version. No additional parts are required for installation of the 24 mm hex wheel drivers. The Losi Super Baja-Rey's fake brake discs and calipers must be removed prior to assembly.Attention: For the attachment of the wheels you also need wheel nuts with M18x1.5 thread (i.e. AT-5T004), which are also offered in our shop's option menu!Please note: The adapters only fit in combination with the standard plastic steering knuckles or wheel bearing carriers. The aluminium versions have a slightly larger bearing distance, which then prevents the drive pin from being fitted.As already mentioned in the Losi instruction manual, the gearing should be adjusted depending on terrain and tire tread.Depending on tire size the rear of the fender wells will need some cutting.Please note: the wide rear wheels from MadMax or HPI do not fit!This applies in particular to aggressive tread large diameter off-road tires and demanding terrain. In this case we recommend the profile regraded, nitrided 15T pinion # TT1021/07 from the TopTuning.Weight per piece 28 grams (original LOS25077 weighs 23 grams).Contents:2 pieces of 24 mm hex wheel drives, machined from 7075 aluminum2 pieces of hardened drive pins 3x23,8 mm
Item N° 8539/01 Measuring bench 740mm for F1 - 1pce.Allows a measuring of toe-in and adjusting of the rear axle without changing the side. For an optimal usw you need 2 . Only suitable for Formula 1.