AREA-BJ035/05 Replace Epoxy plate for BJ035

Medium firmness molded tire inserts with shaped shoulders and recesses to match the beadlock fittings.The medium shore hardness compound of the green colored top quality tire inserts provides optimal support for the tire's shoulder and allows for perfect rolling characteristics of the tire. The perfect tire insert for the HPI-Baja 5B series with 170 mm tire diameter is available in two widths.Fits 10-spoke GPM-racing aluminum rims (Losi / HPI) and MadMax rims as well. Applications:for 60 mm tire width: # y1323/01for 80 mm tire width: # y1323/02

Genuine GPM spare/option part.Tires for a solid to medium terrain.Contents:2 pieces

Genuine HT spare/option part. After-Run is a performance enhancing preservation, which ensures that the engine starts properly, even after a long time (winter break) storage. Added to the fuel it keeps the fuel system clean.Among other After-Run conserves the diaphragm of the Walbro carburetor!For long term storage (i.e. during winter!) "vital" for the carburetor diaphragms!For 23 to 32 cm³ engines like Zenoah, Chung Yang, PT, Losi, HPI a.s.o.It binds water in the fuel, particularly important when the engine is not run regularly or after wet races. After-Run improves engine performance, ensures better combustion, removes debris and residues. Simply add the content of the bottle to 5 litres of fuel.Contents:1 piece / 20 ml

The spark plug tester wiil be put in line between the spark plug in the engine and the spark plug cap. When the spark plug is in good working order, pulling the recoil starter will produce a spark easily visible in the clear section of the tester (see video!).

Original TopTuning spare/option part. Carburetor heat sink for all Zenoah/CY/HPI/Losi and PT-Smartech/Carson engines.Fits all Walbro 603/813/990/771/527/1107 carburetors as well as all Smartech/Carson PT engine carburetors and many more!The TopTuning carburetor heat sink counteracts the notorious vapor lock at high engine temperatures.In fact all current large scale engines have a special adaptor for the thermal insulation of the carb (isolator) to keep the carb as cool as possible, so that the fuel does not form bubbles due to heat transfer from the cylinder. And without this isolator the gasoline would literally cook after a short operating time and therefore the engine would receive a leaner mixture. The much feared lean-out until the engine stalls is inevitably.Unfortunately, even a special isolator is often insufficient at higher ambient temperatures or when the engine is subjected to higher loads, e.g. in racing. In such scenarios the better heat dissipation of the Top Tuning carburetor heat sink contributes to the solution of the problem.The easy to install heat sink, requires a considerable manufacturing and milling effort and fits easily to all common 1:5/1:6 large scale cars, such as FG, Mecatech, Smartech/Carson, HPI, Losi, etc..For installation in FG 4WD cars the rear cross member # 66212 must be modified.Attention: the Allen head screw is an imperial size and therefore not compatible with metric Allen wrenches! Available in our options menu Content: Carburetor heat sink 1 x Allen head screw #8-32 x 5/8" (for Walbro carbs) 1 x washer 4 mm

This reed valve system converts a normal piston-port engine into a reed valve engine. It offers the advantage of increased intake duration for a better charge for more power. As a positive side effect no fresh gas loss occurs during the downward movement of the piston because the membranes close this path.The reed valve block replaces the usual stock insulator. To use the advantage of the reed system, it is necessary to modify the piston skirt on the intake side. Depending on the engine it is advantageous for best results, to slightly match the cylinders intake port to the Epoxy insulator plate at the bottom of the reed valve system. Both steps are described in the installation instructions for Zenoah and Chung Yang engines. Our thanks for these instructions go to our customer Thomas Hoenicke.Note: For the time being the epoxy insulator plate must be slightly reworked to fit a G320 Zenoah engine. The manual has been written with the conversion of a G320, the affected area for modification is therefore shown.The unit is 24.5 mm high.