Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece

Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)9,5 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 9,5 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces

Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)12 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 12 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Content:2 pieces

Alloy rear uprights, with replaceable hinge pin bushings.Fits FG and Carson/Smartech Attack, Attack Evo, Gas Blaster, Gas Devil, Super Attack, CRT, CRT 4x4, CPT, Uno, Monster Truck, Pick Up, Beetle and C5.The bearing bushings and bearings should be glued in place, as they have minimal play.One each lefthand and righthand version.Please note: for the installation of all popular disc brakes, we recommend: y6479

Genuine HT spare/option part.Rear alloy damper plate with several adjustment possibilities of the shock absorbers. Replacement for FG plastic rear shock tower FG 7072/01Please note: When installing in combination with plastic diff mounts you should insert a-arms with hinge pins before bolting together rear plate and diff mounts.Content:1 pieces

Genuine HT spare/option part. Suitable for all FG 2WD and Smartech/Carson 2WD models except Evo 04/Competition 07/EVO 07 and Formula 1. Content:2 piece

Genuine FG spare/option part. The set will shipped without gear carrier plate. Contents:1 set

Genuine HT spare/option part.Alloy upright for a ball fastening at the upper wishbone. Adjustable at the lower wishbone (hinge pin), too. Fits the rear axle of all FG and Carson / Smartech 1/6 scale cars.Comes with adjustment clips and grub screws for the hinge pins included.Dimensions:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 25 mm Contents:2 pieces

Alloy upright for a ball fastening at the upper wishbone. Adjustable at the lower wishbone (wishbone pin), too. Fits the rear axle of all FG offroad cars (2WD and 4WD) and all Carson / Smartech cars.Content:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 25 mm

For the secure installation of driveshaft boots.

Genuine HT spare/option part.Rear upper alloy wishbone with droop stop. Replacement for plastic wishbone FG 6074/02.Will also fit the following Carson/Smartech cars:Onroad chassis C5, Attack, Super Attack, Gas Blaster and TouaregCarson Comanche, Attack Evo, CRT + CPT when installedwith 75 mm turnbuckle y0988Comes with 2 M8 low height nuts included. Contents:2 pieces

Genuine Mecatech spare/option part. The new Mecatech Big Bore shock absorbers with piggy back volume compensation reservoirs use normal silicone oil. The increased diameter in combination with the separate volume compensation via a floating piston of the new MecaTech Big Bore shocks allows for a very constant driving. This results in improved traction and optimized handling.The Big Bore shocks fit most 1/5 scale onroad cars.The outstanding craftsmanship guarantees a perfect seal; the shocks come w/o springs. The Big Bore shocks feature aluminum shock ends with replaceable bushings. Technical specifications: Total length: 120 mmDistance of mounting holes: 110 mm center/centerMounting hole diameter: 4.10 mmThickness of shock ends: 6 mmMax shock/spring travel: 30 mmWeight without oil: 46 g eachWeight without oil with spring: 68 g eachRecommended silicone oil:Mecatech recommends silicone oil with a viscosity of 6,000 to 8,000 for the front axle and 3,000 to 5,000 for the rear.Content:1 set

Genuine HT spare/option part.New designed rear lower alloy wishbone with replaceable guide bushes.Suitable for all FG 1:5 models with a width up to 400mm.Does also fit Carson Attack and Super Attack (not Evo!), C5, Smartech Spider and Ranger cars; also for Reely R5 and Big Pyro when used in combination with turnbuckle 6100/04.Please note: must use hinge pins 6075 instead of 6073!Scope of delivery:1x Alloy wishbone1x Socket head cap screw: 4 x 20 mm1x Socket head cap screw: 3 x 14 mm1x Socket head cap screw: 4 x 25 mm1x Washers steel 4,3 mm1x self-locking hexagon nut M42x hex nut M8 l/h thread4x Bearings with flangeContents:1 piece

Genuine HT spare/option part.Quick change clips for installation and de-installation without tools, galvanic zinc plated.Spring steel, hardened and tempered to 1450 to 1600 N/mm² tensile strength.Available for 4, 5 and 6 mm shafts.Contents:10 pieces

Alloy rear axle conversion kit for all FG 1/5 Sportsline cars except Formula 1 and Race Truck.The set includes:- rear plate- differential mounts- riser plates- lower a-arms- upper a-arms- installation hardware.Please note: must use inge pins 6075 instead of 6073!

Genuine HT spare/option part. Hardened pins made of 100Cr6 steel for driveshafts, differentials, wheel drives and similar applications. Pack of ten. Sizes available:y1345/01: 4 x 18 mm, e.g. for Losi 5ive-T/Mini and HPI Baja differentials or HPI Baja layshafty1345/02: 4 x 20 mm, e.g. for Losi 5ive-T/Mini CVD jointsy1345/03: 4 x 24 mm, e.g. for Losi DBXL and HPI Baja wheel hexy1345/04: 5 x 24 mm, e.g. for Losi 5ive-T/Mini wheel hexContents:10 pieces

Rear lower a-arms for all FG Evo cars (except 2020 series) that will bring the car to Race Truck width. The arms can also be installed as an upgrade in Sportsline trucks up to and including the 13 series. The arms are compatible with all other FG parts like uprights, Evo shock mounts and Evo stabilizer bar.Due to the increased width you will also need longer driveshafts turnbuckles for the upper a-arms and shock shafts for installation in an existing Evo. When upgrading a Sportsline truck to the Evo parts you will need a complete Evo stabilizer bar and shock mounts, rose joints and conical spacers instead. Regular price: 129.90 EURSpecial offer: 89.90 EURContents:2 pieces

Fits for FG Evolution / Competition with the new 09 short chassis.

Rear upper a-arms, a clamping system for the turnbuckles makes lock nuts obsolete.

Genuine FG spare/option part. for FG Evo 2020 to FG Evo 2020.2.Content:1 piece

Genuine FG spare/option part.The mounting of the rear damper mounts allow a higher pitch of the rear shock absorber.The model therefore has more stability in curves. Suitable for the FG Competition / EVO 04- 14 models.Contents:2 pieces