SSB020T GPM Motor pinion Super Baja Rey / 2.0 / Rock Rey, 20 teeth
Product number:
gpm_ssb020t.0
EAN:
4058575112990
Product information "SSB020T GPM Motor pinion Super Baja Rey / 2.0 / Rock Rey, 20 teeth"
Genuine GPM spare/option part.
GPM 20T steel motor pinion for Losi Super Baja Rey / Rock Rey, also suitable for other models at your own discretion. Module 1.5 mm, bore for 8 mm shaft.
We supply the pinion exclusively in a nitride hardened version. This curing has already proved extremely successful with the GPM clutch bell pinions for the Losi 5ive models and ensures significantly increased wear resistance.
Contents:
GPM 20T steel motor pinion for Losi Super Baja Rey / Rock Rey, also suitable for other models at your own discretion. Module 1.5 mm, bore for 8 mm shaft.
We supply the pinion exclusively in a nitride hardened version. This curing has already proved extremely successful with the GPM clutch bell pinions for the Losi 5ive models and ensures significantly increased wear resistance.
Contents:
- 1 piece
Login
Alternatives
Genuine GPM spare/option part. GPM 18T steel motor pinion for Losi Super Baja Rey / Rock Rey, also suitable for other models at your own discretion. Module 1.5 mm, bore for 8 mm shaft.We supply the pinion exclusively in a nitride hardened version. This curing has already proved extremely successful with the GPM clutch bell pinions for the Losi 5ive models and ensures significantly increased wear resistance.Contents:1 piece
Similar products
Genuine Top Tuning spare/option part.TopTuning 24mm hex wheel drives are required if you want to run wheel combos with the standard 24mm hex drive (such as Losi 5ive-T/B; DBXL; HPI-Baja etc.!) on your Losi Super Baja-Rey and Super Rock Rey.The stock Super Baja-Rey / Super Rock Rey20 mm hex drives (# LOS252077) will be swapped for the TopTuning 24 mm version. No additional parts are required for installation of the 24 mm hex wheel drivers. The Losi Super Baja-Rey's fake brake discs and calipers must be removed prior to assembly.Attention: For the attachment of the wheels you also need wheel nuts with M18x1.5 thread (i.e. AT-5T004), which are also offered in our shop's option menu!Please note: The adapters only fit in combination with the standard plastic steering knuckles or wheel bearing carriers. The aluminium versions have a slightly larger bearing distance, which then prevents the drive pin from being fitted.As already mentioned in the Losi instruction manual, the gearing should be adjusted depending on terrain and tire tread.Depending on tire size the rear of the fenderwells will need some cutting.This applies in particular to aggressive tread large diameter off-road tires and demanding terrain. In this case we recommend the profile regraded, nitrided 15T pinion # TT1021/07 from the TopTuning.Weight per piece 28 grams (original LOS25077 weighs 23 grams).Contents:2 pieces of 24 mm hex wheel drives, machined from 7075 aluminum2 pieces of hardened drive pins 3x23,8 mm
Genuine Top Tuning spare/option part.TopTuning 24mm hex wheel drives are required if you want to run wheel combos with the standard 24mm hex drive (such as Losi 5ive-T/B; DBXL; HPI-Baja etc.!) on your Losi Super Baja-Rey, Super Baja Rey 2.0 and Super Rock Rey. Suitable for 8 mm axles.The stock Super Baja-Rey / Super Rock Rey20 mm hex drives (# LOS252077) will be swapped for the TopTuning 24 mm version. No additional parts are required for installation of the 24 mm hex wheel drivers. The Losi Super Baja-Rey's fake brake discs and calipers must be removed prior to assembly.Attention: For the attachment of the wheels you also need wheel nuts with M18x1.5 thread (i.e. AT-5T004), which are also offered in our shop's option menu!Please note: These adapters only fit in combination with the optional aluminum spindles or wheel bearing carriers. The aluminium versions have a slightly larger bearing distance, which requires different dimensions for the wheel drives.As already mentioned in the Losi instruction manual, the gearing should be adjusted depending on terrain and tire tread.Depending on tire size the rear of the fenderwells will need some cutting.This applies in particular to aggressive tread large diameter off-road tires and demanding terrain. In this case we recommend the profile regraded, nitrided 15T pinion # TT1021/07 from the TopTuning.Weight per piece 28 grams (original LOS25077 weighs 23 grams).Contents:2 pieces of 24 mm hex wheel drives, machined from 7075 aluminum2 pieces of hardened drive pins 3x23,8 mm
%
Genuine Top Tuning spare/option part. Indispensable for optimal suspension tuning!Vacuum container for removal of bubbles from shock fluid when filling shocks.A vacuum pump is built into the lid. The tray has four holes each to accept 1/10, 1/8, 1/6 and 1/5 scale shocks.Suitable for shock absorbers from Losi, Mecatech, BWS, Arrma, Traxxas, FG, Carson, HPI and many more, as long as they have a suitable diameter. All shocks from 15 to 32 mm outer diameter can be used in the Bubble Ex to be "de-bubbled". Tray bore sizes: No. 1 = 32 mm diameter No. 2 = 21 mm diameter No. 3 = 17.5 mm diameter No. 4 = 15 mm diameter The maximum length of the shock absorber up to the upper edge of the body is about 150 mm, whereby longer shock absorbers can also be partially compressed for insertion. (e.g Losi 5ive-T and many more)Operation:Unlock the vacuum pump by turning it slightly to the left, the pump handle then extends a little. The small plug with handle is used to close and ventilate the container. To build up the vacuum, the plug must be in the down position.The small membrane on the opposite side serves as an indicator for whether a vacuum is present. Only when this is curved outwards the lid of the container can be opened again without any effort. Content: Can with integrated vacuum pump Shock tray
Genuine Top Tuning spare/option part. Motor pinion made of nitrided hardened steel, module 1.5 and 8 mm bore. Reinforced hub for set screw M5x6. The pinions with odd tooth counts are profile shifted. Within the same outer diameter, there is no need to adjust the backlash when changing the pinion. When mounting on vehicles with mounting holes in the motor mount that are specific to the tooth count, the mounting holes for the higher number of teeth in each case (16 or 18) must be used.Profile regraded:This means that the number of teeth is changed while the diameter remained constant. The part of the involute curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn´t really matter. Available in two sizes with two tooth counts:Outer diameter 30 mm with 17T or 18TOuter diameter 27 mm with 15T or 16TContents:1 piece
Genuine GPM spare/option part. GPM's aluminum rear shock tower for the Losi Super Baja Rey / Rock Rey is much more rigid than the standard plastic part. It offers an increased number mounting positions for the shock and therefore allows for a more precise setup. Contents:1 set
Hobbythek car bag for 1/6 cars.
Fits for all 1/6 models for example: FG Offroad-; Monster/Stadium-; Racetruck-; Carson-; Smartech-; Reely Carbon Fighter; Losi Super Rock Rey, Super Baja Rey, Axial Jeep and any more models.
Made from extremely durable fabric, easily washable; with wrap-around shoulder belts and zipper closure.
No dirt in the car boot!
Dimensions:
Length: 70 cmWidth: 50 cmHeight: 40 cm
Genuine GPM spare/option part. Rear wheel bearing carriers for Losi Super Baja Rey / Rock Rey, 0° toe-in (stock) made by GPM, machined from high grade 6061-T6 aluminum provide better fit for the bearings and therefore increase their life span.We recommend installing the ball bearings with a little dab of screw cement.Contents:2 pieces
Genuine rc-car-online spare/option part. Komplete set of screws, nuts and washers for the Losi Super Baja Rey.The set includes a total of 321 screws, in different quantities which are all used on the Losi Super Baja Rey / Rock Rey.6 sizes of cap head screws11 sizes of CSH screws13 sizes of button head screws6 sizes of set screws3 sizes of washers4 sizes of self-locking nutsComes in a high quality 190x170x40 mm assortment box.Contents:Cap head screws in 12.9:4 piecesM2x101 piecesM2,5x813 piecesM3x102 piecesM3x122 piecesM3x165 piecesM3x306 piecesM3x45 CSH screws in 10.9:5 piecesM2,5x86 piecesM3x66 piecesM3x1234 piecesM3x161 piecesM4x1010 piecesM4x122 piecesM4x149 piecesM4x166 piecesM4x1814 piecesM4x202 piecesM4x25Button head screws in 10.98 piecesM3x89 piecesM3x195 piecesM3x126 piecesM3x1616 piecesM3x204 piecesM3x304 piecesM3x3512 piecesM4x128 piecesM4x1618 piecesM4x2010 piecesM4x2512 piecesM4x301 piecesM4x35Grub screws:2 piecesM3x63 piecesM4x46 piecesM4x56 piecesM4x61 piecesM5x48 piecesM5x30Washers:Unterlagscheiben:5 piecesM3,25 piecesM4,34 pieces H5 Seeger HalfmoonSelf-locking nuts:4 piecesM335 piecesM4Nuts:2 piecesM45 piecesM5
Genuine rc-car-online spare/option part. Complete set of sealed (2RS) bearings for Losi Super Baja Rey / Rock Rey.4 pieces 4 x 8 x 3 mm Losi # LOS25700715 pieces 8 x 16 x 5 mm Losi # LOSA6942/016 pieces 10 x 19 x 5 mm Losi # LOS257006Price bought separately 78.56 EURSpecial-offer price for the complete set 39.90 EURContents:25 pieces of of sealed (2RS) bearings
The GPM stainless steel trailing arm and steering linkage set for Losi Super Baja Rey contains a billet aluminum servo arm, the link rod from servo to servo saver, the steering rods and the upper trailing arms. Turnbuckle style rods made of stainless steel are used. This allows to change the length of these rods easily without disassembly and the suspension setup can be changed.
Genuine GPM spare/option part. Upper GPM aluminum a-arms for Losi Super Baja Rey with replaceable ball joints and plastic bushings. The higher stiffness of the aluminum parts increases steering precision and suspension response. Contents:4 pieces / 2 pairs
Genuine GPM spare/option part. Reinforced rear drive shaft from GPM, suitable for Losi Super Baja Rey / Rock Rey for connection of center diff and rear axle, hardened all-steel version. Much stronger than the standard version with plastic center section. Replacement for LOS252072. Contents:1 piece
Customers also viewed
Genuine Top Tuning spare/option part. Motor pinion made of nitrided hardened steel, module 1.5 and 8 mm bore. Reinforced hub for set screw M5x6. The pinions with odd tooth counts are profile shifted. Within the same outer diameter, there is no need to adjust the backlash when changing the pinion. When mounting on vehicles with mounting holes in the motor mount that are specific to the tooth count, the mounting holes for the higher number of teeth in each case (16 or 18) must be used.Profile regraded:This means that the number of teeth is changed while the diameter remained constant. The part of the involute curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn´t really matter. Available in two sizes with two tooth counts:Outer diameter 30 mm with 17T or 18TOuter diameter 27 mm with 15T or 16TContents:1 piece
Genuine UFRC spare/option part. Fits Ghost Rabbit GR1.Contents:1 pieces