SPM6742 TM1500 DSMR Telemetry Module

€54.99*

Available

Product number: SPM6742

Product information "SPM6742 TM1500 DSMR Telemetry Module"

The Spektrum™ TM1500 DSMR Telemetry Module allows drivers to add telemetry feedback to their telemetry compatible DSMR Spektrum transmitters when receivers absent of integrated telemetry, Such as the SRS6000 and SR410 Receivers, are installed. The TM1500 is a small light weight module that only requires a single connection to the receiver. This unit features an easy to use bind button and ports for voltage, temperature, RPM, and X-Bus expansion sensors.

Produkt Eigenschaften

Product Height	0.7 in (16.9 mm)
Product Length	1.5 in (37.6 mm)
Product Width	1.1 in (27.4 mm)

1 piece

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Similar products

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters

Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€37.90*

y0735 Safety clip for Universal / JR / Futaba connectors

Genuine HT spare/option part. Protects the mated connection to prevent them from coming apart accidentally. Particularly recommended for direct power supply cords, as a tensile load on the cable can remove the link unnoticed and then you would perhaps think of a servo failure in the first place.The small size usually allows the installation even inside the receiver box.Also suitable for securing the connection of the receiver battery; the use of this clip means a big improvement in safety with little effort.Contents:1 piece

€1.50*

DYNE1240 Dynamite Large Scale Safety Kill Switch

Genuine Dynamite spare/option part.Key Features:Kills your 2-cycle gas engine on command, loss of radio signal, low battery, or total battery power lossComes ready to install no soldering requiredOptically Coupled to isolate your ignition system from your radio systemBuilt-in LED for easy-to-spot operational status3-Channel Radio System RequiredNot Compatible with AVC-Equipped ReceiversContents:1 piece

€39.99*

Details

TT0990/02 Top Tuning Futaba 2-pin male connector with cable for Failsafe

Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.2-pole connection cable with silicone insulation and 22 AWG/0.32 mm² cross-section, length approx. 80 mm.Contents:1 piece

€3.90*

HSF0000655 DYMOND 5-in-1 Smart Battery Meter (battery and servo tester)

Genuine Dymond spare/option part. Contents:1 piece

€19.90*

Low voltage failsafe module, y0423 - 1pce.

To protect a car from a crash in case the power supply fails is no easy task. The mechanical devices that are used to do the job are either bulky or cause a higher drain from the battery. The failsafe module is a more efficient way.The module controls the battery pack's voltage and takes control of the throttle servo when the voltage goes below 4.7 volts. As an additional feature you can supply a backup battery pack to power the throttle servo in case the main pack falls completely. The failsafe position of the throttle servo is adjustable.

€49.30*

54004 SMD-Failsafe module

Failsafe unit with adjustable servo position, very low current drain (0.05mA). Excellent value for money!The circuit responds to failure of the control signals. When transmitter and receiver work correctly, the received control pulses determine deflection of the servos; but as soon as control pulses are missing, the circuit lets the connected servo run to a pre-set safety position. Thereby, loss of the model can be avoided.Attention: not compatible with digital servos!

€28.70*

y1569 Low voltage buzzer with voltage test

Genuine HTspare/option part. The LiPo Voltage Checker provides a low voltage alarm for 28S cell counts.When the voltage is below the set value, an alarm will sound along with illuminating the red LED.The voltage checker will automatically detect the cell count when connected to the balance lead on 28S LiPo. SpecificationsInput: 1S (JST) and 28S (JST-XH) LiPo, Li-ION/LiMN/Li-FeUnit Voltage Display Range: 0.54.5 VTotal Voltage Display Range: 0.536 VTest Mode Voltage Range: 3.730 VAlarm Value Range: 2.73.8 V, including offDimensions: 3.9 cm x 2.4 cm x 0.9 cmContents:1 piece

€9.90*

TT0990/03 Top Tuning JR/universal 3-pin female connector with cable for Failsafe

Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.3-pole connection cable with PVC insulation and 24 AWG/0.2 mm² cross-section, length approx. 220 mm.Contents:1 piece

€3.90*

TT0990/04 Top Tuning Plug-in mount for 5 mm LED for Failsafe

Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.Plug-in mount for front panel installation, requires 8 mm diameter mounting hole.Contents:1 piece

€3.90*

battery monitor, y19004

The battery monitor allows to check battery voltage and servo load. Different connectors available, your choice of 6 or 7,2 volts version.

€37.90*

y0416 Hobbythek failsafe module

Genuine HT spare/option part.Failsafe unit with adjustable servo position, very low current drain (0.05mA). Excellent value for money!Attention: not compatible with digital servos!Contents:1 piece

€29.90*