RC - Paint Lexan in 33 different colors spraycan (Offer) Buy 3 get 4

Fits most spray cans from many manufacturers.Convert your spray can into a spray gun. The long-lever system of this handle makes using a spray can much more convenient and provides better flow rate control as well.No more dirty hands from paint work.Contents:1 piece

Genuine HT spare/option part.RC - Paint is a special paint for lacquering RC-Car Lexan (Polycarbonate) body shells. The ultra-fine mist provides optimal coverage! Through an optimized atomizer valve an outstanding painting result is guaranteed. The content of the can is 150ml and suffices - depending on the intensity of the painting, - for one 1/8 or two 1/10 body shells. Two to three cans are needed for a 1/5 or 1/6 body shell.RC-Paint Lexan color is produced in a particularly environmentally friendly. The composition of colors (color pigments) was placed on the lowest possible heavy metal content and the best possible environmental compatibility of the solvent and propellent gas value.Contents:1 piece / 150 mlPainting tips:

Genuine HT spare/option part.RC - Paint is a special paint for lacquering RC-Car Lexan (Polycarbonate) body shells. The ultra-fine mist provides optimal coverage! Through an optimized atomizer valve an outstanding painting result is guaranteed. The content of the can is 150ml and suffices - depending on the intensity of the painting, - for one 1/8 or two 1/10 body shells. Two to three cans are needed for a 1/5 or 1/6 body shell.RC-Paint Lexan color is produced in a particularly environmentally friendly. The composition of colors (color pigments) was placed on the lowest possible heavy metal content and the best possible environmental compatibility of the solvent and propellent gas value.Contents:1 piece / 150 mlPainting tips:

TAMIYA PS = Polycarbonate spray paints are specially developed for painting unpainted kit body shells. Numerous colour shades are available and allow the individual design of models. Each can contains 100 ml of highly opaque paint, which is oil and fuel resistant, allowing the use on nitro models.The body shell should be degreased and cleaned before use. Best painting results are achieved when thin layers of paint are sprayed on from a distance of approx. 30 cm. Between two spraying processes the paint should dry slightly to avoid "tears".Always follow the painting instructions of models and on the can. Danger warnings: H222 Extremely flammable aerosol. H229 Container is under pressure: may burst when heated. H315 Causes skin irritation. H318 Causes severe eye damage. H335 May cause respiratory irritation. H336 May cause drowsiness and dizziness. EUH066 Repeated exposure may cause skin dryness or cracking. Content: 100 ml spray can with spray headPainting tips:

This model is fitted with numerous aluminium parts: front and rear side bulkheads, rockers, engine mount, suspension arm ends...Steel made Uniball sockets all possible enable all adjustments of the front and rear suspensions.The transmission made with a gearwheell drive offers outstanding reliability and smooth operation.Just like all other FG Competition models the FG Formula 1 Competition is the most successful model of the past years. The experiences we gained from numerous competitions have all influenced this version. The FG gearwheel drive which is extremely smooth running and cares for more power reserves. Surely FG Modellsport has created a competitive model for the next years with this version which will seamlessly follow up on the past successes. Highlights Alloy wishbones FG gearwheel drive Alloy rear axle plate FG alloy shock absorbers 04 Ball-bearing alloy servo saver 26 ccm Zenoah-Engine Airbox Tuned pipe Front- and rear brake 5 mm Chassis Lexan body shell Technical description of the FG Formula 1 Competition ki:The undercarriage of the FG Formula 1 Competition is built on an 5mm alloy chassis. All screws at the bottom of the chassis are countersunk.Front and rear axle mounts as well as the engine unit are connected over the complete length of the chassis, therefore we achieved almost the stiffness of a monocoque chassis. The quick fix system of the engine makes a fast changing of the engine possible. The drive to the rear axle is carried out over several easy-running front gearwheels and an FG ball drive at the rear axle. A separate flange bearing holds the clutch bell in order to relieve the crankshaft. Front and rear axle with their various adjusting possibilities as king pin angle, castor a.s.o. consist of alloy delta wishbones below. Solid alloy rear axle plates reduce the wear at the rear axle and give an enormous driving stability. 4 oil-pressure shock absorbers controlled by a pushrod suspension as well as stabilizers guarantee an optimal ground contact.We deliver the chassis selectively with tuning bowden cable brakes for front or respectively rear axle. The model is powered by a high-capacity 26 cm³ engine with airbox and Tuning pipe.Equipment of the FG Formula 1 Competition kitCNC-cut 5mm alloy chassis with lateral carbon fiber inserts, 26 cm³ engine, inlet silencer, Tuning pipe, FG gearwheel drive, ball drive, complete rear and front axle carrier unit with integrated engine quick-fixing device, double alloy wishbone fastenings, lower alloy delta wishbones at front and rear axle, front and rear alloy uprights, ball-bearing servo saver, steering stops, pushrods, 4 oil-pressure shock absorbers with alloy damper pistons, mechanical Tuning brakes at front and rear, stabilizer for front and rear axle, 10mm alloy balls, rear spoiler, polycarbonate body shell, polyamide front spoiler, receiver box, competition tires with tire inserts.We deliver the models as a kit including mounting instruction. The body parts are made of clear polycarbonate for your own painting. FG stickers and writings are enclosed.For the final assembly of the models you need further: radio control system (transmitter, receiver), 1 large steering servos (each approx. 40 - 50 kg), 2 servo for throttle brake (approx. 20 - 30 kg), batteries and charger.These parts are not included and must be supplied or ordered separately when the rc installation option is selected! Includet Zenoah 26cc engine Clear bodyshell and polycarbonate spoiler Mechanical brakesDimensions Length: 960mm Width: 440mm Height: 230mm Wheelbase: 620mm Formular 1 models in action!

FG body kit Alfa Romeo 156 WTCC made of 1 mm Lexan, painted. The body kit consists of the main body, front body and rear spoiler and is is red/black, as shown in the photos.  The rear spoiler is painted black. The window frames have been painted black and the windows are slightly tinted. There are no holes drilled in the body and can therefore be fitted to any on-road RC car with a 530 mm wheelbase.  Body mounts required: Front part: FG 7020/10 Front bumper Rear carrier: FG 7152/01 Rear body supportFront side: FG 8013 Body support Rear side: FG 7014 Body support Dimensions: Length: 900 mm Width: 400 mm Height: 245 mm Wheelbase: 530 mm  Contents 1 piece

Parma Faskolor is a non-toxic water based lexan color, specially formulated for airbrush application. Nevertheless it is also possible to paint small parts with a normal brush.The color is very resistant to cracking, chipping and peeling. The color comes in 60 ml bottles.

Genuine Mecatech spare/option part for the FW01.Content:1 piece