Losi 5ive-T Race body with cage, used

1 set Hemistorm Penta body kit, 5-piece.  The body fits on the Losi 5ive-T cage. See photos for condition and scope of delivery.

If you want a special combination of compounds please enter that information into the "note to us" form field at the end of the checkout process.Mammoth Supergrip for 1/6 and 1/5 offroad cars. Fits too for Formular 1 models!Parking lot / race tires for your offroad car.VersionWidthOuter diameterFront64 mm153 mmRear78 mm153 mmGlued on genuine FG rims (rear tires using extension rings), with foam rubber inserts included. Rim has 18 mm square drive with reinforcement ring.Please note: based on experience we recommend against using other manufacturers rims and extensions. Since the Mammoth tires provide very good grip the rim and the bonding must withstand high loads. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.The Mammoth Supergrip is available in in the following compounds: Super softSoftMediumHardFront tirey0581y0582y0583y0584Rear tirey0591y0592y0593y0594General recommendation:The dirtier the track or the lower the ambient temperatures, the stickier (softer) the rear tires should be.Hint regarding the front tires: 2WD cars should use them one or two grades harder then the rears. 4WD cars usually like the same compound all around.Of course, the softer the tire the higher the wear rate; and this applies to Mammoth Supergrip onroad tires as well.The tires have a special onroad thread pattern but will still provide ideal traction after the pattern has been worn out. The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall.Prices per unit: FrontRearMammoth Supergrip:Pair44,90 EUR49,90 EURTire inserts:Pair13,00 EUR13,00 EURFG rim:Pair14,90 EUR14,90 EURFG extension ring:Pair--.-- EUR14,90 EURMounting:Pair13,00 EUR13,00 EURTotal Price                                                                                            85,80 EUR    105,70 EUR = 191,50 EUR SETTotal for 1 pair each front and rear: 169,90 EUR================================Also suitable for:With the following wheel adapter: y1183 Rim adapter

This genuine factory painted Losi 5ive-T body shell set with decals .New version of the 5ive-T body shell with scoop on the hood for optimized cooling!The set includes the following genuine parts (unit parts only clear available!): LOS350005 Front sectionLOSB8102 Center sectionLOSB8103 l/h rear fender with plateLOSB8104 r/h rear fender with plateLOS259003 Vehicle decalwith factory paint job on all body parts and decals applied. Delivery without roll cage!

With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.With the new "K & N" version of the Losi DBXL there is another detail, which need to be considered.From the very beginning the hole pattern for the engine installation in the DBXL chassis plate was no precise match to the hole pattern of the engine, even when delivered in stock form with standard engine. Now with the "K&N" version the engine mount has been changed to eliminate this discrepancy. However, all aluminum engine mounts available on the market share their dimensions with the previous plastic engine mount. For the installation of a G320 Zenoah in a "K&N" -DBXL two possible combinations exist in order to obtain the correct hole pattern:When using the standard (new) plastic engine mount a shortened clutch housing is required as in a 5ive-TWhen using an aluminum engine mount a stock length clutch housing is requiredSeparately, it is recommended to enlarge the cutout in the body panel in front of the K & N air filter for about 2 - 3 mm to ensure that the panel cannot chafe on the air filter.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

Genuine Losi spare/option part.Contents:1 set

BUILD YOUR OWN ORIGINAL,AUTHENTIC HPI BAJA 5BHPI large scale fans, we have heard you! The one and only original HPI Baja 5B is BACK and ready for you to build from the ground up! The HPI SBK collection of Self Build Kits grows with the addition of not just one, but TWO 1/5th scale HPI kits! Fans of large scale off-road RC will be super excited to build their own gas-powered 1/5th scale Buggy with the HPI Baja 5B Self Build Kit!When the HPI Baja 5B buggy was first introduced, large scale RC was very expensive and quite difficult for the average RC hobbyist to experience. Using highly durable parts and innovative design features, HPI brought large scale off-road to new enthusiasts and ushered in a new, BIGGER era of RC!Now, YOU can build and own the legend! Experience the thrill and excitement of building a car which ends up being over 80cm (nearly 32 inches) long and weighing nearly 10kg (over 21 lb)! Just install your own engine and electronics as you build the HPI Baja 5B and you'll be ready for any adventure that comes your way!With extra-tough drivetrain parts like the viscous torque differential, super-durable composite spur gear with internal damping and all-metal drivetrain, the HPI Baja 5B is ready for your 23-32cc 2-stroke engine so you can experience the joy of gas-powered RC and up to 30-minute runtimes!The HPI Baja 5B is also equipped with extra-big and super-tough suspension parts, featuring awesome HPI durability! With its expertly designed molded composite suspension plus extra-long adjustable HD shocks, and massive high impact nylon 3-piece beadlock wheels, the Baja 5B is ready for full-speed racing on any off-road circuit!The 4mm thick 6061 aluminum monocoque chassis gives the HPI Baja 5B the classic desert racing buggy look. Precisely bent into shape for maximum strength, the chassis provides the mounting points for the engine and suspension, forming the backbone of the car. Precise steering is provided by a dual-bellcrank rack and cam-type servo saver. Aluminum parts are anodized in cool gunmetal and the classic Baja desert racer clear polycarbonate body is included in the SBK kit, ready for your custom racing scheme!The Baja 5B SBK is a great addition to your HPI collection, as well as a fabulous introduction to large scale buggies!RACING CHASSIS DESIGN & LAYOUTThe narrow channel chassis made from rigid 4mm 6061 aircraft aluminum and gives the HPI Baja 5B a classic desert racing buggy look and extreme stiffness and durability. The U-shaped chassis is protected at the rear with a thick plastic skid plate for extra protection to the motor and drivetrain.The tube roll cage is made of high impact nylon and topped with a real aluminum roof to carry on the classic looks. The roll cage is fully functional and protects the motor and internals from crash damage. The roll cage, radio box, body panels, wing, undertray and gear case are all mounted with fast access clips for easy maintenance. To finish you need: Engine with clutch and exhaust Remote control with servos and receiver battery Charger Two cans of Lexan paint Features Summary Unassembled 1/5th scale Off-Road Buggy Ready for your 23-32cc RC engine Ready for your electronics Enclosed radio box Baja desert racing body design Adjustable HD shock absorbers Monocoque chassis Low CG for superior handling Long travel suspension Viscous torque oil-filled gear differential All-terrain tires Beadlock wheels with metal insert hubs Aluminum rear shock tower Hard plastic skid plates Adjustable rear wing Quick access to all critical maintenance points Dual bellcrank steering Cam type servo saver Race spec Hex socket hardware Gunmetal anodizing Full set of rubber-sealed ball bearings Chassis Specifications Overall Length 817mm Height: 255mm Width: Front - 460mm; Rear - 480mm Tire Track (to center of tires): Front - 395mm; Rear - 400mm Wheelbase: 570mm Ride Height: 76mm Suspension Travel: Front - 95mm; Rear - 100mm Weight: 9.6kg (21.3lb) Adjustable Camber: front - shims; rear - screw Front caster: adjustable with shim 22 / 25.5* / 29 degrees (* stock) Toe-in: Front adjustable with tie rod; Rear adjustable with inserts 0-4 degrees (3 degrees stock set-up) Aircraft aluminum 6061 T6 monocoque chassis Double wishbone suspension with adjustable roll center F/R Drive system: HD metal gears with sealed gear box (8.382:1 gear ratio) Differential: viscous torque control with 4 pinion gears; sealed diff case with silicone oil Shock absorber: HD Aluminum coilover shock absorber with fully adjustable preload collar Wheel type: 3-piece beadlock design, high impact nylon material with inset heavy-duty metal hex hub