LOS252127 Losi Diff Shims, 24x21x0.3mm, DBXL-E 2.0

€9.99*

Prices incl. VAT plus shipping costs

Available

Product number: losi_los252127

EAN: 605482496169

Product information "LOS252127 Losi Diff Shims, 24x21x0.3mm, DBXL-E 2.0"

Genuine Losi spare/option part.

Contents:

10 pieces

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Customers also bought

y0809 Klüber high performance grease for differentials

Freaking expensive, but it is damned fine.ASONIC HQ 72-102 is a synthetic high-temperature lubricating grease, for use in limited slip differentials. Due to the careful selection of product components and the clean manufacturing environment, ASONIC HQ 72-102 is a rolling bearing grease with a particularly low noise level.Benefits for your application:High-temperature lubricating grease for rolling bearingsHigh purityLow noiseGood water resistanceContent:1 piece, tube with 30g

Content: 30 Gramm (€730.00* / 1000 Gramm)

€21.90*

y0744 Differential Silicone oil / grease, viscosity 15.000 untill 2.000.000, 50 ml

y0744 Viscosity: y0744/07 - 1.000.000+ 4.9EUR

For changing the locking effect of large scale car differentials.Top quality in 50 ml plastic wide-neck bottles.Silicone oil / grease with a viscosity to choose:15.00030.00050.000100.000300.0001.000.0002.000.000Viscosity of silicone oil at various temperatures.

Content: 50 Milliliter (€356.00* / 1000 Milliliter)

Variants from €12.90*

€17.80* €19.80* (10.1% saved)

DBXL023/3 ATOP Aluminum/steel differential case for DBXL/XL-E/XL-E 2.0, set of 3

Genuine ATOP spare/option part. Set of 3!Two-part differential housing made of aluminum with steel bearing shield. The one-piece steel end shield ensures greater stability compared to aluminum end shields with a pressed-in bushing.Fits all differentials in all DBXL and DBXL-E 2.0 versions!The delivery includes gaskets and O-rings, screws, ball bearing and sliding blocks.Contents:3 pieces

€149.90*

AT-DBXL002 ATOP aluminum camber rods/steering rods for Losi DBXL/DBXL-E

Genuine ATOP spare/option part. Camber rods for Losi DBXL with center section cnc-machined from 6061 aluminum by ATOP. High grade all-metal ball joints at the pivot points provide zero backlash and strength. Fits front and rear.Attention: On a DBXL-E 2.0 these rods can only be used as camber rods, not as steering rods! Dimensions: Hole to hole: 117mm Total length: 135mm Contents:2 pieces

€34.90*

LOS250055 Losi Wing, FOX Racing, DBXL-E 2.0

Genuine Losi spare/option part. Contents:1 piece

€29.99*

Details

Similar products

LOS254006/01 Suspension Arm Losi DBXL 1/5 4WD

Genuine Losi spare/option part. Content:1 piece

€16.90*

LOS252120 Losi Axle Boot Set 5mm Drive Pins DBXL-E 2.0

Genuine Losi spare/option part. Contents:10 pieces

€29.99*

LOS252020 Universal Rebuild Kit (2): 1:5 4wd DBXL+MTXL

Genuine Losi spare/option part.Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!Contents:1 set

€11.99*