LO5T056-ACC Spare bushings set for GPM/Losi 5ive-T rear a-arms LO5T056, set

€8.90*

Prices incl. VAT plus shipping costs

Available

Product number: gpm_lo5t056_acc

EAN: 4058575040156

Product information "LO5T056-ACC Spare bushings set for GPM/Losi 5ive-T rear a-arms LO5T056, set"

Bushings set for GPM rear a-arms part no. LO5T055.

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

No reviews found. Share your insights with others.

Customers also bought

LO5T055-ACC Spare bushings set for GPM/Losi 5ive-T front a-arms LO5T055, set

Bushings set for GPM front a-arms part no. LO5T055.

€17.99*

BJ056/DC Delrin bushings, spare part for GPM rear löwer a-arm

Delrin bushings, spare part for GPM rear lower a-arms BJ056 for HPI Baja cars, set of eight.Dimensions:Outer diameterer: approx. 8.1 mmInner diameter: approx. 6 mmLength: approx. 9.7 mm

€4.90*

AT-5T023/024 ATOP Aluminum a-arms front and rear Losi 5ive-T/2.0

Genuine ATOP spare/option part.Light weight design (Total weight of all the wishbones is a mere 444 grams), CNC-machined from 6061-T6 aluminum by ATOP a-arms fits Losi 5ive-T front. The chassis-side is wider than stock arms to bring the large longitudinal play at this point down to a reasonable level.Plastic bushings for the hinge pins guarantee low wear. On the wheel side floating stainless steel bushings allow for normal tightening of the c-hub screws.Contents:1 set

€149.90*

LOSB3225 Losi F/R Wheel Hex & Pin 5T, TLR 5ive-B and Mini

Genuine Losi spare/option part.Fits Losi 5ive-T, TLR 5ive-B and 5ive Mini.Dimensionally identical with B55015Content:2 pieces

€39.99*

TLR354001 TLR hinge pin, rear outer, TiCN coated, 5ive-T/2.0, TLR 5ive-B and Mini WRC

TLR hinge pin for Losi 5ive-T, TLR 5ive-B and Mini WRC, rear outer; TiCN (titanium carbon nitride) coated; approx 79.5 mm long.Direct replacement for stock hinge pin from the set LOSB 2080.Contents:2 pieces

€19.99*

Customers also viewed

LOSB3218 Losi Front Center Driveshaft & CV Coupler 5T and Mini

Genuine Losi spare/option part.Fits Losi 5ive-T and 5ive Mini.Content:1 set

€19.99*

%

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters

Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€34.90* €42.90* (18.65% saved)

AT-5T023/024 ATOP Aluminum a-arms front and rear Losi 5ive-T/2.0

Genuine ATOP spare/option part.Light weight design (Total weight of all the wishbones is a mere 444 grams), CNC-machined from 6061-T6 aluminum by ATOP a-arms fits Losi 5ive-T front. The chassis-side is wider than stock arms to bring the large longitudinal play at this point down to a reasonable level.Plastic bushings for the hinge pins guarantee low wear. On the wheel side floating stainless steel bushings allow for normal tightening of the c-hub screws.Contents:1 set

€149.90*