The Ezrun Max4 controller is suitable for particularly large 1:4 and 1:5 scale models. This controller is ideal for use in any of these models, whether heavy-duty off-roaders or trucks. It is the ideal choice for high-end models that are subject to high demands or are operated aggressively. Despite the enormous size, care was taken to use high-quality and, above all, durable materials in the construction. This can be seen, for example, in the fact that the Max4 controller is excellently protected against dust, water and similar external influences. The electronic switch is also optimally protected against damage that could otherwise occur during a normal ride. In addition, the Ezrun Max4 has a built-in super high-current BEC that can provide a maximum output power of up to 25A. The output voltage can therefore be switched between 6V, 7.4V and 8.4V. The high-current BEC was developed to supply the latest high-current servos with sufficient power on request and thus to be able to precisely control the appropriate large models. Features - Super-strong switch mode BEC with a constant current of 10A, instant 25A and the ability to switch between 6, 7.4 and 8.4V - Fireproof circuits to protect the battery connector - Additional built-in protection mechanisms: undervoltage, overheating, signal loss, ... - Versatile programmability - Real-time data recording Technical data: Current (continuous/short) 300A / 2000A
Motor type: Sensor/sensorless brushless motors
Motor limit: 12S LiPo: kV <= 600 (70125 size)
LiPo cells: 6-12S
BEC: 6V / 7.4V / 8.4V with 10A (switchable)
Fan: Yes (supply via built-in BEC)
Programming input: Fan / PRG input
Programming: LED programming card, LCD programming box, OTA programming module
Size: 125x85x61.7mm
Weight: 775.4g
Application: 1/4 and 1/5 Heavy Duty-Off-Road, Trucks
Product information "Hobbywing OTA Bluetooth Programer"Thanks to the OTA Programming Module, Hobbywing ESCs can be programmed in a new modern and intuitive way. The ESC is wirelessly connected to a smartphone via the Bluetooth signal sent by the module. All parameters can then be selected and set as usual in the Hobbywing "HW Link" app.The OTA programming module is also smaller and lighter than a conventional programming box and therefore fits comfortably in any pocket. So perfect for on the go.FeaturesEasy to operateCompact designData Recording in real time (compatible ESC required)Firmware-Update within the "HW Link"-AppInclusive Reset-Button on the bottom sideSuitable for the following HobbyWing productsselected XERUN and EZRUN-ESCs for RC carsselected PLATINUM-ESCs for RC aircraftsselected SEAKING-ESCs for RC BoatsTechnical SpecificationsDimensions:30x25.5x8.5mmWeight:10.2gWorking Voltage:5-12.6VEffective Range:0-3mSupported Bluetooth-Version:>/= 4.0 Notice: You can download the "HW Link"-App by Hobbywing for Android-Devices in the Google Play Store as well as for IOS-Devices in the Apple Store.
Product information "HW30402850 Hobbywing Ezrun 70125SD 560kV 4pol, 8mm Shaft for 1:5"
Product information "Hobbywing Ezrun 70125SD 560kV 4pol, 8mm Shaft for 1:5"
Hobbywing's Ezrun 70125SD motor is a powerful complement to the MAX4 ESC, providing heavy-duty off-roaders and trucks in particular with just the power needed for action-packed rides.
Features
Perfect sensor mode in combination with the Ezrun MAX4 ESC
CNC-milled aluminum housing, 0.2mm silicon steel sheets and other high-quality building materials
Four sintered NdFeB magnets for super torque, stable performance and explosive power
Innovative new sensor interface
Waterproof and dustproof thanks to the rubber cover of the bearing
Independent, high-precision encoder in the motor to communicate the rotor position without any interference
More power and less heat development with the same load
Technical Specifications
Sensor Type:
Sensored
Poles:
4
kV Rating:
560kV
LiPo Cells:
8-12S
No-Load Current:
3.6A
Outer Diameter:
70mm
Length:
125mm
Shaft Diameter:
8mm
Shaft Length:
30mm
Weight:
1995g
Application:
1/5 Heavy Duty Off-Road, Truck
Related links to "Hobbywing Ezrun 70125SD 560kV 4pol, 8mm Shaft for 1:5"
0 of 0 reviews
Average rating of 0 out of 5 stars
Leave a review!
Share your experiences with other customers.
Login
No reviews found. Share your insights with others.
Genuine Top Tuning spare/option part. Specifications Max. amps: 129 A Max. voltage: 57 V Max. power: 7,350 W KV (RPM/Volt): 520 KV Mounting hole depth: 8 mm Bolt pattern: 4 x M4 at 30 mm pitch circle diameter Case diameter: 57.8 mm Case length: 112 mm Free shaft length: 30 mm Shaft diameter: 8 mm Weight: 1260 g Connector: 6.5 mm diameter Cable size: 8AWG Features High quality bearings 4Pole rotor with high quality magnets Stator - super thin silicon steel layers Super strength 8 mm shaft CNC Aluminium heatsink case Copper wires with high temperature endurance Contents:1 piece
Product information "Hobbywing Ezrun SL 56118SD G2 650kV 4pol, 8mm Shaft for 1:5"The Ezrun 56118SD G2 motor offers convincing performance for 1/5 buggies and trucks. Powerful and made of high quality materials, this engine promises long-lasting fun and a long time. The innovative new sensor interface and rubber cover bearing also provide better waterproof and dustproof effect than traditional and comparable sensor motors.FeaturesNew waterproof sensor cableCompletely sensor-controlled system for more acceleration and greater power development.Best used with the Hobbywing Ezrun MAX5 HV G2 ESCWith high-precision encoder to detect rotor position to counteract interference and enable stable running in sensor mode.Use of high-quality components such as CNC-machined aluminum housing, high-purity copper windings, high-strength explosion-proof rotor, etc. for high durability and smooth running.Easily dismantled for maintenance workTechnical SpecificationsType:Brushless, SensoredkV Rating:650kVNo-Load Current:5.5ACells LiPo:8-12SPoles:4Diameter:56mmLength:119.2mmShaft Diameter:8mmShaft Length:30mmWeight:1272gApplication:1/5 Buggy, TruckDelivery1x Motor1x Manual
Genuine Top Tuning spare/option part. Specifications Max. amps: 175 A Max. voltage: 42 V Max. power: 7,350 W KV (RPM/Volt): 700 KV Mounting hole depth: 8 mm Bolt pattern: 4 x M4 at 30 mm pitch circle diameter Case diameter: 57.8 mm Case length: 112 mm Free shaft length: 30 mm Shaft diameter: 8 mm Weight: 1260 g Connector: 6.5 mm diameter Cable size: 8AWG Features High quality bearings 4Pole rotor with high quality magnets Stator - super thin silicon steel layers Super strength 8 mm shaft CNC Aluminium heatsink case Copper wires with high temperature endurance Contents:1 piece
The EzRun MAX6 G2 is a modern brushless controller with high-voltage support and an integrated Bluetooth module. Compared to its predecessor model, the second generation is considerably more powerful with up to 200A and, with 12 programmable parameters, also offers more scope for customisation to suit your personal driving style. Aggressive starts, high acceleration on straight stretches and jump control are just a fraction of what the controller has to offer. And thanks to the intelligent freewheel technology, the controller remains relaxed and cool even during these demanding manoeuvres.
Probably the most convincing feature of the MAX6 G2 controller is the integrated Bluetooth module. This eliminates the need for programming cards and the OTA module as additional accessories. All you need now is the HWLink2 app and the controller can be conveniently programmed and updated on your smartphone. It is even possible to record data for up to 10 minutes and provides an insight into the most important driving data such as speed, voltage and temperature. With a powerful integrated BEC, an anti-spark design and several protective devices, this speed controller offers advanced functions and a high level of safety. The EzRun MAX6 G2 is therefore the ideal choice for RC enthusiasts looking for maximum potential and the best reliability. With perfect compatibility with both Hobbywing's EzRun 4990 G2 and 5690 G2 motors, this power system offers an unbeatable team for optimum performance with modern features.
Features - Now with even more power than its predecessor. - Integrated Bluetooth module to programme the controller directly via the HWLink2 app on your smartphone. - Intelligent fan that only activates when the temperature reaches a certain value.
Water & dust resistant to IP67 standard for use in all weather conditions. - Built-in ultra-strong switching mode BEC to address a wide range of servos (high power / high voltage servo). - Turbo timing setting included. - Especially recommended with the matching motor (e.g. EZRUN 4990 G2 or 5690 G2). - Several protective functions: Battery undervoltage protection, controller and motor overheating protection, signal loss protection, current protection. - Built-in data logging function to display various running data of up to 10min in the HW LINK app - Supports firmware upgrade of the controller. - 12 adjustable parameters.Technical Data Type: 1/6 Brushless Sensored Current (continuous/short): 200A / 1200A Input voltage: 3-8S LiPo BEC: 6V/7.4V/8.4V @8A (switch mode) Motor types: Brushless motors (with/without sensor) Motor limits: - 6S Lipo: KV <= 2400
- 8S Lipo: KV <= 1700 4990/5690 motor
Fan: Yes, operated via the BEC Programming: HWLink2 app (via the integrated Bluetooth module) Waterproof: Yes Size: 70x56x45.5mm Weight: 245g Applications: 1/6, 1/7 on-road, truck, monster truck Scope of delivery: Ezrun MAX6 HV G2 ESC
The 2WD-465 Sportsline model is built on the short chassis with double a-arms suspension front and rear. The vehicle is equippedwith the 2-shocks front suspension as standard, which ensures optimum traction for both front wheels.On the GT2, the front axle has been widened to 384 mm. The rear axle is 395 mm wide.Technical description:The model has a 465 wheelbase. The models are built on a 4mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in. Further equipment points are front disk brakes, differential gear, easy-running FG ball drive, alloy brake calliper with big brake disk, stabilizer bar front and rear, tuned pipe muffler, rear brace, 24T steel pinion, spark plug cap suppression cover, latest version (Evo) oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The models are equipped with a powerful 23ccm combustion engine. The engine needs a 2-stroke petrol oil mixture. One tank filling gives you about 45 minutes driving fun. The power is transmitted over the well-tried system: from the engine over the 2-block clutch over radial tooth wheels on to the rear axle which is equipped with the bevel differential gear with pluggable axles. RC-plate with receiver box.To complete the models all merchantable servos and radio control systems are suitable. The RTR version comes with complete factory installed rc-system, including Ni-Cads! The car comes with an unpainted body shell.The FG 5164 decor sheet is not included!Also available painted in the shop selection!Dimensions: Length: 840 mm Width: 395 mm Height: 250 mm Wheelbase: 465 mm HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount bigCNC machined alloy engine mount, direkt replacement for the stock plastic part, heat and tweak resistant. They come with all necessary hardware included. Value: 64,95 EUR Alloy spur gear carrierUse for 39T - 44 teeth spur gears.Value: 39,90 EUR Ball bearing set, sealed, set of 14The seal rings on sealed ball bearings keep dirt and dust out of the bearings. They are therefore particularly suitable for use in dirty and dusty environments.Value: 59,90 EURTotal value: 227,35 EURTouring cars in action!Painting tips:
The Wheelbase of the WB535 version is 60 mm longer. This modification improved the directionally stability as well as further driving qualities significantly. In addition parts of the 4WD Monster models were assembled in order to make a conversion to a 4WD model possible with low efforts. According to the large tires this model can be driven almost everywhere. The 26 cm³ engine provides sufficient power. Driving fun as well as tremendous looks are the prime characteristics of these models.The body shell comes yellow or black. A decal set with writings for further decoration is enclosed in the delivery.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Technical description:The undercarriage of the Monster models is built on a 4 mm angled alloy plate. All borings for fixa- tion of the chassis parts at the bottom side are countersunk in order to prevent the screw heads from sticking out. At the front axle you have the possibility to adjust toe-in or toe-out as well as the wheel camber through track rods with right-hand/left-hand thread. The wheel camber of the rear wheels can be adjusted individually through adjusting screws with right-hand/left-hand thread. Four large-volume oil-pressure shock absorbers are mounted at the lower double wishbones of front and rear axle, these are able to absorb larger shocks of jumps to a great extent and care for an optimal road grip. All rotating drive components are supported by ball bearings. Highly stressed steel parts such as rear gearwheels, differential gears and drive components are hardened. Fuel tank and ra- dio control parts are protected through alloy plates at the sides. The body parts are made of coloured or respectively clear polycarbonate. The Monster tires with tire inserts are glued on chrome-plated rims.The models are equipped with a powerful 26 cm³ combustion engine with ready-for-use oiled air fil- ter. The engine runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-start system the engine can be started without any difficulties.The pictures may display the car with some optional items which are not included, like bed-mounted rollbar, lights, front bumper or mirrors. These items can be added in the drop down menus.The RTR version is delivered with assembled and preset radio control system and rechargeable batteries. To complete the non-RTR version all popular servos and radio control sys- tems are suitable.Dimensions: Length: 780 mm Width: 510 mm Height: 350 mm Wheelbase: 353 mm
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).