GPM 66275/01 Front cardan shaft for nearly all FG 4WD models
Product number:
gpm_66275_01
EAN:
4058575041306
Product information "GPM 66275/01 Front cardan shaft for nearly all FG 4WD models"
Fits all FG 4WD cars (except FG Leopard!)
Lost drive shafts are a thing of the past!
Universal drive shafts allow for higher drive angles than dog bones or ball drives. This makes them a better choice for for wheel-side applications on front axles, where the angles of the steering and suspension meet.
GPM universals for ball drive can be disassembled and therefore repaired or rebuilded if necessary. The center pin (No.: < href="https://rc-car-online.de/en/products/gpm_66275_02-gpm-66275-02.html">66275/02) of the GPM universal joint is secured by a grub screw, which should be installed using a medium strength screw locking compound (66275/02).
Therefore the joint can be easily rebuilded by replacing the center pin for cheap and will be good as new again.
The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit.
Ball drives run significantly smoother and with less wear than normal dog bones with pins.
Lost drive shafts are a thing of the past!
Universal drive shafts allow for higher drive angles than dog bones or ball drives. This makes them a better choice for for wheel-side applications on front axles, where the angles of the steering and suspension meet.
GPM universals for ball drive can be disassembled and therefore repaired or rebuilded if necessary. The center pin (No.: < href="https://rc-car-online.de/en/products/gpm_66275_02-gpm-66275-02.html">66275/02) of the GPM universal joint is secured by a grub screw, which should be installed using a medium strength screw locking compound (66275/02).
Therefore the joint can be easily rebuilded by replacing the center pin for cheap and will be good as new again.
The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit.
Ball drives run significantly smoother and with less wear than normal dog bones with pins.
Login
Accessories / Spare parts
Genuine GPM spare/option part. Set of four axle pins and M3 x 8 mm grub screws. With 3 mm wide x 0.4 mm deep flat section.Dimensions:Diameter: approx. 2,97 mmLength: approx. 16,85 mmContents:1 set
Similar products
Genuine HT spare/option part. The best solution for drive shaft positioning, can be used with ball drives or regular "dog bones" as well.The springs will be simply inserted into the drive cups.DImensions:Diameter: 11 mmHeight: 8 mmContents:4 piece
Genuine HT spare/option part. Protect ball drive as well as cardan drive against dirt. For FG and Carson ball drives, fits standard dogbones as well.Contents:2 pieces
Genuine HT spare/option part. Dimensions:A = 5 mmB = 6 mmC = 8 mmD = 13 mmContents:2 pieces rose joints4 pieces conical spacers
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)17 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 17 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
Genuine HT spare/option part.Wheel squares made of high-strength aluminum, hardened, with two M6 mounting threads Suitable for most 1/6 and 1/5 rc-cars. Through the use of two 6 mm screws a significantly higher retention force is achieved. Yet it is still recommended to use medium strength thread lock (link y0114)! The hard anodizing (HART-COAT) guarantees much lower wear of the squares! Especially recommended when using wheel mounted brake discs! Four 3x16 dowel pins per square are included which prevent the squares from spinning in the rim. Press fitting them into the wheel squares is optional. The 12, 14 and 17 mm wide squares feature a groove for inserting a C-clip (link 6106/05), which acts as a guide for the brake disk. The narrow 9.5 mm wide squares dont need a clip; the close sitting rim will guide the disk. Measures18 mm square (wheel drive!)14 mm wide, 8.0 mm diameter axle boretwo M6 mounting threads The set includes 2 pieces of 14 mm wide wheel squares and 4 pieces each of M6 grub screws and 3x16 dowel pins.Contents:2 pieces
FG Set price: 163,25 EURFits all FG 4WD cars (except FG Leopard/ TR-4!) Lost drive shafts are a thing of the past! Universal drive shafts allow for higher drive angles than dog bones or ball drives. This makes them a better choice for for wheel-side applications on front axles, where the angles of the steering and suspension meet.GPM universals for ball drive can be disassembled and therefore repaired or rebuilded if necessary. The center pin (No.: 66275/02)of the GPM universal joint is secured by a grub screw, which should be installed using a medium strength screw locking compound (y0114).Therefore the joint can be easily rebuilded by replacing the center pin for cheap and will be good as new again.The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins.The GPM universal drive shaft set includes everything for the conversion of your FG 4WD.Set includes:Quantity:DescriptionPart number2 piecesUniversal drive shaftFG 662752 piecesDifferential ball drive cupGPM 6069/022 piecesDriveshaft booty10046 piecesSteel ballGPM 7080/022 piecesDrive shaft spacer springy1218
federn_dirt_m Version:
y0323/05 - M15, blue
Progressive tuning springs, will fit the standard red and the thick silver shocks on FG offroad cars. The rear springs will also fit Hurrax shocks. All springs have an internal diameter because of the manufacturing progress: 21 up to 21,5 mm. Available in several versions: For the front on FG 2WD buggies:y0322/01 - M1, 2,1 x 50 mm, yellowy0322/02 - M2, 2,2 x 50 mm, orangey0322/03 - M4, 2,4 x 50 mm, purpley0322/04 - M5, 2,5 x 50 mm, blueFor the rear on FG buggies, front and rear on FG monster cars and 4WD buggies:y0323/01 - M11, 2,1 x 90 mm, yellowy0323/02 - M12, 2,2 x 90 mm, orangey0323/03 - M13, 2,3 x 90 mm, redy0323/04 - M14, 2,4 x 90 mm, purpley0323/05 - M15, 2,5 x 90 mm, bluey0323/06 - M16, 2,6 x 90 mm, blackFor the front on FG buggies:y0324/01 - M01, 2,1 x 60 mm, yellowy0324/02 - M02, 2,2 x 60 mm, orangey0324/03 - M03, 2,3 x 60 mm, redy0324/04 - M04, 2,4 x 60 mm, purpley0324/05 - M05, 2,5 x 60 mm, bluey0323/06 - M16, 2,6 x 90 mm, blackContents:2 pieces
Genuine HT spare/option part.Alloy a-arm front upper for Off-Road Buggy 4WD RTR, Off-Road Beetle 4WD RTR and Monster-/ Stadium- Modelle 4WD RTR, 4WD Porsche and Mini. Replacement for FG item No.: 66266Contents:1 piece
Aluminum front shock tower for FG Off-Road Buggy and Sportsline 4WD, replaces stock plastic part FG #66287.Stock mounting hardware will be re-used.
federn_dirt_m0 Version:
y0324/05 - M05, blue
Genuine HT spare/option part. Progressive tuning springs, will fit the standard red and the thick silver shocks on FG offroad cars. All springs have an inner diameter of 21 mm.Available in several versions.For the front on FG buggies:y0324/01 - M01, 2,1 x 60 mm, yellowy0324/02 - M02, 2,2 x 60 mm, orangey0324/03 - M03, 2,3 x 60 mm, redy0324/04 - M04, 2,4 x 60 mm, purpley0324/05 - M05, 2,5 x 60 mm, blueContent:2 pieces
Alternative: y2002 Alloy a-arm, front upper FG 4WD - Fits FG Leopard 4WD und Sportsline onroad 4WD with 510mm wheelbase.Does not fit FG Leopard 2WD und Sportsline onroad 4WD with 530mm wheelbase.
Genuine FG spare/option part. Set contents front lower wishbones, rose joints, screws.Suitable for Off-Road Buggy 4WD RTR, Off-Road Beetle 4WD RTR and Monster/ Stadium models 4WD RTR, 4WD Porsche, 4WD Porsche and Mini.Contents:2 pieces
Customers also viewed
FG Set price: 163,25 EURFits all FG 4WD cars (except FG Leopard/ TR-4!) Lost drive shafts are a thing of the past! Universal drive shafts allow for higher drive angles than dog bones or ball drives. This makes them a better choice for for wheel-side applications on front axles, where the angles of the steering and suspension meet.GPM universals for ball drive can be disassembled and therefore repaired or rebuilded if necessary. The center pin (No.: 66275/02)of the GPM universal joint is secured by a grub screw, which should be installed using a medium strength screw locking compound (y0114).Therefore the joint can be easily rebuilded by replacing the center pin for cheap and will be good as new again.The GPM drive parts are made of high quality spring steel and due to its elasticity provide high impact resistance and extreme stability. Ground bearing seats ensure maximum accuracy of fit. Ball drives run significantly smoother and with less wear than normal dog bones with pins.The GPM universal drive shaft set includes everything for the conversion of your FG 4WD.Set includes:Quantity:DescriptionPart number2 piecesUniversal drive shaftFG 662752 piecesDifferential ball drive cupGPM 6069/022 piecesDriveshaft booty10046 piecesSteel ballGPM 7080/022 piecesDrive shaft spacer springy1218
Typical featuresLow inner resistance with high MPVHigher energy density with lower weightLonger lifecycle under proper usage, up to 200 timesFor LiPo batteries, the peak amp rate is usually twice the continuous crateCan be charged with 5C when time is criticalRecommended charge with 2 3C (max. 3C)Spezification:Tension: 3S / 11,1VCapacity mAh: 3300Case: SoftCable cross section: 12AWG/3,3Length +/- 5 mm: 135 mmWidth +/- 1,5 mm: 45 mmHeight: +/- 1,5 mm: 25 mmWeight +/- 10g: 300gCont. current: 60C (115,5A)Contents:1 piece
y0882 Version:
y0882/02 Aluminium version+ 10EUR
Aluminum or steel balljoints for replacement of the stock plastic units on the a-arms of all FG cars except Formula 1. Alloy:A = 5 mmB = M8C = 8 mmD = 17,5 mmE = 39 mmSteel:A = 5 mmB = M8C = 8 mmD = 16 mmE = 37,5 mmContent:8 x Aluminum or Steel balljoints, M8 r/h thread, 5mm bore diameter in the ball8 x low height nut, M8 r/h thread 16 x conical alloy spacer
Variants from €49.90*
7355/08 FG Carburetor type: Walbro WT603BStandard carburetor for Zenoah G230/260. Carb has integrated choke. Typ: Walbro WT603BHowever, we recommend using the WT668C instead of the WT603B.This also has a choke, but the manufacturing quality of the WT668C is better than the WT603B!Optional ball bearing of the throttle shaft can be selected from the shops menu.y1483 Walbro WT-1048 Racing carburetorPopular performance carburetor without choke; with 13.5 mm venturi diameter, especially suitable for large-displacement engines like the Zenoah G320.The stock throttle shaft has been replaced with the proper version required for car applications; including the throttle lever as well.All existing throttle linkages can therefore be connected as usual without modifications.This carburetor does not feature a primer bulb nor a connection for a return line. It is therefore only connected to the supply line from the tank, the return line of the tank has to be closed.Optional ball bearing of the throttle shaft can be selected from the shops menu.y1067 Walbro WT668C carburetorThe Walbro WT668C carburetor fits all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23cc up to over 30cc.The Walbro WT668C features an integrated choke with lever and a throttle shaft linkage lever. Optional ball bearing of the throttle shaft can be selected from the shops menu.Alternative: Walbro 603B also with chokey0251 Performance carburetor with accelerator pump type: WT-813AWalbro WT-813A carb with accelerator pump, improves low end response when the engine is tuned for maximum performance. 15.88mm bore, 12.7mm venturi. Ready for installation with modified shaft already installed. Fits Zenoah G230/240/260/270 engines and their CY/HPI Fuelie clones as well. Optional ball bearing of the throttle shaft can be selected from the shops menu.7855 FG Carburetor type: Walbro WT990Standard carburetor for Zenoah G240, G270 and G290. Typ: Walbro WT990 Optional ball bearing of the throttle shaft can be selected from the shops menu.y1016/051 Carburetor WT1107 G320RCGenuine Zenoah spare/option part. Standard part fits Zenoah G320RC.Optional ball bearing of the throttle shaft can be selected from the shops menu.
%
Incl. 2x TopTuning 3S 3100mAhFor those who want the biggest, baddest RC rock crawler ever, the legendary Axial® Honcho is now available on the 1/6 scale SCX6 4WD platform. With its 2-speed transmission and powerful Spektrum Smart electronics, this massive RTR is an absolute beast! Key Features Based on the legendary Axial® Honcho New vehicle option on the SCX6 platform Increased performance due to body design Two-speed metal gear transmission Spektrum Smart 3-channel radio and electronics The 1/6 scale Axial® SCX6 platform has taken RC rock crawling into a whole new dimension, armed with a huge amount of detail and high-performance functionality. Now, Axial has expanded the SCX6 lineup with an exciting 1/6 scale version of the insanely popular Honcho. Whether you're a fan of the original SCX10 Honcho, a rock crawling enthusiast, a large-scale aficionado, or all of the above, the Axial SCX6 Honcho 4WD RTR is sure to please. It's the biggest, baddest RC rock crawler ever!The SCX6 Honcho is engineered for extreme durability and performance, as shown by its AR90 axles with metal ring and pinion gears and front offset pumpkin. For optimal handling, the chassis has a three-link front and four-link rear suspension setup and metal links are used at all suspension points. The transmission offers high and low gears out of the box, with a Spektrum S614 metal gear high-torque servo included and installed for the two-speed linkage.Molded from high traction compound with an aggressive tread pattern, the massive, 7" tall, officially licensed Falken Wildpeak M/T tires provide excellent grip and ground clearance over dirt, rocks, and all other off-road surfaces. They're mounted on officially licensed Black Rhino Primm beadlock wheels for easy removal and replacement without gluing.With the included Spektrum DX3 radio, you'll enjoy the superior range, response, and interference resistance of exclusive DSMR® technology. Together with the installed Firma Crawler 120A Smart Sensored-Brushless ESC, it also comes ready to deliver the telemetry advantages of exclusive Spektrum Smart technology. Install a Spektrum Smart LiPo battery and you can view vehicle battery capacity on the transmitter's voltage level indicator. Outfit the DX3 with the optional BT2000 Bluetooth module, download the free Spektrum Dashboard app to your smart device, and you're ready to use more real-time Smart telemetry without needing on-board sensors or modules.Measuring over 2-1/2 feet long and topped off with a modernized Honcho body, the Axial SCX6 Honcho 4WD RTR is the rig that will take your rock crawling and climbing adventures to an exciting new level. Just add your choice of suitable battery and aim for the top! Features 1/6 scale chassis design is based on the proven SCX10 III Metal gear transmission comes configured for two speeds with high and low gears Durable three-link front and four-link rear suspension provides optimal handling AR90 axles feature metal ring and pinion gears Replica V8 engine cover adds to the realistic appearance Spektrum DX3 2.4GHz DSMR® radio provides superior range, response, and interference resistance and is compatible with Smart technology Spektrum Firma 120A Smart Brushless Crawler ESC feeds telemetry data to the DX3 transmitter in real time Includes a powerful Spektrum S905 high-torque, large scale steering servo (also accepts larger 1/5 scale servos with the included adapter) Modernized Honcho body with rear tube cage includes interior detail High-traction, 7" tall, officially licensed Falken Wildpeak M/T tires are mounted on officially licensed Primm Black Rhino beadlock wheels SCX10 III Based Chassis DesignInspired by the proven SCX10 III, the SCX6 platform follows a similar design while increasing the size to meet large scale needs and expectations. 2-Speed Metal Gear TransmissionOut of the box, the SCX6 Honcho 4WD RTR is configured for two speeds with high and low gears. A Spektrum S614 Metal Gear High-Torque Servo is included for the two-speed linkage. This feature provides a true crawling gear ratio while also allowing you to shift for more speed. AR90 AxlesThe AR90 axles feature metal ring and pinion gears with a front offset pumpkin. The 3-piece front axle accommodates optional aluminum carriers and steering knuckles. "Hi-steer" steering knuckles raise the steering tie rod for increased ground clearance. The rear axle can be set up for optional rear steering. Replica V8 Engine CoverThe molded engine cover captures the look of a modern V8 engine. It not only enhances the scale realism but also serves as the ESC mount and receiver box cover. 3-Link Front/4-Link Rear Suspension The SCX6 suspension geometry matches the SCX10 III with metal links used at all suspension points for durability. 1/6 Scale Steering ServoSteering is controlled by a Spektrum S905 high-torque, large scale servo. The servo mounting location will also accept an optional 1/5 scale servo if you choose to modify your rig. Spektrum Sensored Brushless Rock Crawling ESCIncluded and installed, the Spektrum Firma 120A Smart Brushless Crawler ESC provides throttle input to the massive Firma 1200Kv Sensored Brushless Motor. The motor itself weighs in at 1.75lb (.780kg) and gives this beast enormous power and realism! Officially Licensed Falken Wildpeak M/T TiresThe 7" tall, officially licensed Falken Wildpeak M/T tires are molded from a high traction compound and feature an aggressive tread pattern. They provide excellent grip and ground clearance over dirt, rocks, and other off-road surfaces for nonstop climbing and crawling. Officially Licensed Black Rhino Primm Beadlock WheelsThe SCX6 Honcho crawler's officially licensed Black Rhino Primm beadlock wheels add realism and allow easy tire removal and replacement without gluing. In The Box (1) 1/6 SCX6 Honcho 4WD RTR (1) Spektrum DX3 Smart DSMR® 3-Channel Radio with SR515 receiver (1) Spektrum Firma 120A Brushless Smart Crawler ESC (1) Spektrum Firma 1200Kv Sensored Brushless Crawler Motor (1) Spektrum S905 High-Torque 1/6 Scale Steering Servo (1) Product Manual (4) AA Transmitter Batteries