Filter element HT-Airbox, y19025 - 1pce.

This carburetor supoort sits beneath the air filter and prevents therefore widely arising vibrations.

For the smaller K&N filter

Genuine Carson spare/option part. Set includet:- B091-97 Air filterContents:1 set

With complete RTR equipment y1382 Original Maxi-Pin 1/6 offroad competition tire For an additional charge you can also select the HT-EDITION above. A great tuning offer for your new FG Marder. The standard price for the individual parts is €227.35. These tuning parts not only look great, but they also make your model more reliable.HT-Edition?HT-Edition means: this version comes with a big set of spare / option parts included.Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount bigCNC machined alloy engine mount, direkt replacement for the stock plastic part, heat and tweak resistant. They come with all necessary hardware included.Value: 64,95 EURAlloy spur gear carrierUse for 39T - 44 teeth spur gears.Value: 39,90 EURBall bearing set, sealed, set of 14The seal rings on sealed ball bearings keep dirt and dust out of the bearings. They are therefore particularly suitable for use in dirty and dusty environments.Value: 59,90 EURTotal value: 227,35 EURThe legendary 1/6 FG Marder 2WD Off Road Buggy! For many years the ideal entry into the elite class of radio controlled cars! The large-scale car with tough 26 cc engine is operated with normal 2-stroke gas. A 800 cc tank gives almost an hour of driving fun! For the FG Marder theres a wealth of option parts, most of them are not exactly a must, but make infinitely more fun! The FG Marder comes with completely installed remote control. Just fuel up, start the engine and drive off.Features:The model is built on an angled 4 mm chassis plate. All screws on the bottom are countersunk with no protruding heads. Double a-arms front and rear axle with 4 high volume oil-filled shock absorbers ensure optimum traction.All rotating parts are supported by ball bearings. Secondary spur gears, bevel gears inside the differential and all drivetrain parts are case-hardened. Rocker panels protect the car against contamination from below. The model is equipped with a powerful 26 cc engine. It needs a regular 2-stroke petrol/oil mix (available at every gas station). The integrated pull starter allows for easy engine starts without additional equipment.Dimensions: Length: 690 mm Width: 420 mm Height: 270 mm Wheelbase: 475 mm

Genuine FG spare/option part. Screw retention medium for securing and sealing of screws, nuts, bolts a.s.o. Also suitable for galvanized parts. Temperature stability: between -50° to 150°C.Content:1 piece / 35g

Normal price: 249,90 EUR Tuning front disk brake system for the HPI Baja 5B/SS/5T/5sc, the conversion kit includes all necessary parts. The brake includes the finest parts available for a cable brake and has the following features: * uses existing mounting points for all parts * brake pads and 70 mm diameter stainless rotors made by RS-5, the best performing combination available * hardened stud bolts for the brake pads * billet brake levers, no tweak and best transfer of servo power * ultraflex bowden cables * brake cams run in hardened steel bushings and brass guide plates (miniature bearings don't last in offroad cars) * billet alloy bowden cable support block with adjustment screws * billet alloy bowden cable mounts at the calipers * pre-assembledOn a 5T the stud bolts which hold the brake pads will interfere with the ribs in the rim. However, modifying the rim or swapping the stud bolts for long csh screws allows for installation on a 5T.Spare parts for this brake as a PDF-file with spare part numbersWe highly recommend the installation of a stronger throttle servo to take full advantage of this brake system. The is an excellent choice.