FG Sportsline 2WD-510 with Mini Cooper body shell, 23cm³ Engine HT-Edition

The Sportsline quality at a reasonable price for beginners. For rookies and all those who simply just want to have fun and drive a DTM Audi, Mercedes or a fast Porsche. The Sportsline series is ideal for car modellers whose main focus is not just the chassis, but rather the combination of chassis and body shell.Technical description:The model has a 510 wheelbase. The models are built on a 4mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in. Further equipment points are front disk brakes, differential gear, easy-running FG ball drive, alloy brake calliper with big brake disk, stabilizer bar front and rear, tuned pipe muffler, Evo gas tank, rear brace, 24T steel pinion, spark plug cap suppression cover, latest version (Evo) oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The models are equipped with a powerful 23ccm combustion engine. The engine needs a 2-stroke petrol oil mixture. One tank filling gives you about 45 minutes driving fun. The power is transmitted over the well-tried system: from the engine over the 2-block clutch over radial tooth wheels on to the rear axle which is equipped with the bevel differential gear with pluggable axles. RC-plate with receiver box.To complete the models all merchantable servos and radio control systems are suitable. The RTR version comes with complete factory installed rc-system, including Ni-Cads! The car comes with an unpainted body shell.Dimensions: Length: 780 mm Width: 405 mm Height: 250 mm Wheelbase: 510 mm HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount bigCNC machined alloy engine mount, direkt replacement for the stock plastic part, heat and tweak resistant. They come with all necessary hardware included. Value: 64,95 EUR Alloy spur gear carrierUse for 39T - 44 teeth spur gears.Value: 39,90 EUR Ball bearing set, sealed, set of 14The seal rings on sealed ball bearings keep dirt and dust out of the bearings. They are therefore particularly suitable for use in dirty and dusty environments.Value: 59,90 EURTotal value: 227,35 EURTouring cars in action!Painting tips:

The Sportsline quality at a reasonable price for beginners. For rookies and all those who simply just want to have fun and drive a DTM Audi, Mercedes or a fast Porsche. The Sportsline series is ideal for car modellers whose main focus is not just the chassis, but rather the combination of chassis and body shell.Technical description:The model has a 510 wheelbase. The models are built on a 4mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in. Further equipment points are front disk brakes, differential gear, easy-running FG ball drive, alloy brake calliper with big brake disk, stabilizer bar front and rear, tuned pipe muffler, Evo gas tank, rear brace, 24T steel pinion, spark plug cap suppression cover, latest version (Evo) oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The models are equipped with a powerful 23ccm combustion engine. The engine needs a 2-stroke petrol oil mixture. One tank filling gives you about 45 minutes driving fun. The power is transmitted over the well-tried system: from the engine over the 2-block clutch over radial tooth wheels on to the rear axle which is equipped with the bevel differential gear with pluggable axles. RC-plate with receiver box.To complete the models all merchantable servos and radio control systems are suitable. The RTR version comes with complete factory installed rc-system, including Ni-Cads! The car comes with an unpainted body shell.Dimensions: Length: 780 mm Width: 405 mm Height: 250 mm Wheelbase: 510 mm Touring cars in action!Painting tips:

y0557 Zenoah G230RC, with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge.y1009 Zenoah G240RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y0553 Zenoah G260RC with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)This is the G260 in the 26 cm³ version.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y1011 Zenoah G270RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% wider- New carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter are optionally available at additional charge. 7800 Zenoah G290RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5ccm cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.Zenoah G320RC with Walbro WT 1107 carburetor (also available in the ball-raced version through the shop's options menu)With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT 1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.

With complete RTR equipment y1382 Original Maxi-Pin 1/6 offroad competition tire The legendary 1/6 FG Marder 2WD Off Road Buggy! For many years the ideal entry into the elite class of radio controlled cars! The large-scale car with tough 26 cc engine is operated with normal 2-stroke gas. A 800 cc tank gives almost an hour of driving fun! For the FG Marder theres a wealth of option parts, most of them are not exactly a must, but make infinitely more fun! The FG Marder comes with completely installed remote control. Just fuel up, start the engine and drive off.Features:The model is built on an angled 4 mm chassis plate. All screws on the bottom are countersunk with no protruding heads. Double a-arms front and rear axle with 4 high volume oil-filled shock absorbers ensure optimum traction.All rotating parts are supported by ball bearings. Secondary spur gears, bevel gears inside the differential and all drivetrain parts are case-hardened. Rocker panels protect the car against contamination from below. The model is equipped with a powerful 26 cc engine. It needs a regular 2-stroke petrol/oil mix (available at every gas station). The integrated pull starter allows for easy engine starts without additional equipment.Dimensions: Length: 690 mm Width: 420 mm Height: 270 mm Wheelbase: 475 mm

Competition-OnRoad RC car with the latest technical developments. Unique among the large scale models. New stabilizer bar construction front and rear. Ball stabiliszers or frame stabilizers can be used (accessories). 10 mm thick chassis made of T7075 aluminium with cut-outs for weights (also under the tank) and grooves in the front area. This allows the vehicle to be perfectly adapted to the track or the driver. The engine is now again bolted to the chassis for more stiffness. Optimally designed wishbones on front and rear suspension. Reinforced and with toe-in adjustability, which is performed via aluminum wedges. Front upper wishbone for more adjustment possibilities. All gears with fine pitch.Since 1997, i.e. since the beginning of the 1:5 RC car scene, FG Modellsport has been represented with team drivers worldwide at national and international competitions. With the Competition-EVO series, FG won most world championships and almost all European championships. Content Top suspension with 10 mm T7075 aluminum chassis plate Zenoah G230RC Engine Adjustable Tuning Clutch Air filter / Airbox Tuned pipe system Front and rear hydraulic brakes Differential Large volume shock absorbers, black anodized Wheels and rims

The Sportsline quality at a reasonable price for beginners. For rookies and all those who simply just want to have fun and drive a DTM Audi, Mercedes or a fast Porsche. The Sportsline series is ideal for car modellers whose main focus is not just the chassis, but rather the combination of chassis and body shell.Technical description:The model has a 510 wheelbase. The models are built on a 4mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in. Further equipment points are front disk brakes, differential gear, easy-running FG ball drive, alloy brake calliper with big brake disk, stabilizer bar front and rear, tuned pipe muffler, Evo gas tank, rear brace, 24T steel pinion, spark plug cap suppression cover, latest version (Evo) oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The models are equipped with a powerful 23ccm combustion engine. The engine needs a 2-stroke petrol oil mixture. One tank filling gives you about 45 minutes driving fun. The power is transmitted over the well-tried system: from the engine over the 2-block clutch over radial tooth wheels on to the rear axle which is equipped with the bevel differential gear with pluggable axles. RC-plate with receiver box.To complete the models all merchantable servos and radio control systems are suitable. The RTR version comes with complete factory installed rc-system, including Ni-Cads and charger! The car comes with an unpainted body shell.Dimensions: Length: 890 mm Width: 405 mm Height: 250 mm Wheelbase: 510 mm Touring cars in action!Painting tips:

Inklusive: Spektrum 780 KV Brushless Motor und Spektrum 160 Amp ESC Spektrum™ Firma® 160 Amp Brushless SMART ESCDer Regler ist wasserdicht, vollständig programmierbar und mit einem Hochstrom-IC5-Stecker versehen. Der Regler funktioniert mit den meisten brushless Motoren und ist mit LiPo und NiMH Akkus kompatibel. Die SMART-Technologie liefert Informationen wie Batteriespannung, Drehzahl, RX-Pack-Spannung und Geschwindigkeit direkt vom ESC, wenn das ESC mit der Spektrum Dashboard-App verwendet wird.  80+ KMH Spektrum Firma 4-Pol 780Kv Brushless MotorDer brushless Regler und Motor bieten unglaubliche Leistung mit einem 8S LiPo (nicht im Lieferumfang enthalten), und ermöglichen Geschwindigkeiten von über 80 KMH. Zur komplementierung des HPI Baja 5B wird noch die RTR-Austattung (Fernsteuerung, Servo), Fahrakku benötigt. Bauen Sie Ihren eigenen authentischen HPI Baja 5B Flux! wir haben auf euch gehört, der einzige originale HPI Baja 5B ist als Bausatz zurück! Diese HPI SBK-Kollektion besteht aus einem elektrisch und einem kraftstoffbetriebenen Modell. Als der HPI Baja 5B Buggy zum ersten Mal vorgestellt wurde, waren große RC-Modelle sehr teuer und für den durchschnittlichen RC-Bastler ziemlich schwierig, diese fantastische Größe zu erleben.Durch die Verwendung hochbeständiger Teile und innovativer Designmerkmale brachte HPI neuen Enthusiasten Offroad-Fahrzeuge im großen Maßstab und läutete eine neue RC-Ära ein! Jetzt können Sie diese Legende nachbauen und erleben! Erleben Sie den Nervenkitzel und die Aufregung, ein Auto zu bauen, das am Ende über 80 cm (fast 32 Zoll) lang und fast 10 kg (über 21 lb) wiegt! Wählen Sie Ihren eigenen Sender, Lenkservo, Motor, Controller und Batterien!Mit extra starken Antriebskomponenten wie dem Viskose-Drehmomentdifferential, super haltbaren Verbundzahnrädern mit interner Dämpfung und einem Vollmetall-Antriebsstrang ist das HPI Baja 5B Flux einsatzbereit. Der HPI Baja 5B SBK ist außerdem mit übergroßen und superstarken Aufhängungsteilen ausgestattet, mit großartiger HPI-Haltbarkeit! Mit seiner fachmännisch konstruierten geformten Verbundstoffaufhängung plus extra langen einstellbaren HD-Stoßdämpfern und soliden dreiteiligen Nylon-Beadlock-Rädern ist dieser Baja 5B SBK bereit für Rennen mit voller Geschwindigkeit auf jeder Offroad-Strecke! Das 4mm dicke Monocoque-Chassis aus 6061er Aluminium verleiht dem HPI Baja 5B den klassischen Look eines Wüstenrennbuggys. Präzise in Form gebogen, um maximale Festigkeit zu erreichen, bildet das Chassis die Befestigungspunkte für Motor und Aufhängung und bildet das Rückgrat des Autos. Für eine präzise Lenkung sorgt eine doppelte Zahnstange mit Ritzel und Nockenwellen-Servo-Saver. Aluminiumteile sind in kühlem Bronze eloxiert und die klassische Baja Desert Racer klare Polycarbonatkarosserie ist im HPI Baja SBK-Kit enthalten, bereit für Ihr eigenes Farbschema mit Ihrer Lexan-Farbe Ihrer Wahl Ihrer Lexan-Farbe Ihrer Wahl.RACING CHASSIS DESIGN & LAYOUTDas schmale Monocoque-Chassis aus steifem 4mm 6061er Flugzeugaluminium verleiht dem HPI Baja 5B SBK eine klassische Desert Race Buggy-Optik und extreme Steifigkeit und Langlebigkeit. Das U-förmige Chassis ist hinten mit einer dicken Kunststoff-Unterfahrschutzplatte geschützt, um Motor und Antriebsstrang zusätzlich zu schützen. Der Rohr-Überrollkäfig besteht aus schlagfestem Nylon und hat ein echtes Aluminiumdach, um den klassischen Look fortzusetzen. Der Überrollkäfig ist voll funktionsfähig und schützt Motor und Innenraum vor Crashschäden. Der Überrollkäfig, die Radiobox, die Karosserieteile, der Kotflügel, der Unterboden und das Getriebe sind alle mit Schnellzugriffsclips für eine einfache Wartung montiert.Beim Bau eines HPI SBK (Self Build Kit) haben Sie völlig freie Wahl. Zur Fertigstellung wird noch benötigt: Fernsteuerung mit Servo Fahrakkus (je 2x 3S oder 2x 4S) Ladegerät für Fahrakkus Zwei Dosen Spezifikationen: Offroad-Buggy-Bausatz im Maßstab 1:5 Bereit für Ihre 6S- oder 8S-LiPo-Elektronik Freie Wahl der Elektronik Geschlossene RC-Box Transparente Baja-Kapuze Einstellbare HD-Stoßdämpfer Monocoque-Fahrgestell Niedriger Schwerpunkt für überlegenes Handling Langer Federweg Ölgefülltes Viskose-Differential All-Terrain-Reifen Beadlock-Räder mit Metalleinsatz Hintere Stoßdämpferbrücke aus Aluminium Schutzplatten aus Hartplastik Verstellbarer Heckflügel Schneller Zugriff auf alle kritischen Wartungspunkte Doppelte Kniehebellenkung Nockenwellen-Servo-Saver Rennspezifische Innensechskant-Hardware Bronze eloxiert Kompletter Satz gummierter Kugellager Spezifikationen Chassis: Gesamtlänge: 817 mm Höhe: 255 mm Breite vorne: 460 mm Breite hinten: 480 mm Spurweite für 395 mm Spurweite hinten: 400 mm Radstand: 570 mm Reihenhöhe: 76 mm Federweg vorne: 95 mm Federweg hinten: 100 mm Gewicht: 9,6 kg Einstellbarer vorderer Sturz Sturzeinstellung für: mit Shims Sturzeinstellung hinten: mit Schraube Nachlauf für: einstellbar mit Unterlegscheibe; 22~25,5~29 Grad Fußleisteneinstellung für: mit Schraube Zehenspur hinten: fügt 0~4 Grad ein Flugzeugaluminium 6061 T6 Monocoque-Chassis Doppelquerlenkeraufhängung mit einstellbarem Rollzentrum vorne und hinten Antriebssystem: HD-Metallgetriebe mit abgedichtetem Getriebe Übersetzungsverhältnis: 8,382:1 Differential: Viskose Drehmomentsteuerung mit Silikonöl Stoßdämpfer: HD-Aluminium einstellbar Radtyp: 3-teiliges Beadlock-Design mit Metallnabe