BJ057/TB Upgrade ball joints with R/L thread turnbuckle for GPM alloy a-arms rear upper HPI Baja / Carson Wild GP Attack.

€19.80*

Available

Product number: bj_057_tb

EAN: 4058575136354

Product information "BJ057/TB Upgrade ball joints with R/L thread turnbuckle for GPM alloy a-arms rear upper HPI Baja / Carson Wild GP Attack."

Also suitable in combination with the standard plastic a-arms, these may need to be shortened by a few millimeters. Ball socket with M6 l/h female thread!

Content: 2 ball joints with turnbuckles

Content:

2 pieces

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Similar products

SBJ160, GPM steel tie rod set for HPI Baja, Carson Wild GP Attack, set

Complete steering rods and tie rod between steering servo and servo saver with steel turnbuckles. Dimensions: Hole to hole: 120mm Total length: 135mm

€29.90*

BJ057/BE Replacement ball joints for GPM alloy a-arms rear upper HPI Baja / Carson Wild GP Attack.

Also suitable in combination with the standard plastic a-arms. Ball socket with M6 female thread.Content:2 pieces

€12.90*

y1345 Drive pins, choice of sizes, e.g. for Losi, Mini and HPI cars

y1345 Size: y1345/03 - 4 x 24 mm

Genuine HT spare/option part. Hardened pins made of 100Cr6 steel for driveshafts, differentials, wheel drives and similar applications. Pack of ten. Sizes available:y1345/01: 4 x 18 mm, e.g. for Losi 5ive-T/Mini and HPI Baja differentials or HPI Baja layshafty1345/02: 4 x 20 mm, e.g. for Losi 5ive-T/Mini CVD jointsy1345/03: 4 x 24 mm, e.g. for Losi DBXL and HPI Baja wheel hexy1345/04: 5 x 24 mm, e.g. for Losi 5ive-T/Mini wheel hexContents:10 pieces

€4.90*

Details

y1183/04 Hardware set for wheel adapter FG rim to HPI car

Hardware set for wheel adapter FG rim to HPI car:y1183y1183/02y1183/03

€4.90*

y1183/01 Grooved pin 4x19 mm, replacement for HPI rim adaptor y1183, 5 pieces

Grooved pin 4x19 mm, replacement pins for HPI adaptor to install FG rims on HPI Baja cars.Diameter: 4 mmLenght: 19 mmDelivery contents: 5 pieces

€3.90*

y1183/02 FG rim to HPI model, drive rim adapter, separate for the front, 2 pcs.

Item N° y1183/02FG rim to HPI model, drive rim adapter, separate for the front, 2 pcs.These adapters are machined from gas nitrited steel and enable you to put standard rims with 18 mm square drive (FG, Carson, Lauterbacher a.s.o.) on the HPI Baja 5B/SS/T. The track width will be substantially increased.For a complete set covering front and rear axle you need part number y1183.This set includes rim adapters with installation hardware for the front axle only.Measures for front:Outer diameter: circa 17,59 mLength: circa 55,10 mm

€24.90*

BJ055/Ball, GPM Replacement front lower ball for HPI Baja, Carson Wild GP Attack, pair

Replacement balls for GPM a-arms BJ055

€4.90*

Customers also viewed

BJ057/BE Replacement ball joints for GPM alloy a-arms rear upper HPI Baja / Carson Wild GP Attack.

Also suitable in combination with the standard plastic a-arms. Ball socket with M6 female thread.Content:2 pieces

€12.90*

6027 FG Ball-and-socket joint 6mm with ball

Genuine FG spare/option part. Plastic ball joint Fits all FG cars.Dimensions:Thread size: M4Länge: 20 mmBall bore: 3 mmHeight: 8 mmContents:6 pieces

€14.50*

y0729 Gas-nitrited tuning clutch bell for HPI Baja, Carson Wild GP Attack models, 1 pce.

Gas-nitrited tuning clutch bell machined from high grade steel with a hole for easy clutch adjustment. Special vents remove dirt and clutch lining debris automatically, preventing it from accumulating in the clutch bell and causing premature wear to clutch bell and linings. They aid in cooling of the clutch bell as well.The clutch bell features a significantly reinforced wearing surface whichguarantees dimensional stability even under high loads!Since this clutch bell is single-piece machined from bar stock there is no weld bead on the inside of the face plate. The gained space allows now to use the adjustable GPM clutches Big Scale Extreme and Cross.Suitable for slot drive HPI Baja pinions, both stock using a 4mm bolt and aftermarket ones for 5mm bolts. Comes with M4 and M5 bolts included.

€49.90*

y1011 Zenoah G270RC with Walbro carburetor WT 990

26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:Quantity of cylinder mounting bolts increased from 2 to 4Improved strength of crankcaseAdded additional bearing on the PTO (clutch) side of crankshaftRedesigned shape of cylinder finsDimension of air intake port is 5% widerNew carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch and / or ball beard carburetor are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

€284.90*

y0740 Replacement silicone exhaust hose for Losi 5ive-T Jetpro

Genuine HT spare/option part. Spare part for the Jetpro Losi 5ive-T tuned pipe.Measures:Inside diameter: 28 mm Outside diameter: 37 mmWall thickness: 4 mmLength : 46 mmContents:1 piece

€7.90*

y19031/01 Silicone exhaust hose extrem reinforced 22/30 mm

Genuine HT spare/option part. Very strong, multiple glas fiber layers, nevertheless very stretchable. Resist maximum temperatures up to 250°C (482°F) from.Needs hose clamps with at least 35 mm inner diameter! Maße:Inside diameter: 22 mm Outside diameter: 30 mmWall thickness: 4 mmLength: 50 mmContents:1 piece

€9.90*

Details