Genuine ATOP spare/option part.CNC-machined from 6061-T6 aluminum by ATOP RC.Increases track width by 25 mm. Fits all versions of DBXL / DBXL-E / 2.0 (brushless and gas) and MTXL. 2 mm O-rings protect against drive pin loss.Set of four including O-rings, drive pins and closed wheel nuts (wrench size 24 mm!).Contents:1 set
Genuine ATOP spare/option part. Camber rods for Losi DBXL with center section cnc-machined from 6061 aluminum by ATOP. High grade all-metal ball joints at the pivot points provide zero backlash and strength. Fits front and rear.Attention: On a DBXL-E 2.0 these rods can only be used as camber rods, not as steering rods! Dimensions: Hole to hole: 117mm Total length: 135mm Contents:2 pieces
Genuine ATOP spare/option part. Front transmission mount for Losi DBXL cnc-machined from 6061 aluminum by ATOP.Through the use of aluminum, the problem of torn out threads (incl. the front bumper installation) is eliminated. At the same time the chassis section under the transmission is strengthened and the mounting points for the shock towers are reinforced.Comes with all mounting screws included.This is the new ATOP version with the additional mounting points between transmission housing and transmission bracket for a more secure connection of these parts.Old and new versions are fully compatible, regardless of whether they are made of aluminum or plastic. The parts therefore fit all versions of DBXL and MTXL in any combination.However, the use of the additional mounting points requires the new version of both transmission housing and bracket!Contents:1 piece This article is identical to the article in the video!
Genuine ATOP spare/option part. CNC-machined 6061 aluminum transmission case by ATOP, fits front and rear.Service life of ball bearings and ring & pinion will greatly benefit from the increased strength of this aluminum case. Comes with all mounting screws included.This is the new ATOP version with the additional mounting points between transmission housing and transmission bracket for a more secure connection of these parts.Old and new versions are fully compatible, regardless of whether they are made of aluminum or plastic. The parts therefore fit all versions of DBXL and MTXL in any combination.However, the use of the additional mounting points requires the new version of both transmission housing and bracket!Contents:1 piece This article is identical to the article in the video!
Genuine Atop spare/option part. Two pieces CNC-machined 6061-T6 aluminum spring perches for Losi DBXL. Direct replacement for the stock part (from set. # LOS 253006).Content:2 pieces
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum suspension arms for Losi DBXL. Set of four a-arms with plastic bushings for the hinge pins, all required nuts and bolts are included.Contents:2 pieces
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum chassis braces, for Losi DBXL 2.0.Compared to the stock plastic parts (from sets # LOS251115 and LOS251116) the higher strength of the aluminum parts noticeably increases the chassis rigidity.Contents:1 piece
Genuine ATOP spare/option part. One-piece CNC machined 6061-T6 aluminum spindles from ATOP, fits all Losi DBXL and MTXL versions, gas and brushless.Significantly more rigid than the stock plastic version, this part contributes to increased steering precision and directional stability. Stainless steel bushings for the King Pins are included.Comes with wheel bearings included. Contents:2 pieces
Genuine ATOP spare/option part. Steering rods for Losi DBXL-E 2.0 with center section cnc-machined from 6061 aluminum by ATOP. High grade all-metal ball joints at the pivot points provide zero backlash and strength. Dimensions: Hole to hole: 108mm Total length: 128mm Contents:2 pieces
Genuine HT spare/option part. Ball & socket tool with t-handle, special version for the ball joints.Fits Losi 5ive-T. 5ive-B, Desert Buggy XL, Desert Buggy XL-E, Monster Truck XL and the HPI Baja 5B and Baja 5R Ford Mustang.Contents:1 piece
Genuine ATOP spare/option part. One-piece CNC machined 6061-T6 aluminum spindles from ATOP, fits all Losi DBXL and MTXL versions, gas and brushless. Significantly more rigid than the stock plastic version, this part contributes to increased steering precision and directional stability. Stainless steel bushings for the King Pins are included.Comes with wheel bearings included. Contents:2 pieces
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum chassis braces, for Losi DBXL 2.0.Compared to the stock plastic parts (from sets # LOS251115 and LOS251116) the higher strength of the aluminum parts noticeably increases the chassis rigidity.Contents:1 piece
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum small rear chassis brace, only for Losi DBXL 2.0.Compared to the stock plastic part (from set # LOS251116) the higher strength of the aluminum part noticeably increases the chassis rigidity.Contents:1 piece
Genuine ATOP spare/option part. CNC-machined 6061-T6 aluminum large rear chassis brace, only for Losi DBXL 2.0.Compared to the stock plastic part (from set # LOS251116) the higher strength of the aluminum part noticeably increases the chassis rigidity.Contents:1 piece
The original DBXL-E set the world on fire as the go-to vehicle for large scale bashers and enthusiasts alike. Its agile handling, out of the box speeds and durability make it a fan favorite. Now the Losi® DBXL-E 2.0 continues to build on the legendary status! Known worldwide for their dominance in the gas 1/5 market, especially with the 5IVE-T 2.0, Losi has built the DBXL-E 2.0 to be cleaner and easier to use, but with performance and speed that outruns the competition. At home in any environment from dirt to pavement, wet or dry, especially with its 4WD drivetrain with larger 5mm drive pins, the desert buggy makes sure all the power is put to the ground. Drivers stay in control with a DX3 transmitter, a Spektrum SR6100AT 6 Channel AVC® Telemetry Surface Receiver, and scale-to-size Maxxis Creepy Crawler LT tires. This desert buggy features all the technological advances drivers demand including the Spektrum Firma® 160 Amp Brushless SMART ESC and Spektrum Firma 4-Pole 780Kv Brushless Motor allowing you to hit 50+ MPH with an 8 cell LiPo battery. Finally, the DBXL-E 2.0 has a Losi and Fox Shox race-inspired motorsports themed livery for that true off-road look. You get all this and more from the brand that represents the pinnacle of performance. Spektrum Firma® 160 Amp Brushless SMART ESCThe ESC is waterproof, completely programmable, and comes pre-wired with a high-current IC5 connector. The ESC will work with most sensorless brushless motors and is Li-Po and Ni-MH compatible. The SMART technology provides information like battery voltage, RPM, RX pack Voltage, and Speed directly from the ESC when used with the Spektrum Dashboard app. 50+ MPH Spektrum Firma 4-Pole 780Kv Brushless MotorThe brushless ESC and motor provide wicked power with an 8s LiPo battery (not included) that will blaze speeds of 50+ MPH. Spektrum S906 1: 5-MetallgetriebeservoNeues 30-kg HV Hi-Torque Metallgetriebe-Servo. New Chassis Braces In addition to the chassis stiffening plate, we have also added an additional electric specific rear chassis brace that goes all the way up to the center diff mount to increase the rigidity of the chassis. Updated Front and Rear BulkheadsThe front and rear bulkheads have been updated to match the new gearboxes designed for the DBXL-E 2.0. Two additional mounting locations were added to the side of the bulkheads to keep the gearboxes from rocking up and down under acceleration and braking. This provides a more stable drivetrain, and increased overall durability. Aluminum Center Diff CupReturning from the original DBXL-E is the aluminum diff cup used in the center differential. Today"s brushless motors produce so much power, that you need to have the added strength and durability in the center diff that only an aluminum diff cup can provide. New Shocks with Laser Etched FOX Logo Shock CapsNew shock bodies with a lower aluminum cap that allows for easier maintenance of the shock seals for improved performance. Sometimes, it is about the details. New upper shock caps with laser etched FOX logo set off that race inspired look. MAXXIS Creepy Crawler Tires with Authentic Bead Lock WheelsGenuine MAXXIS creepy crawler tread pattern tires provide added traction and offer extra control so you can stop, turn and swerve like a pro. Have confidence your tires will never come unglued and make tires changes a breeze with authentic bead lock wheels. Aluminum Shock TowersWe couldn"t just stop at the shocks. The DBXL-E 2.0 gets all new Aluminum Shock Towers Front and rear with revised camber mounting locations for improved stability and handling. Heavy Duty DrivetrainIncreased the size of the out drives and drive shaft to support a larger 5mm drive pin for increased strength and durability. New Radio TrayAll new radio tray with sealed receiver box. The new radio tray allows for multiple steering servo configurations. Can be run as a single servo, or updated to run dual steering servos for maximum steering performance. New ESC MountTo create space for the larger battery trays, we needed to find a new home for the ESC. The ESC has been relocated to a mounting plate off the center differential. This allows for optimal weight distribution within the car, while increasing the air flow over the top of the ESC for better running performance. New Race Themed LiveryNew Fox Shox race inspired Motorsports themed livery for that true off-road look, along with an awesome Losi flame design trim scheme. Waterproof ElectronicsThe DBXL-E 2.0 is loaded with waterproof electronics including the receiver, servo and ESC. Everything is sealed against the elements allowing you to splash in the rain, spin in the mud and make tracks in the snow. It"s full-throttle freedom to run anytime, rain or shine LED Light BarThe roof mounted LED Light bar from the original DBXL-E returns to continue lighting the way for endless adventures. Spektrum DX3 Radio SystemThe Spektrum DX3 radio system offers advanced features like AVC control, a 3-position throttle limiting switch and travel adjust. It features exclusive DSMR® technology for superior range, response, and interference resistance. It's also fully compatible with the Smart telemetry potential provided by the vehicle's installed Spektrum Firma Smart 40A ESC/receiver, and has a convenient voltage level indicator for any Spektrum Smart batteries! The Full-Throttle Freedom of AVC® TechnologyThe receiver's built-in AVC® (Active Vehicle Control®) traction control system works behind the scenes, making hundreds of throttle and steering adjustments per second, so more of the motor's power is translated into ballistic speed and acceleration instead of just flying dirt. The patent-pending AVC system adds a level of performance that simply cannot be found with any vehicle from any manufacturer other than Horizon Hobby. Like traction control in your full-scale vehicle, you can activate or deactivate the system on the fly and adjust the level of stability based on driving conditions. Any RC vehicle can go fast and with AVC you can go faster while maintaining optimum stability in all driving conditionFeatures Spektrum Firma® 160 Amp Brushless SMART ESC Spektrum Firma 4-Pole 780Kv Brushless Motor Spektrum DX2E Active radio system with AVC® and new SR6100AT Receiver Spektrum S906 1/5th scale metal gear servo Waterproof Components Aluminum Shock Towers Aluminum Center Diff Cup New Radio Tray designed for use with single or dual steering servos. New Heavy Duty Drivetrain with 5mm drive pins New Electric Chassis specific chassis braces for increased durability and strength New ESC Mount Pinned Center Outdrive Cups New Gearboxes for improved drivetrain strength and stability New Steering Rack with helical servo saver design Updated Front and Rear Bulkheads Maxxis Creepy Crawler LT Tires Losi and Fox Shox race-inspired Motorsports themed livery Laser Etched FOX Logo Shock Caps Roof-mounted LED bar Dimensions Height: 317 mm Length: 844 mm Width: 495 mm Weight: 9,8 kg
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).