Skip to main content
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

AT-5T023 ATOP Aluminum front a-arms Losi 5ive-T/2.0

Product information "AT-5T023 ATOP Aluminum front a-arms Losi 5ive-T/2.0"

Genuine ATOP spare/option part.

Light weight design (108 grams each), CNC-machined from 6061-T6 aluminum by ATOP a-arms fits Losi 5ive-T front.
The chassis-side is wider than stock arms to bring the large longitudinal play at this point down to a reasonable level.

Bushings for the hinge pins guarantee low wear. On the wheel side floating stainless steel bushings allow for normal tightening of the c-hub screws.

Contents:
  • 1 set

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Alternatives

Average rating of 0 out of 5 stars

AT-5T023/024 ATOP Aluminum a-arms front and rear Losi 5ive-T/2.0
Genuine ATOP spare/option part.Light weight design (Total weight of all the wishbones is a mere 444 grams), CNC-machined from 6061-T6 aluminum by ATOP a-arms fits Losi 5ive-T front. The chassis-side is wider than stock arms to bring the large longitudinal play at this point down to a reasonable level.Plastic bushings for the hinge pins guarantee low wear. On the wheel side floating stainless steel bushings allow for normal tightening of the c-hub screws.Contents:1 set

€149.90*

Customers also bought

%

Average rating of 0 out of 5 stars

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters
Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€34.90* €42.90* (18.65% saved)

Similar products

Average rating of 0 out of 5 stars

AT-5T004 ATOP Aluminum closed wheel nuts Losi 5ive-T/2.0/B, Mini, DBXL/2.0 and MTXL
Genuine ATOP spare/option part.CNC-machined from 6061-T6 aluminum by ATOP. Closed design, thread size M18 x 1,5 for Losi 5ive-T/B, Mini, DBXL and MTXL. Wrench size 24 mm, may fit other cars as well.Contents:4 pieces

€22.90*

Average rating of 0 out of 5 stars

y0041 Aluminum spring perches for Losi 5ive-T/2.0/B and Mini shocks
Genuine HT spare/option part.Aluminum spring perches for Losi 5ive-T/B and Mini shocks; with slot for fast and easy change of shock springs. Direct replacement for the stock plastic part.Contents:2 pieces

From €19.90*

Average rating of 0 out of 5 stars

AREA-5T-018 Aluminum spring perches Losi 5ive-T/2.0/B and Mini
Genuine FG spare/option part.CNC-machined from 6061-T6 aluminum by Area RC.Contents:2 piece

€19.90*

Average rating of 0 out of 5 stars

AT-5T018 ATOP Aluminum spring perches Losi 5ive-T/2.0/B and Mini
Genuine FG spare/option part.CNC-machined from 6061-T6 aluminum by Atop RC. Contents:2 piece

From €14.90*

Average rating of 0 out of 5 stars

AT-5T015 ATOP Aluminum front transmission case Losi 5ive-T/2.0/B and Mini
Genuine ATOP spare/option part.Completely cnc-machined front transmission case from billet 6061-T6 aluminum by Atop. Service life of ball bearings and ring & pinion will greatly benefit from the increased strength of this aluminum case. It also ends the problem of stripped tread holes for the mounting screws. Weight:approx. 297 gramsContents:1 piece

€159.90*

Average rating of 0 out of 5 stars

AT-5T005 ATOP Aluminum axle extenders Losi 5ive-T/2.0/B, Mini, with closed nuts
Genuine ATOP spare/option part.CNC-machined from 6061-T6 aluminum by ATOP RC, increase track width for 25 mm and allow for the use of HPI 5T, Losi 5ive-T, 5ive-B and Mini rims. 5 mm o-rings protect against drive pin loss. Set of four inclusive o-rings, drive pins and closed wheel nuts (wrench size 24 mm!).Contents:1 set

€49.90*
%

Average rating of 0 out of 5 stars

AT-5T026 ATOP Aluminum spindles front for Losi 5ive-T/2.0/B and Mini
Genuine Atop spare/option part.CNC-machined 6061-T6 aluminum front spindles from Area RC; fits Losi 5ive-T/B and Mini. Significantly more rigid than the stock plastic partthese spindles improve steering precision and tracking.They also feature larger outer bearings (12 x 28 x 7 mm) than stock for higher load capacity. All four ball bearings are sealing bearings.Contents:2 pieces

€79.90* €89.90* (11.12% saved)

Average rating of 0 out of 5 stars

AT-5T006/007 ATOP Aluminum front and rear skid plate Losi 5ive-T/2.0 and Mini
Genuine ATOP spare/option part.CNC-machined from 6061-T6 aluminum by ATOP.Protects chassis plate and transmission case over rough terrain. Also reinforces the chassis plates narrow section in front of the gear case. Thickness: 4 mm, weight: complete 141 grams.Contents:1 set

€39.90*
%

Average rating of 0 out of 5 stars

AT-5T015/16 ATOP Aluminum front and rear transmission case Losi 5ive-T/2.0/B and Mini
Genuine ATOP spare/option part.AT-5T015 ATOP Aluminum front transmission case Losi 5ive-T/B and MiniCompletely cnc-machined front transmission case from billet 6061-T6 aluminum by Atop. Service life of ball bearings and ring & pinion will greatly benefit from the increased strength of this aluminum case. It also ends the problem of stripped tread holes for the mounting screws. Weight:approx. 297 gramsAT-5T016 ATOP Aluminum rear transmission case Losi 5ive-T/B and MiniCompletely cnc-machined rear transmission case from billet 6061-T6 aluminum by Atop. Service life of ball bearings and ring & pinion will greatly benefit from the increased strength of this aluminum case. It also ends the problem of stripped tread holes for the mounting screws. Set comes with bearing carriers included! We recommend to install the bearings using thread locking compound y0113. Bindulin silicone sealant y19015 is recommended for installing the bearing adaptors into the transmission case. Modification of the Atop bearing carriers is required when using HD differential drive cups y1477. Weight:approx. 418 gramsContents:1 set

€319.80* €349.80* (8.58% saved)

Average rating of 0 out of 5 stars

y0057 Ball & socket tool for Losi and HPI
Genuine HT spare/option part. Ball & socket tool with t-handle, special version for the ball joints.Fits Losi 5ive-T. 5ive-B, Desert Buggy XL, Desert Buggy XL-E, Monster Truck XL and the HPI Baja 5B and Baja 5R Ford Mustang.Contents:1 piece

€17.90*

Average rating of 0 out of 5 stars

y0722 Axle plugs for Losi 5ive-T/2.0, Mini
y0722 Quanity: y0722/01 - Set of 4
For sealing the axles on Losi 5ive-T and Mini cars, keeps debris out of the inner screws which secure the retainer pin. Set of 4 or set of 10 to choice.Can be used for Losi 5ive-T, Mini and HPI Baja cars.

€3.90*

Average rating of 0 out of 5 stars

LO5T055-ACC Spare bushings set for GPM/Losi 5ive-T front a-arms LO5T055, set
Bushings set for GPM front a-arms part no. LO5T055.

€17.99*

Customers also viewed

Average rating of 0 out of 5 stars

LOSB3222 Losi Center Coupler Boots and Clips for 5ive-T, TLR 5ive-B and Mini
Genuine Losi spare/option part. Fits losi 5ive-T, TLR 5ive-B and Mini. Dimensions grommet:total length: 53 mm, down to 38 mm compressibleinner diameter: shaft 6 mm, shaft intake 19 mm Dimensions clamping ring: RW 20 galvanized, burnished for 20mm grommets Contents2 x grommet4 x claming ring

€19.99*
Loading...
Upload in progress, please be patient ...
Shopware-Theme Development Shopware-Theme Development