8192 FG Front body BMW M4 DTM clear

Genuine FG spare/option part. The advantage of a one-way clutch over conventional or limited slip differentials is the combination of maximum propulsion and outstanding agility in the turns. This results in a 4WD vehicle with the quick turning-in of a 2WD while retaining the advantages of 4WD traction when accelerating out of corners.This applies to offroad and street cars alike.The inner races in the one-way clutch feature the internal spline drive to accept FG differential shafts. They are made of high strength steel, hardened and ground to very close tolerances. Combined with the large one-way clutches, this guarantees the transfer of the high maximum torque.Installation is pretty easy; the one-way clutch unit replaces the bevel gears in the diff including the satellite gear shaft and is inserted as a single piece into the differential case. You just have to take care that the side where the writing on the clutch can be seen goes to the left hand side (in the direction of travel).Fits FG-plastic differential case and HT- or FG-aluminum cases for non-self-locking differential versions.For vehicles not equipped with in-wheel brakes it should be noted that there will be no more braking action in front from the layshaft brake when running the one-way clutch as a front differentialOnly for 4WD models. Suitable for all differential housings except viscous and Powerlock diff.Contents:1 piece

Item N° 66520 Battery holder for Electro cars, 5 pcs.

Genuine FG spare/option part.Cooling fan for electric engine no.: 7900 FG Electric engine E-Power BL-730KV.

This pair of Tyres have the following use indications: VERY HIGH GRIP situation for very clean track. VERY HIGH GRIP situation for big asphalt. VERY HIGH GRIP situation for very high temperatures. This pair of Tyres have the following technical features: REVO treated profile for the maximum traction and the maximum lateral grip. Treated profile studied to maintain the tyre surface alway clean from rubber murble. Compound exclusively developped for model tyres. Inside belt flexible but very strong, vulcanized directly together with tyre compound. Insert foam with special material for high temperatures, for maximum stability and high drive precision. Spoked wheel moulded with special material for high temperatures for maximum grip and stability. Special gluing system 100% guaranteed.The main sizes for this tyre are: WHEEL fixing with square 18mm. TYRE outside diameter 118mm. WHEEL inside diameter 90mm. TYRE tota width 65mm. Note:The harder a tire compound - the longer it lasts, but the more moderate the performance.The softer a tire compound - the better the performance, but the lower the durability. Hint!As a rule, the same tires can be used for front and rear.If the vehicle tends to oversteer, this can be avoided by using a harder front tire!In wet conditions you should use a rain tire which offers maximum grip under these circumstances.With the use of Magic Rain, a tire traction compound, the grip can be further improved.Check your tires after driving! It can happen that a tire starts to detach from the rim, in this case you should glue this spot immediately with our tire repair kit (y0067), otherwise the tire could detach completely from the rim.So find out which tire is the best for you!

Alloy ring gear adaptor for FG, Smartech, Carson and many other cars. Contrary to the stock plastic adaptor the aluminum version is secured by set screws.There are three sizes available:y0048/01 - 47 mm outer diameter, fits 38 tooth ring gearsy0048/02 - 52 mm outer diameter, fits 39/40/41/42/43/44 tooth ring gears - Weight: 29 grammsy0048/03 - 60 mm outer diameter, fits 46T and 48T ring gears - Weight: 31 gramms

Genuine HT spare/option part.Alloy upright for a ball fastening at the upper wishbone. Adjustable at the lower wishbone (hinge pin), too. Fits the rear axle of all FG and Carson / Smartech 1/6 scale cars.Comes with adjustment clips and grub screws for the hinge pins included.Dimensions:Bearing seats: 22 x 7 mmHinge pin bore: 6 mmDistance wheel shaft/hinge pin: 25 mm Contents:2 pieces