Genuine FG spare/option part.This roll bar is just for looks, not for protection. It consists of aluminum tubes and plastic corner joints.Fits monster truck body shells.Dimensions double loop:Height: approx. 100 mmWide: approx. 230 mmDimensions kickers section:Length: approx. 190 mmWidth: approx. 120 mmContents:1 set
Genuine Champion spare/option part.OEM spark plug for Zenoah G230/240/260/270/290/320.Ideal too for PT, Chung Yang, Losi, HPI-Fuelie, Smartech, Nutech and Carson and other engines.The most widely used, qualitatively best spark plug for the model sport! Especially by the most 1/6 scale models the short ceramic body is indispensable, because otherwise on grounds of the heightened mounting position- the spark plug would protrude beyond the roll cage and therefore is extremely fragile by flashovers.Contents:3 pieces
Genuine HT spare/option part. rc-car-online lettering with correspondig logo. All decals are cutted with a plotter. Dimensions:Sheet with car logos: 450 x 160 mmSheet with rc-car-online letterings: 450 x 140 mmContents:1 piece
For converting the Sportsline long touring car into a model with 4WD drive. The conversion kit contains all chassis parts and drive parts that are required for the conversion.
Item N° 67350 Tuning clutch / Zenoah, setComplete clutch with Tuning carrier, lighter clutch blocks, coated dowel screws and reinforced clutch spring. According to the lighter weight the engine speed is slightly higher when the clutch comes, therefore the engine has more power speeding up.
The Wheelbase of the WB535 2WD version is 60 mm longer. This modification improved the directionally stability as well as further driving qualities significantly. In addition parts of the 4WD Monster models were assembled in order to make a conversion to a 4WD model possible with low efforts. According to the large tires this model can be driven almost everywhere. The 26 cm³ Zenoah engine provides sufficient power. Driving fun as well as tremendous looks are the prime characteristics of these models.The body shell comes unpainted, a decal set with writings for further decoration is enclosed in the delivery.You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter: Reflex Wheel Pro III 2,4 GHzReceiver: Mini BECHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery Technical description:The undercarriage of the Monster models is built on a 4 mm angled alloy plate. All borings for fixa- tion of the chassis parts at the bottom side are countersunk in order to prevent the screw heads from sticking out. At the front axle you have the possibility to adjust toe-in or toe-out as well as the wheel camber through track rods with right-hand/left-hand thread. The wheel camber of the rear wheels can be adjusted individually through adjusting screws with right-hand/left-hand thread. Four large-volume oil-pressure shock absorbers are mounted at the lower double wishbones of front and rear axle, these are able to absorb larger shocks of jumps to a great extent and care for an optimal road grip. All rotating drive components are supported by ball bearings. Highly stressed steel parts such as rear gearwheels, differential gears and drive components are hardened. Fuel tank and ra- dio control parts are protected through alloy plates at the sides. The body parts are made of coloured or respectively clear polycarbonate. The Monster tires with tire inserts are glued on chrome-plated rims.The models are equipped with a powerful 26 cm³ combustion engine with ready-for-use oiled air fil- ter. The engine runs with normal 2-stroke petrol-oil mixture (available at every petrol station). The tank filling of 0,7 litres enables you to run your model around 45 minutes. With the installed pull-start system the engine can be started without any difficulties.HT-Edition? HT-Edition means: this version comes with a big set of spare / option parts included. Steel pinions - Non-standard sizesEach of two different ratios are supplied with.Modul: m=1,5Value: 62,60 EURAlloy engine mount smallCNC machined alloy engine mounts, direkt replacement for the stock plastic parts, heat and tweak resistant.Value: 54,90 EURAlloy spur gear carrierUse for 48T - 46 teeth spur gears.Value: 39,90 EURBall bearing set, sealed, set of 15The seal rings on sealed ball bearings keep dirt and dust out of the bearings. They are therefore particularly suitable for use in dirty and dusty environments.Value: 59,90 EURTotal value: 217,30 EURThe pictures may display the car with some optional items which are not included, like bed-mounted rollbar, lights, front bumper or mirrors. These items can be added in the drop down menus.The RTR version is delivered with assembled and preset radio control system and rechargeable batteries. To complete the non-RTR version all popular servos and radio control sys- tems are suitable.Dimensions: Length: 780 mm Width: 510 mm Height: 350 mm Wheelbase: 353 mm
This website uses cookies to ensure the best experience possible. More information.... By clicking on "[Agree / Accept all / etc.]" you also give your consent to the disclosure of your behavior in our store to our partner, shopware AG (Ebbinghoff 10, 48624 Schöppingen, Germany), which cannot assign this data to you personally, but may process it for its own purposes (e.g. product improvements, market behavior analyses).