7855 FG Carburetor type: Walbro WT990
€135.90
Available
Product information "7855 FG Carburetor type: Walbro WT990"
Standard carburetor for Zenoah G290.
Typ: Walbro WT990.
Contents:
- 1 piece
Lebacher Strasse 4
66113 Saarbrücken
Germany
Login
Customers also bought
Genuine HT spare/option part. For all Zenoah G230/240/260/270/290/320 / CY / Fuelie / PTTemperature and dimensionally stable. Thickness: 1,0 mm.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealerContents:1 piece
Especially for installation of all engine gaskets. Temperature resistant from -55 °C to +200 °C. Resistant to water, mineral oils, synthetic lubricants, fuels, organic solvents and refrigerants. info: Hand tight: 10 - 20 minReady to use: 1 - 3 hoursGap fill: 0.5 mmContent: 50 ml Notes for usage: This surface seal is not for use as the sole sealant, it should always be applied in combination with a paper gasket.The HT-surface sealing agent should be sparsely applied over the entire surface, with care being taken that the sealant does not enter the devices internals (e.g. crankcase, differential a.s.o.) during the assembly.
Content: 50 Milliliter (€538.00 / 1000 Milliliter)
Genuine Mielke spare/option part. Contents:1 piece
Customers also viewed
Genuine FG spare/option part.Carburetor type: Walbro WT-813A.Contents:1 piece
Alternative: Walbro 603B also with choke. But with better manufacturing quality!The Walbro WT668B carburetor fits all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23cc up to over 30cc. The Walbro WT668B features an integrated choke with lever and a throttle shaft linkage lever.The WT668B is also available with ball-raced throttle shaft under part number # y0036/04 Ballraced tuning Walbro WT668B carburetory0036/04 Ballraced tuning Walbro WT668B carburetorWith dual ball bearings on the throttle shaft. Two sealed bearings 2RS type (3/16" x 5/16" x 1/8") shielded by two steel plates (5 x 8 x 0.3 mm). High quality processed and optimized for racing use! The soft stock screw holding the throttle lever has been replaced with a high strength Allen key screw. Since all screws on the carb are imperial sized, so is the key for this screw. A corresponding bit is included in our tool set y0785, or you can use Allen key wrench y0037/03 as well.The Walbro WT668B carburetor fits all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23cc up to over 30cc. The modified Walbro WT668B features an integrated choke with lever and a throttle shaft linkage lever.The Walbro WT668B carburetor is also available in a standard version under part number # y1067 Walbro WT668B carburetor.
Genuine FG spare/option part.Standard carburetor for Zenoah G230/260. Carb has integrated choke.Typ: Walbro WT603B.Contents:1 piece
Genuine Mecatech spare/option part. Mecatech Racing carburetor completely CNC machined no tolerances Increase in performance due to less restrictions in the air path, also fuel-saving no failures due to defects Contents:1 piece
Walbro Vergaser WT1107 with choke Standard carburetor for Zenoah G320. Typ: Walbro WT1107This is the stock carburetor used for the G320RC engine, and will also work on all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23 cm³ up to over 30 cm³. Dimensions:Bore: 15,88 mmVenturi: 13,5 mmIndependent tunable high and low speed jets.The carburetor fits all Zenoah, Chung Yang (CY), Losi, HPI und PT (Smartech/Carson) engines from 23 cm³ up to over 30 cm³.
Genuine Zenoah spare/option part. Replacement part fits Zenoah G320RC.
Genuine Walbro spare/option part.Popular performance carburetor without choke; with 13.5 mm venturi diameter, especially suitable for large-displacement engines like the Zenoah G320.The stock throttle shaft has been replaced with the proper version required for car applications; including the throttle lever as well.All existing throttle linkages can therefore be connected as usual without modifications.This carburetor does not feature a primer bulb nor a connection for a return line. It is therefore only connected to the supply line from the tank, the return line of the tank has to be closed.Optional ball bearing of the throttle shaft can be selected from the shops menu.Contents:1 piece