Skip to main content
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

7432/21 FG HT-Nitrited steel pinion for FG, Carson / Smartech street cars - 1 pce

Product information "7432/21 FG HT-Nitrited steel pinion for FG, Carson / Smartech street cars - 1 pce"

HT-Nitrited steel pinion.

Fits for main gear: , .

Fits too for profile regraded pinions: , .

For FG, Carson / Smartech onroad cars.

2 pce threaded screw M5 x 5 are includet.

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Similar products

Average rating of 0 out of 5 stars

7427 FG Plastic gearwheel 40 teeth
Genuine FG spare/option part.Suitable for all 1:5 models.Dimensions:Diameter 63 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5Contents:1 piece

€17.90*

Average rating of 0 out of 5 stars

7433 FG Steel gearwheel hardened 26 teeth - 1pce.
Item N° 7433 Steel gearwheel hardened 26 teeth - 1pce.Suitable for 38 teeth main gear wheel.Diameter 41.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule m=1.5

€29.90*

Average rating of 0 out of 5 stars

7439 FG Alloy gear carrier 52mm - 1pce.
Item N° 7439 Alloy gear carrier 52mm - 1pce.For 44T - 39T spur gears.For 10 mm diameter shafts.

€41.90*

Average rating of 0 out of 5 stars

7439/05 FG Alloy gear carrier 52mm special, 1 pce.
Item N° 7439/05 Alloy gear carrier 52mm special, 1 pce.Precision alloy gear carrier, exact support of the plastic gearwheels 39, 40, 41, 42 and 44 teeth. Very low height design. For 10 mm diameter shafts.Please note: competition layshaft 6041/05 is necessary for installation!

€39.50*

Average rating of 0 out of 5 stars

7474/05 FG Spacer bushing Ø13/10 x 5 mm
Genuine FG spare/option part. This spacer bushing goes into the gear plate between the two clutch bell bearings, preventing them from binding when installing the pinion on the clutch bell.Contents:1 piece

€3.50*

Average rating of 0 out of 5 stars

7432/25 FG Steel gearwheel hardened 25 teeth
Suitable for 39, 40 and 41 teeth main gear wheel.Measures:Diameter: 38,7 mmBore: 10 mmTotal width: 18 mmTooth width: 11,5 mmModule: m=1.5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involute curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn't really matter.Content:1 piece

€35.10*

Average rating of 0 out of 5 stars

7430/24 FG Alloy gearwheel 24 teeth
Genuine FG spare/option part. Extreme light alloy gear wheel in anodizing quality with 24 teeth.Suitable for the gear wheels with 39, 40 and 41 teeth.Dimensions:Diameter: 38,7 mmBore: 10 mmTotal width: 18 mmTooth width: 11,5 mmModule: m=1,5Contents:1 piece

€30.20*

Average rating of 0 out of 5 stars

7458 FG Carrier - 1pce.
Item N° 7458 Carrier - 1pce.Suitable for all 2-speed gears.

€40.95*

Average rating of 0 out of 5 stars

7422 FG Gear wheel protect for 38/40/42 teeth - set
Gearwheel protection in transpartent polycarbonate for all FG 1:5 scale models with the gear wheels 38, 40, 42 teeth. Protects the driving gear wheels almost from dirt, sand and stones. We recommend the mounting when driving on car parks. Not suitable for Formel 1, Leopard 2 + 4 Competition, Competition and Competition Evolution models.

€39.50*

Average rating of 0 out of 5 stars

7427/01 FG Plastic gearwheel 40 teeth 2-speed - 1pce.
Suitable for all 1:5 models with 2-speed gear.Diameter 63 mmWidth 15.5 mmTooth width 12 mmModule: m=1,5

€17.90*

Average rating of 0 out of 5 stars

7431 FG Steel gearwheel hardened 22 teeth - 1pce.
Item N° 7431 Steel gearwheel hardened 22 teeth - 1pce.Suitable for 42 teeth main gear wheel.Diameter 35,7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule m=1.5

€28.50*

Average rating of 0 out of 5 stars

7432 FG Steel gearwheel hardened 24 teeth - 1pce.
Item N° 7432 Steel gearwheel hardened 24 teeth - 1pce.Suitable for 39, 40 and 41 teeth main gear wheel.Diameter 38.7 mmBore 10 mmTotal width 18 mmTooth width 11.5 mmModule m=1.5

€31.90*

Customers also viewed

Average rating of 0 out of 5 stars

HT-Alloy pinions for FG and Carson C5 / R5, 1 pce.
zahn_0003 Size: y19418 - 18/46 coated surface
Hard coated surface for wear protection.Non-standard sizes use two numbers for definition. The second number gives the size of the corresponding ring gear.Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.

€29.90*

Average rating of 0 out of 5 stars

Carburetor Walbro WT 603B with choke, ball-raced
7355/08 Carburetor type: Walbro WT 603BStandard carburetor for Zenoah G230/260. Carb has integrated choke. Typ: Walbro WT603B y0036/01 Ball-raced tuning carburetor Walbro WT 603B-RacingWith dual ball bearings on the throttle shaft. Two sealed bearings 2RS type (3/16" x 5/16" x 1/8") shielded by two steel plates (5 x 8 x 0.3 mm). High quality processed and optimized for racing use! The soft stock screw holding the throttle lever has been replaced with a high strength Allen key screw. Since all screws on the carb are imperial sized, so is the key for this screw. A corresponding bit is included in our tool set y0785, or you can use Allen key wrench y0037/03 as well. Ball-raced Zenoah G230/260 stock carburetor. Fits all Zenoah G230/240/260/270/290/320 engines as well as the respective Chung-Yang (CY) versions, also Losi and HPI Fuelie, Smartech, Carson PT engines, and many others.Normal:Ball-raced:

€88.90*

Average rating of 0 out of 5 stars

F004 Carson Steering Servo 30kg
Genuine Carson spare/option part. DimensionsLenght approx 63mmWidth approx 33mmHeight approx 55mmThe stronger alternative:K-Power DM4000 Servo 54kg-cm/0,11 s/6 Volt till 8,4 volt 89,90 EURHowever, the installation requires some "rework" on the servo mount!Contents:1 piece

€59.90*

Average rating of 0 out of 5 stars

y0188 Alloy engine mount set for Carson/Smartech 2WD Off-Road + Monster models
Genuine HT spare/option part. CNC machined alloy engine mounts, direkt replacement for the stock plastic parts, heat and tweak resistant. They come with all necessary hardware included.Fit Attack / Touareg / Comanche / Firehammer / TravellerContents:2 pieces

€79.90*

Average rating of 0 out of 5 stars

LOS252079 Losi Pinion Gear, 19T, 1.5M, 8 mm Shaft
Genuine Losi spare/option part. Contents:1 piece

€22.89*

Average rating of 0 out of 5 stars

HT-Steel pinions for Carson / Smartech 2WD offroad cars
Genuine rc-car-online spare/option part. The pinions are made from nitrited steel. The do all correspond with the standard main gear and are secured using two grubscrews.These pinions are profile regraded and have all the same diameter!Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.Contents:1 piece

€29.90*

Average rating of 0 out of 5 stars

HT-Nitrited steel pinions for all FG and 1/5 scale Carson / Smartech C5
Non-standard sizes use two numbers for definition. The second number gives the size of the corresponding ring gear.Attention: not suitable for 1/6 scale Smartech / Carson 2WD Off-Road models. (Link to the Carson Smartech pinions: here)Pinions up to 16T can be used on the layshaft as well.Module: m=1,5Profile regraded, this means that the number of teeth is changed while the diameter remained constant. The part of the involutes? curve that defines the tooth profile is changed. Positively regraded (lower number of teeth) pinions are stronger and run smoother, the reduced strength of negatively regraded pinions doesn?t really matter.Teeth:Item no.:13 Teeth HT y026814 Teeth FG 604614 to 48 Teeth HT y011615 to 48 Teeth FG 604715 to 48 Teeth HT y19354 wide16 to 48 Teeth FG 643116 to 48 Teeth FG 6431/1 wide17 to 48 Teeth HT y19355-116 to 46 Teeth HT y011917 to 46 Teeth HT y1935518 to 46 Teeth FG 643219 to 46 Teeth HT y1935718 to 44 Teeth HT y012319 to 44 Teeth FG 6432/220 to 44 Teeth FG 643321 to 44 Teeth HT y1935820 to 42 Teeth HT y090421 to 42 Teeth FG 7431/2122 to 42 Teeth FG 743121 to 40 Teeth FG 7432/2122 to 40 Teeth FG 7432/2223 to 40 Teeth FG 7432/2324 to 40 Teeth FG 743225 to 40 Teeth FG 7432/2526 to 40 Teeth HT y1936426 to 38 Teeth FG 7433Contents:1 piece

€29.90*
Loading...
Upload in progress, please be patient ...
Shopware-Plugin Development Shopware-Theme Development