7315/01 FG Screw for carrier Zenoah

Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³.Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.Content:7315 Clutch block carrier7315/01 Screw for carrier7318 Dowel screw for clutch blocksy1419 Sinter clutchy1419/01 Clutch springs for Sinter clutch

With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.With the new "K & N" version of the Losi DBXL there is another detail, which need to be considered.From the very beginning the hole pattern for the engine installation in the DBXL chassis plate was no precise match to the hole pattern of the engine, even when delivered in stock form with standard engine. Now with the "K&N" version the engine mount has been changed to eliminate this discrepancy. However, all aluminum engine mounts available on the market share their dimensions with the previous plastic engine mount. For the installation of a G320 Zenoah in a "K&N" -DBXL two possible combinations exist in order to obtain the correct hole pattern:When using the standard (new) plastic engine mount a shortened clutch housing is required as in a 5ive-TWhen using an aluminum engine mount a stock length clutch housing is requiredSeparately, it is recommended to enlarge the cutout in the body panel in front of the K & N air filter for about 2 - 3 mm to ensure that the panel cannot chafe on the air filter.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

T-FHSS SR (SUPER RESPONSE) AND TELEMETRY T-FHSS:In addition to the T-FHSS telemetry system, we added a T-FHSS SR (Super Response) system that increased processing speed to further improve response. SR system does not support telemetry function. *R304SB and R304SB-E are not compatible with SR system.T-FHSS MINIZ SYSTEM:By changing to the MINIZ system in the receiver setting menu, you can use Kyosho Mini – Z Evo dedicated receiver RA-42. Dedicated Kyosho receiver RA-42 requires purchase separately.FHSS MINIZ SYSTEM:By changing to the MI-FH system in the receiver setting menu, you can use Kyosho Mini – Z FH FS-RM005 module to connect to non-Evo Mini-z.TELEMETRY SYSTEM:The T4PM+ transmitter has adopted the newly developed bidirectional communication system “T-FHSS”.2.4 GHZ SS RADIO COMMUNICATION SYSTEM:Frequency channel setting is unnecessary: Channel shifting takes place within the 2.4 GHz band automatically. This system minimizes the interference from other 2.4 GHz systems.MODEL MEMORY FOR 40 MODELS:Model names can use up to 10 letters, numbers, and symbols, so that logical names may be used. A model memory with different setups can be created by using the model copy function.4-AXIS JOG BUTTON:The (JOG) button can be operated in 4 directions: up, down, left, and right.ESC-LINK FUNCTION (MC-LINK):This dedicated function allows you set up the Link software so that your T4PM can control variable frequency and other data changes in Futaba speed controllers (ESCs): MC970CR, MC850C, MC851C, MC602C, MC402CR, etc.S.BUS SERVO:This is a special function that allows setting of the parameters of our S.Bus servo whose settings are changed by using PC Link software. In addition to the conventional wired system, it can be set wirelessly in combination with the R334SBS or R334SBS-E.STEERING MIXING:Smooth cornering is possible by independent left and right steering servo setting.BRAKE MIXING FOR LARGE CARS (BRAKE):Brake mixing of the front and rear wheel of 1/5 gas power cars and other large cars can be adjusted independently.GYRO MIXING (GYRO MIX):The sensitivity of Futaba car rate gyros can be adjusted from the T4PM.4WS MIXING FOR CRAWLERS AND OTHER 4WS TYPE (4WS):This function can be used with crawlers and other 4WS type vehicles.DUAL ESCS MIXING FOR CRAWLERS CARS (DUAL ESC):ESCs at the front and rear are controlled independently.CPS-1 MIXING (CPS MIX):LED lighting and flashing control using our CPS-1 channel power switch can be matched to steering and throttle operation by switch only.ANTI-SKID BRAKING SYSTEM (TH A.B.S):This function applies the brakes so that the tires of gas powered cars, etc. do not lose their grip on the road even when braking at corners.THROTTLE ACCELERATION (ACCEL):Gas power cars have a time lag before the clutch and brakes become effective. The throttle acceleration function reduces this time lag.THROTTLE SPEED (SPEED):Sudden trigger operation on a slippery road surface will only cause the tires to spin and the model to not accelerate smoothly. By setting the throttle speed function, operation can be performed smoothly and easily. It also suppresses battery consumption.STEERING SPEED (SPEED):When you sense that the steering servo is too fast, etc., the servo operating speed (direction that suppresses the maximum speed) can be adjusted.RACING TIMER (TIMER):The lap timer can record 100 lap times and total time. The timer can also be started automatically by trigger operation. The race time and audible alarm can be set. Re-/fueling time are indicated by an audible alarm. An up timer is also provided.FUNCTION SELECT SWITCH (SWITCH)/DIAL FUNCTION (TRIM DIAL):This assigns functions to 2 switches and dials (digital trim, digital dial). The step amount and operating direction can also be adjusted. Trim positioning at each model call is unnecessary because all the dials are digital.TRIGGER POSITION CAN BE CHANGED:The position of the throttle trigger can be moved forward and backward.TENSION ADJUSTMENT FUNCTION:The tension of the steering wheel and throttle trigger springs can be adjusted from the outside.MECHANICAL ATL ADJUSTMENT:Make this adjustment when you want to decrease the total travel of the brake (push) side of the throttle trigger.YOUR T4PM-PLUS INCLUDES THE FOLLOWING COMPONENTS:T4PM-Plus TransmitterR304SBS ReceiverDry Battery HolderMini ScrewdriverTRANSMITTER SPECS:T-FHSS SR/T-FHSS/S-FHSS SYSTEM, WHEEL TYPE, 4 CHANNELSCOMMUNICATION METHOD: Bidirectional protocolMAXIMUM OPERATING RANGE: 100m (Except the MINIT system) (Optimum condition)FOR SAFETY: F/S, B-F/S, IDTRANSMITTER FREQUENCY: 2.4GHz bandRF POWER OUTPUT: 100mW EIRPPOWER REQUIREMENT: (Dry Cell Battery) Penlight x 3 (4.5 V)CURRENT DRAIN: 150mA or lessTRANSMISSION ANTENNA: 1/2λ di-poleR304SBS Specs:T-FHSS SRSIZE: 33.9 x 22.3 x 11.3 mmWEIGHT: 7.5gOPERATING VOLTAGE: DC 3.7-7.4VR304SB Specs (optional):T-FHSSSIZE: 35.1 x 23.2 x 8.5mmWEIGHT: 6.6gOPERATING VOLTAGE: DC4.8-7.4VR304SB-E Specs (optional):SIZE: 35.1 x 23.2 x 12.5mmWEIGHT: 7.0gRATED VOLTAGE: DC4.8-7.4VOPERATING VOLTAGE: DC4-8.4VNever use the R304SB-E receiver in GP cars/boats