Product information "7110 Samba Installation kit for 50 mm pipes"
Genuine Samba spare/option part.
Fits Samba F1 Titanium RS5, Samba F1 Titanium FG, Samba 6 Titan, Samba 7, No. FG #7406 FG Steel Side Power and many other tuned pipes with a diameter of 50 mm.
Please check first whether the installed pipe mount has the right height in the car so that the alignment of the tuned pipe to engine is still appropriate.
Contents:
1 set
0 of 0 reviews
Average rating of 0 out of 5 stars
Leave a review!
Share your experiences with other customers.
Login
No reviews found. Share your insights with others.
Throttle/brake servo horn dedicated to Mecatech FW01 and FG Evolution.Suitable for all servos with an output shaft with 25T spline shaft, for example:y2006 Digital Big-Scale Servo D-21HVNearly all Robbe/Futaba servosMega Power servoThunder Tiger DS1015Savöx servosand many more!Content:1 x y0700 Double sided alloy servo horn1 x y0700/01 Single-sided alloy servo horn2 x 1018/05 Spacer bushing 5 x 20 mm for throttle linkage Evo 08/510 (one spacer drilled to 3 mm inner diameter)1 x M3 x 30 mm Screw2 x M3 x 12 mm Nut
Genuine FG spare/option part. Very efficient tank venting also for high fuel temperatures, with each 1 valve for ventilation and aeration. Suitable for all fuel tanks of large scale models.
GPM air filter cover which fits easily over your existing air filter. A fastening band band at the bottom holds the cover in place. Maintenance of the main filter will be significantly reduced, especially in very dusty environments.
Genuine TT spare/option part.Spare part for Killswitch TopTuning 0990 or Dynamite 1240. Also suitable for other projects at your own discretion.2-pole connection cable with silicone insulation and 22 AWG/0.32 mm² cross-section, length approx. 80 mm.Contents:1 piece
Item N° 6545/01 FG gold contact plug-in system 2mm - 10pcs.Reverse battery protected gold contact plug-in system. A further great advantage of our plug-in system is the fixing of a plug on the receiver box or rc-plate with screws. This makes the connection of plug and bush easier.
Genuine FG spare/option part. Heavy gauge teflon tube for connection between exhaust manifold and tuned pipe with da inside diameter from 21 mm and a length from 50 mm.You may have to heat the tube with a cigarette lighter for installation.Contents:1 piece
Exhaust port and carburetor intake cover plates, made of 1 mm aluminum, fits most current 23cc - 30cc rc-car engines.Exhaust port cover:Total: approx. 20 x 45 mmMounting holes (ctr./ctr.): approx. 34 mm carb intake cover:Total: ellipse approx. 28 x 40 mmMounting holes (ctr./ctr.): approx. 31 mm
Genuine FG spare/option part.Carbon fibre supporting brace with fittings and mounting material for the FG Competition, EVO and 1:5 Sportsline models 2WD and 4WD for a lateral fixing of Tuning pipes with a diameter of approx. 50 mm.
Genuine HT spare/option part. Very strong, multiple glas fiber layers, nevertheless very stretchable. Resist maximum temperatures up to 250°C (482°F) from.Needs hose clamps with at least 35 mm inner diameter! Maße:Inside diameter: 22 mm Outside diameter: 30 mmWall thickness: 4 mmLength: 50 mmContents:1 piece
The new TT0900 electric starter is pre-assembled and fits a wide range of models including the Losi 5ive-T, 5ive Mini and DBXL, most FG models, HPI-Baja / Wild Attack series etc. The TT0900 electric starter can be started with the remote control (free channel required!). The new TT0900electric starter has much more power than the previous Electric starter thanks to the brushless motor and higher voltage. The popular Zenoah G320 is no longer a problem. It also no longer uses a one-way bearing, which clearly increases reliability. Also the installation space has been noticeably reduced by the motor and a planetary gearbox.The starter components to be fitted weigh about 666 grams plus the battery.For mounting the starter, the flywheel on the engine is replaced by the version with spring-loaded pawls included in the delivery. The tools required for this, piston stopper and flywheel puller, are also included in the delivery.For the 3rd channel the transmitter should have a switch with two positions (momentary switch preferred) or a controller. An additional channel is required for a remote engine killswitch. A killswitch is included in the scope of delivery, but a real fail-safe module such as TT0990 offers higher safety. A possibly already existing failsafe module can also be used.Due to the splitting of the functions engine start and engine stop on two channels, no more compatibility problems with different remote controls are to be expected, only the availability of free channels matters.A 3S LiPo battery is required as the power source.In the shops options menu, we offer a special battery with a more compact design (5,600 mAh/30C, 110 x 49 x 34 mm) which makes installation usually easier in many cars, as well as a battery with standard dimensions (3,900 mAh/60C, 135 x 45 x 25 mm). Of course, other 3S batteries can also be used at your own discretion, but the load capacity (capacity x C-rate) should be on a similar or higher level.Please note that we cannot ship batteries to countries outside the European Union!Since the starter unit can be mounted vertically or horizontally and the brushless starter motor is very small, almost all air filters and most tuned pipe systems can be used.Notes regarding necessary modifications known to us for mounting the starter depending on the vehicle: FG 4wd onroad Rear r/h plastic body mount, depending on position, slightly modified or relocated FG 2wd onroad horizontal engine No modifications Mecatech FW01 No modifications FG 4wd Buggy sportsline Depending on the body shell, minor trimming is required. FG 2wd Buggy current chassis Depending on the body shell, minor trimming is required. FG 2wd Marder (old chassis) Starter fits without modifications to the chassis plate. However, the body shell has to be cut out a bit more seriously in the area of the starter. A repositioning of the rear r/h body mount is recommended. FG Monster Cut the r/h side panel slightly and add a flat area to the aluminum tube which supports the panel on the engine Losi 5ive-B Depending on the tuned pipe, mount starter with motor on top or on the l/h side. Losi 5ive-B Mount the starter motor on the l/h side, space for the tuned pipe is very tight and must be tested in each individual case. No problems when using the stock muffler box. Losi DBXL Depending on the tuned pipe, mount starter with motor on top or on the l/h side. If the starter motor is to be mounted on the side, one screw of the motor roll cage must be replaced by a CSH screw. Carson C5 Only with Zenoah or CY engine, not with Smartech PT engine (different hole pattern on engine)! Carson C6 With the C6, depending on the body shell, trimming is required. HPI 5B/T Depending on the body shell, minor trimming is required. Carson Wild GP Attack Depending on the body shell, minor trimming is required. The accommodation of the engine killswitch, controller unit and wiring harness must be carried out at your own discretion. User Manual FG 4WD On-Road FG Monster FG 2WD On-Road horizontal engine FG 2WD/4WD Buggy current chassis Losi 5ive-T Losi DBXL FG 2WD Marder (old chassis)
Item N° 7112O-ring for Racing fixing kit, 4 pce.Replacement o-ring for Samba order number: 7110, Installation kit for 50 mm pipes, set Thickness: 2,5 mmDiameter: 45 mm
The Samba 8 titanium gives you a weight saving of 140 grams compared to the steel version. We have tested and optimized the Samba 8 Titan- tuned pipe system for half a year on the engine dyno and an additional three months on various racetracks! The pipe has a new, very strong connection system. This low-maintenance flexible connection between pipe and manifold is secured by four (!) springs, making a failure prone o-ring seal obsolete! Despite of the increased performance fuel consumption remains the same compared to a Samba 7 pipe. The Samba 8 system provides significantly better performance, i.e. the power is optimally available across the engines entire rpm range! Again and again, podium places are achieved at major events through the use of Samba tuned pipe systems.Of course, the Samba 8 tuned pipe system is race legal for racing, with the DMC approval number 10-1504 engraved. The Samba 8 - tuned pipe system comes with an installation kit.Fits: All On-road cars from FGContrastBergonzoniHarmGeniusand many others as wellOriginal statement from Samba: "This new tuned pipe system is the result of the development of the Samba 7 tuned pipe!"
Genuine ATOP spare/option part. Upper front camber rods with guide bushing set and with pivoted steel ball joints right/left thread and locknuts for Losi 5ive-T. Balls with 6 mm hole, adapter bushings for 5 mm screws, shortest distance between mounting points (center/center) 130 mm. Contents:2 pieces
Genuine FG spare/option part. Heavy gauge teflon tube for connection between exhaust manifold and tuned pipe with da inside diameter from 21 mm and a length from 50 mm.You may have to heat the tube with a cigarette lighter for installation.Contents:1 piece