Skip to main content
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

6558 FG Y-cable Futaba

Product information "6558 FG Y-cable Futaba"

The Y-cable is required to drive two servos from a single receiver channel.

Content:
  • 1 piece

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Customers also bought

%

Average rating of 0 out of 5 stars

TT0990 Top Tuning Failsafe with kill switch and status LED for all transmitters
Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

€34.90* €42.90* (18.65% saved)

Average rating of 0 out of 5 stars

7332 FG Silencer gasket for CY / Zenoah / Fuelie / PT
Genuine FG spare/option part.For all Zenoah / CY / Fuelie / PT engines.Applications:Click here!Actual product may be of different color. We have no bearing on this since we are not the manufacturer.Please note:It is recommended to use a gasket sealer with every gasket on an engine. This gives better sealing anda longer lasting gasket. We also recommend:y0804 HT-flange sealer 518 y0994 Marston sealery0807 MD-Sil RTV silicone sealerContents:2 pieces

€4.90*

Average rating of 0 out of 5 stars

y2006 Top Tuning Digital pro servo 40 kg
y2006 Top Tuning Digital pro 40 kg is a digital large scale servo with a very robust metal gears.It offers a lot of power at good speed and has a metal housing with side cooling fins.Its installation dimensions fit directly for FG, Losi, HPI and various other models! Dimensions identical to: Multiplex Rhino - Servo 32 kg FG Mega - Servo ST2605 30 kg Spectrum SPMS904WP 34 kg Spectrum SPMS904HV 18 kg Technical data: Classification: large scale servo Dimensions LxWxH (mm): 59.5 x 29.2 x 55.2 mm Operating voltage: 6 volts / 7.4 volts Torque: (Ncm): 380/400 Speed (sec / 60 °): 0.20 / 0.18 Number of ball bearings: 2 Servo gear: metal gears Seals: 3 (splash-protected) Silicone cable: with universal plug, 300 mm long Weight: 146 grams Brass output shaft 17T spline Content: 1 piece of TopTuning Digital pro servo 40 kg 1 piece double sided servo arm 70 mm total 1 piece of 40 mm single sided servo arm 4 pieces of guide sleeves 4 pieces of rubber grommets 4 pieces of fastening screws

€69.90*

Average rating of 0 out of 5 stars

7111 Samba 7 Connecting set
Genuine Samba spare/option part.Connecting springs for Samba 7 pipes.Dimensions:Length: approx 18 mmWire thickness: 0,8 mmContents:8x Connection springs2x Silicone damperring2x Viton O-Ring 20 x 1,5 mm

€12.90*

Average rating of 0 out of 5 stars

7407 FG CFRP supporting brace for Tuned pipe, set
Genuine FG spare/option part.Carbon fibre supporting brace with fittings and mounting material for the FG Competition, EVO and 1:5 Sportsline models 2WD and 4WD for a lateral fixing of Tuning pipes with a diameter of approx. 50 mm.

€35.10*

Average rating of 0 out of 5 stars

y1209 HT Aluminum front bulkhead A for Carson/Smartech, Reely and FG
Genuine HT spare/option part.With provision to mount a stabilizer bar and replaceable bushings for the hinge pins.Fits Comanche, Attack Evo, CRT 2WD, CPT, C5, R5, FG Sportsline and Smartech Contents:1 piece

€49.90*

Similar products

Average rating of 0 out of 5 stars

6547 FG Receiver cable FG gold contact/Futaba - 1pce.
Receiver cable, ready-made with FG gold contact plug-in system for Futaba plug.total length 20-25cm

€17.90*

Average rating of 0 out of 5 stars

6544/01 FG Charging cable EC8 with gold contacts
Genuine FG spare/option part.Contents:1 piece

€13.90*

Average rating of 0 out of 5 stars

6546/02 FG receiver battery Ni-MH 6V 3600mAh
Genuine FG spare/option part.Measures:Width: 111 mmHeight: 47 mmDepth: 23 mmContents:1 piece

€37.50*

Average rating of 0 out of 5 stars

6540 FG Receiver box
Genuine FG spare/option part. Splash-proofed receiver box for all merchantable small receivers, suitable for all car models 1:12 - 1:5.Dimensions:Length: upper section 92 mm, bottom 69 mmHeight: 48 mmWidth: 38 mmContents:1 piece

€13.90*

Average rating of 0 out of 5 stars

6545 FG gold contact plug-in system 2mm - 2pcs.
Item N° 6545 FG gold contact plug-in system 2mm - 2pcs.Reverse battery protected gold contact plug-in system. A further great advantage of our plug-in system is the fixing of a plug on the receiver box or rc-plate with screws. This makes the connection of plug and bush easier.

€7.90*

Average rating of 0 out of 5 stars

6538/01 Servo arm MPX rhino / Hitec 805
Alloy servo arm made of high-strength alloy material.Length over all 53 mm.Distances bore to center of servo horn: 11.5 / 17.5 / 23.5 mm. Inner holes 2.2 mm, middle and outer ones with M3 thread.Content:1 piece

€19.90*

Average rating of 0 out of 5 stars

6536/01 FG Alloy servo arm JR/Multiplex 23 teeth
Genuine FG spare/option part.Contents:1 piece

€9.90*

Average rating of 0 out of 5 stars

6544 FG Charging cable for receiver battery with FG plug
Genuine FG spare/option part. Polarized and gold plated connector system.Content:1 piece

€17.90*

Average rating of 0 out of 5 stars

6545/01 FG gold contact plug-in system 2mm - 10pcs.
Item N° 6545/01 FG gold contact plug-in system 2mm - 10pcs.Reverse battery protected gold contact plug-in system. A further great advantage of our plug-in system is the fixing of a plug on the receiver box or rc-plate with screws. This makes the connection of plug and bush easier.

€39.90*

Average rating of 0 out of 5 stars

FG 6556 Power Pack 2S 7.4V 6000mAh 60C
Genuine FG spare/option part.High-capacity battery.Dimensions:138 x 45 x 24 mContents:1 piece

€107.95*

Average rating of 0 out of 5 stars

6561/01 FG Hitec Transmitter Aggressor - 1pce.
Ergonomically designed 3 Channel FM Transmitter for RC cars, boats and motor bikes in a modern design, handy and light.- Servo reversing on channel 1+2- 3 LED battery status indicators- Low Battery Alarm- Dual rate steering- Charging Jack- Foam steering wheel

€64.70*

Average rating of 0 out of 5 stars

6547/01 FG Receiver cable FG gold contact/Multiplex - 1pce.
Receiver cable, ready-made with FG gold contact plug-in system for Multiplex plug.total length 20-25cm

€7.10*

Customers also viewed

Average rating of 0 out of 5 stars

y2006 Top Tuning Digital pro servo 40 kg
y2006 Top Tuning Digital pro 40 kg is a digital large scale servo with a very robust metal gears.It offers a lot of power at good speed and has a metal housing with side cooling fins.Its installation dimensions fit directly for FG, Losi, HPI and various other models! Dimensions identical to: Multiplex Rhino - Servo 32 kg FG Mega - Servo ST2605 30 kg Spectrum SPMS904WP 34 kg Spectrum SPMS904HV 18 kg Technical data: Classification: large scale servo Dimensions LxWxH (mm): 59.5 x 29.2 x 55.2 mm Operating voltage: 6 volts / 7.4 volts Torque: (Ncm): 380/400 Speed (sec / 60 °): 0.20 / 0.18 Number of ball bearings: 2 Servo gear: metal gears Seals: 3 (splash-protected) Silicone cable: with universal plug, 300 mm long Weight: 146 grams Brass output shaft 17T spline Content: 1 piece of TopTuning Digital pro servo 40 kg 1 piece double sided servo arm 70 mm total 1 piece of 40 mm single sided servo arm 4 pieces of guide sleeves 4 pieces of rubber grommets 4 pieces of fastening screws

€69.90*

Average rating of 0 out of 5 stars

y0657 Receiver battery packs standard size, NiMh, 4500 mAh
y0657 Connector: y0657/01 Futaba, JR, MPX universal
Genuine HT spare/option part. 5 cells, 6 volt, cell size Sub-C. More applications on request.Dimensions: approx 112 x 46 x 23 mmContents:1 piece

€44.90*

Average rating of 0 out of 5 stars

y1436 SPEED TEC CRANK Ignition-System (CIS)
y1436 Tools: Without tool
New ignition system for RC Car race engines with air baffles, special 62 mm balanced flywheel, modified ignition coil mount and special Löhin tuning ignition (#1361). For Zenoah G230/240/260/270/290/320 und CY / Fuelie / Losi engines.A much smaller and lighter flywheel, in conjunction with the special air baffles, ensures that the engine gets more cooling air then with previously available modified flywheels! The fan from the CIS-ignition with fins on both sides is about 30% lighter (!) than the stock version! Needless to say an engine equipped with such a flywheel revs considerably faster and significantly higher, of course. This in itself is nothing new, because modified flywheels, even though not 30% lighter, are pretty common on modified engines. However, the problem with these modified flywheels is maintaining sufficient cooling for the engine, which is absolutely mandatory for a reliably running engine! The 20% smaller in diameter flywheel is primarily responsible for the very substantial performance increase by the SPEED TEC CRANK ignition . The lower inertia, which is quite crucial for engine performance, allows for an extremely fast and higher revving engine! The air baffles of the CIS-ignition ensure that the path of the cooling air is matched to the reduced diameter of the CIS-fan wheel and the engine gets more cooling! As our product video shows, the stock engine gained near 2,000 rpm through installation of the SPEED TEC CIS-ignition ! But perhaps the optimized torque is even more convincing. This for 30% reduced and 20% more centrally positioned flywheel mass gives your engine a stunning power increase. Other benefits of SPEED TEC CIS - ignition system: Fits all Zenoah, as well as HPI, Losi-, CY 1/5 & 1/6 engines (incl. Zenoah G320) No modifications to the cylinder or the ignition coil mount required! No assembly of the flywheel, thus 100% exact fit and running true The enclosed Löhin ignition system is designed for speeds up to 25,000 rpm! The baffles protect the flywheel from debris (stones, etc.) Complete with Löhin ignition and all necessary parts in a nice special bag Easy installation: Remove the stock ignition system - install the CIS-ignition - done! The color of the ignition cable and the spark plug cap may vary.

€329.00*

Average rating of 0 out of 5 stars

6540 FG Receiver box
Genuine FG spare/option part. Splash-proofed receiver box for all merchantable small receivers, suitable for all car models 1:12 - 1:5.Dimensions:Length: upper section 92 mm, bottom 69 mmHeight: 48 mmWidth: 38 mmContents:1 piece

€13.90*

Average rating of 0 out of 5 stars

5651 Mielke Power Gearshift II Converse clutch for FG Evo / RS5 TC / Harm SX3, 2,4 mm springs, Mix with long clutch carrier
Genuine Mielke spare/option part. Fits FG Evo / RS 5 Tourenwagen / Harm SX 3 / Losi 5ive / Losi DBXL / HPI Baja.Backwards installedshoes make this clutch a "Converse" clutch!After many successes with the "normal" Power Gearshift clutch this is the next step.Made of high-strength aluminium 7075-T6! All components, including the pads, are manufactured on precision machines.Contents:1 piece

€129.50*

Average rating of 0 out of 5 stars

y0730/19 Full-aluminum clutch shoes conversion kit
Genuine GPM spare/option part. Full aluminum clutch shoes are very successfully used in 1/5 onroad racing applications.Therefore we can now offer the GPM conversion kit for BigScale Cross/Race clutches to full-aluminum clutch shoes. Made of a special alloy to suit this application the kit comes with 1.4 mm wire diameter springs and new spring pressure plates.Slight aluminum deposits in the clutch bell and corresponding wear marks in the clutch shoes are normal with the Big Scale ALLOY clutch and have no negative effect on the function. Caution: It is very important that when swapping the full-aluminum clutch shoes against the organic friction pads of a Big Scale CROSS or RACE to use a different or new , because the rough surface of the aluminum deposits in the clutch bell left by the Big Scale ALLOY will cause a high wear on the organic pads.y0730y0731Content:1 set

€54.90*

Average rating of 0 out of 5 stars

y0425/01 Y-harness, silicone insulated, universal/JR
Genuine HT spare/option part. The Y-harness is required for running two servos on a single receiver channel. Top quality heavy gauge 0.5 mm² cable with silicone insulation, 150 mm long, suitable for all rc-systems.Content:1 piece

€12.90*
Loading...
Upload in progress, please be patient ...
Shopware-Agency Shopware-Agency