Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

LOS45004 Losi DBXL 1:5 4WD tyre set, 1 pair mounted

Product information "LOS45004 Losi DBXL 1:5 4WD tyre set, 1 pair mounted"

Produkt Eigenschaften

FahrzeugtypBuggy
FelgenpositionVorne/Hinten
Maßstab1:5
PakettypVormontiert
Reifen Innen / Felgen Aussendurchmesser4.75 Zoll

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Customers also viewed

Average rating of 0 out of 5 stars

B501 Carson Dirt Tire front for Wild GP Attack
Genuine Carson spare/option part. Contents:2 pieces / 1 pair

€69.90*

Average rating of 0 out of 5 stars

LOS252021 Driveshaft rear center Losi DBXL 1/5 4WD
Genuine Losi spare/option part. Replacing the pins on DBXL drive shafts LOS252001, LOS252021, LOS252019: Remove set screw completelyOpen bench vise until the pin just fits between the jaws Position shaft on vice, held by a second person if necessaryDrive pin out with light hammer blows using a pin punch or a suitable comparable tool If Loctite was excessively used in the assembly, heating the shaft end may be required. Depending on the thread locking compound, you will strive for a value of 200 - 300°C. The shaft end must not be annealed! An annealed pin will mushroom on impact and make it very difficult to drive it out if not impossible. When installing the new pin from set LOS252020 make sure that the flat section of the pin is positioned under the set screw. The set screw should be just slightly tightened against the pin using high strength thread locker (link). Firm tightening puts the pin under preload and increases the risk of breakage!

€59.99*
%

Average rating of 0 out of 5 stars

y1420 Diff Locker for Losi 5ive-T/2.0, 5ive-B and Mini
Genuine HT spare/option part. The spool replaces the center differential and keeps the speed of both output shafts the same. As a result, especially the acceleration of the vehicle is significantly increased.The spool is nicely made of high-quality burnished steel and very strong. Its total length is the same as a normal differential housing with gasket. The gasket is no longer used with the spool. The driving pin of the front output shaft is secured by an O-ring. The screws for the connection with the spur gear are secured with nylock nuts. This eliminates the need for waiting for the curing of a thread locking compound and makes the removal of screws with damaged head much less critical.The spool would physically fit front and rear applications as well; however, its use here makes no sense to driving dynamics.Scope of delivery:Spool2 x Driving pin 4 x 20 mmO-ring4 x Steel nylock nut M4

€29.97* €59.95* (50% saved)

Average rating of 0 out of 5 stars

R250 Monster tires, 230 mm, with Kevlar belt reinforcement, incl. rims with 24 mm hex drive (LOSI/HPI)
Genuine UFRC spare/option part. Original equipment tires of the Ghost Rabbit GR1.Fits Losi MTXL as well.When using our special wheel nuts TT1020/02 these tires can also be mounted on the Traxxas X-Maxx.Tire with vulcanized Kevlar belt, speed resistant (no ballooning) and yet flexible.Rim with steel hex insert.Diameter 230 mm, width 100 mm, 24 mm hex wheel drive.Rim thickness at center hole: 8.75 mm.Hex depth: 8 mm.Weight: approx. 2160 grams/pairOn the Losi DBXL running these wheels requires the installation of the DBXL024 ATOP axle extenders!Contents:2 pieces

€149.90*

Average rating of 0 out of 5 stars

y1417/01 GPM - Ultragrip 170x80/x60 mm for Losi and HPI (24 mm hex drive)
y1417_01 Version: Each 1 pair 60 mm and 80 mm tires/inlays/rims+ 25EUR
Ultragrip 170x80 and 170x60 on black MadMax Extreme rims with 20 beadlock screws, with 24 mm hex socket and reinforced silver headlock rings for Losi 5ive-T and Desert Buggy XL as well as all HPI Baja 5 cars.150 shifted long lugs and a central, 4 mm high ridge on the 60 mm wide front tire, and 210 pieces of square 6 x 4 mm studs on the 80 mm wide rear tire ensure optimal propulsion! The flattened profile structure of the rows of knobs reduces the directional control and guarantees an exceptionally good on-center feel! This makes the car less prone to unwanted traction rolls! Due to the extreme load created by the MadMax Ultragrip tires the rim was optimized again with a reinforcement ring.The tires are fitted with a special rigid insert, which can handle the cornering forces and maintain the tires shape even on heavy cars like the Losi 5ive-T.The complete set includes two each 60 mm and 80 mm tires, or two pairs 60 mm tires for Losi 5ive T in a body covered with wheels (like the original body), with inserts and MadMax EXTREME rims! We recommend to check the beadlock screws after the run. Dimensions:Outside diameter: 170 mmFront tire width: 60 mmRear tire width: 80 mmReinforced 24 mm hex wheel drive Set price 2 pairs / 4 pcs. EUR 89,90Regular price EUR 163,40The video shows the 18 mm square drive version. Also available with 24 mm hex. Some off-road tires knowledge can be found here!

Variants from €99.90*
€124.90*

Average rating of 0 out of 5 stars

y0617/01 Offroad Super Combi - Front V-Pin/Rear Mammoth glued on silver rim, 2 pairs/4 pieces
The offroad tire combination!V-Pin front and Mammoth wide tires in rear are the unbeatable combination for offroad use.combi set:Mammoth ready glued: 99,90 EURV-Pin ready glued: 78,80 EURTotal: 178,90 EUROffer price: 99,99 EURDescription for V-Pin tires:The V-pin competition tire is particularly suitable for tracks with loose and sandy surface.The high tread profile, extended to the tire shoulder requires a high manufacturing cost.This tread design guarantees an extremely high side traction and provides maximum propulsion especially on surfaces like sand and loose soil for optimum.By cutting of the tread profile of the V-pin tires you can adjust your car's handling easily. The partly or nearly complete removal of the V-pin tire's tread on the outside of the tire, greatly affects the tire's side bite when cornering.Summarized: removing tread from V-Pin tires on the front axle will reduce oversteering, calm your car and make it easier to drive.When oversteering is extreme (e.g. high grass) you may even start cutting the tread on the inside shoulder. This can prevent your car from those annoying traction rolls.Diameter: 163 mmWidth: 65 mmPrices of the components V-Pin:V-Pin tires EUR 39.90 EUR / pairV-Pin tire inserts EUR 9.90 EUR / pairsilver Rims FG 3105/02 EUR 14.90 EUR / pairglue set y0067 EUR 13.30 EURTotal EUR 78.80 EURDescription for Mammoth tires:Extra wide tire mounted and glued on genuine 1/6 scale FG buggy silver rims 3105/02 with silver extension ring 3106!The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall.Diameter: 165 mmWidth: 80 mmRim with 18 mm square driveThe Mammoth brings, due to its quite strong and large pins and the extreme width of the tire, especially on hard and low grip surfaces a high traction! Where other tires spin helplessly the Mammoth provides serious traction. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.Combination for the HPI Baja and 5T cars will the rim extension rings glued on the inside!Unit prices Mammoth:Mammoth tires extra wide: 47.20 EUR / pairMammoth inserts extra wide: 9.90 EUR / pairgenuine FG wide track rims 3105/02: 14.90 EUR / pairgenuine FG rim extension rings 3106: 14.90 EUR / pairmounting + glueing rims / extensions / inserts / tires: 13.00 EURTotal: 99.90 EURMammoth ready glued: 99,90 EURV-Pin ready glued: 78,80 EURTotal: 178,90 EURIntroductory price: 99,99 EUR

€119.99*
Loading...
Upload in progress, please be patient ...
Shopware-Plugin Development Shopware-Agency