3262/01 FG Vehicle decals set CAT-Truck
€16.10
Available
Product information "3262/01 FG Vehicle decals set CAT-Truck"
Contains the stickers of the headlights, the rear lights and the radiator grill.
Not included are the advertising labels for the original design. Please order separate.
Dimensions:
- 435 x 145 mm
Contents:
- 1 piece
Lebacher Strasse 4
66113 Saarbrücken
Germany
Login
Customers also bought
Hazard and Precautionary StatementsHazard Statements (H-Code)H222Extremely flammable aerosol.H229Pressurized container: may burst if heated.H319Causes serious eye irritation.H336May cause drowsiness or dizziness.Precautionary Statements (P-Code)P210Keep away from heat, hot surface, sparks, open flames and other ignition sources. No smoking.P251Do not pierce or burn, even after use.P305P351P338IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.P337P313IF eye irritation persists: Get medical advice/attention.P403P233Store in a well-ventilated place. Keep container tightly closed.P410P412Protect from sunlight. Do not expose to temperatures exceeding 50°C/122°F.Supplemental hazard information.EUH066Repeated exposure may cause skin dryness or cracking.Farbe:Lexan SprayInhalt:150mlProduct information "RC - Paint Lexan special colors, spraycan (Offer) Buy 3 get 4"For every 3 cans purchased you will get 1 can for free.For example: if you select 4 cans our shop will charge them all when putting in the basket, but deduct one can during the check-out procedure later.RC - Paint is a special paint for lacquering RC-Car Lexan (Polycarbonate) body shells. The ultra-fine mist provides optimal coverage!Through an optimized atomizer valve an outstanding painting result is guaranteed.RC-Paint Lexan color is produced in a particularly environmentally friendly.The composition of colors (color pigments) was placed on the lowest possible heavy metal content and the best possible environmental compatibility of the solvent and propellent gas value.Contents:1 piece / 150 mlThe content of the can is 150ml and suffices - depending on the intensity of the painting, - for one 1/8 or two 1/10 body shells. Two to three cans are needed for a 1/5 or 1/6 body shell.
Hazard and Precautionary StatementsHazard Statements (H-Code)H222Extremely flammable aerosol.H229Pressurized container: may burst if heated.H319Causes serious eye irritation.H336May cause drowsiness or dizziness.Precautionary Statements (P-Code)P210Keep away from heat, hot surface, sparks, open flames and other ignition sources. No smoking.P251Do not pierce or burn, even after use.P305P351P338IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.P337P313IF eye irritation persists: Get medical advice/attention.P403P233Store in a well-ventilated place. Keep container tightly closed.P410P412Protect from sunlight. Do not expose to temperatures exceeding 50°C/122°F.Supplemental hazard information.EUH066Repeated exposure may cause skin dryness or cracking.Farbe:Lexan SprayInhalt:150mlProduct information "RC - Paint Lexan special colors, spraycan (Offer) Buy 3 get 4"For every 3 cans purchased you will get 1 can for free.For example: if you select 4 cans our shop will charge them all when putting in the basket, but deduct one can during the check-out procedure later.RC - Paint is a special paint for lacquering RC-Car Lexan (Polycarbonate) body shells. The ultra-fine mist provides optimal coverage!Through an optimized atomizer valve an outstanding painting result is guaranteed.RC-Paint Lexan color is produced in a particularly environmentally friendly.The composition of colors (color pigments) was placed on the lowest possible heavy metal content and the best possible environmental compatibility of the solvent and propellent gas value.Contents:1 piece / 150 mlThe content of the can is 150ml and suffices - depending on the intensity of the painting, - for one 1/8 or two 1/10 body shells. Two to three cans are needed for a 1/5 or 1/6 body shell.
Genuine HT spare/option part. Decal sheet with logos from several rc-car and supplies manufacturers. All decals are cutted with a plotter. List of manufacturers:rc-car-online.deSmartechLightscaleMecatechHPI-RacingRC-PaintRoadiesFGSpektrumClark´sLosiHorizon HobbySpeed-TecGRPBigscalerGPMPMTZenoahMultiplexLRPChung YangMotulHitecDimensions:220 mm x 330 mmContents:1 piece
Genuine FG spare/option part. Is needed when painting the body to mask the windows.Includes masks for all windows.Contents:1 piece
Customers also viewed
Genuine FG spare/option part. The FG Marder body shell is delivered white and without window gitter or decal set.Dimensions:Length: 580 mmWidth: 240 mmHeight: 205 mmContents:1 piece
y0557 Zenoah G230RC, with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge.y1009 Zenoah G240RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)23 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G230RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% widerContains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y0553 Zenoah G260RC with Walbro WT 603B carburetor (also available in the ball-raced version through the shop's options menu)This is the G260 in the 26 cm³ version.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. y1011 Zenoah G270RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)26 cm³ Zenoah engine for large scale cars!Please note: contrary to their new designation the displacement has not been increased! The outer dimension didn't change, so you don't need any additional parts for the engine swap!The engines feature the following improvements over their G260RC:- Quantity of cylinder mounting bolts increased from 2 to 4- Improved strength of crankcase- Added additional bearing on the PTO (clutch) side of crankshaft- Redesigned shape of cylinder fins- Dimension of air intake port is 5% wider- New carburetor (WT-990) Contains internal fuel pump which increases acceleration from idle to wide open throttle.Removal of choke valve increases performance by increasing air flow to the carburetor - Changed material of the insulator gasket to metal, which improves sealing performanceThe engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter are optionally available at additional charge. 7800 Zenoah G290RC with Walbro WT 990 carburetor (also available in the ball-raced version through the shop's options menu)Same dimensions as the Zenoah G230, G240, G260, G270.New generation Zenoah engine with 28,5ccm cylinder capacity and approx. 3.9 hp. The cylinder is fixed with 4 screws. The technical details are identical to the Zenoah engines G240RC and G270RC.The engine will be delivered with pull starter, carb and spark plug / spark plug cap. Genuine Zenoah air filter and / or complete clutch are optionally available at additional charge. Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.Zenoah G320RC with Walbro WT 1107 carburetor (also available in the ball-raced version through the shop's options menu)With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT 1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise.
Lighter, for weight-reducing reasons manufactured 1.5mm polycarbonate bodyshell. The set includes: 1.5mm F1 bodyshell, body front and side parts 2mm. The body shell is vac-formed from 1,5 mm Lexan.The set is delivered unpainted.Painting tips:
Former: "Cat" Truck. The set contains the front body, the main body, the driver's cab and the body screws.The rear bumper wont be delivered and has to be ordered separate.The set is delivered not painted.Measurements:Length: 770mmWidth: 435mmHeight: 355mmWheelbase: 535mmPainting tips:
New FG Race Truck Body made of clear polycarbonate, not painted. The body consists of two parts. Suitable for FG Sportsline chassis 1:5 2WD and 4WD, 07 and Competition EVO 08 Chassis. Also fits other manufacturers' chassis with a wheelbase of 530mm.Painting tips: