Skip to main content Skip to search Skip to main navigation
EXTRA 20% off Outlet*. Use Code: EXTRA20 at checkout!!
+49 2151 820200 Mon-Fri 9 am - 6 pm, Sa 9 am - 1 pm

305231 Plastic engine mounts, set

Product information "305231 Plastic engine mounts, set"

Genuine Smartech spare/option part.

Especially for Carson C5 onroad cars.

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Customers also bought

Average rating of 0 out of 5 stars

6049/01 FG Clutch bell
Genuine FG spare/option part. New version clutch bell for all FG cars except Formula 1. Contrary to the previous version 6049 the flat areas for the pinion set screws are angled at 90° instead of 180° (see pic).Dimensions:Shaft diameter 10 mmShaft length 38,2 mmOverall length 61 mmAouter diameter bell 58 mmInner diameter bell 56 mmContent:1 pieces

€53.95*

Average rating of 0 out of 5 stars

y0045 GPM Crankcase cover for 1/5 & 1/6
To ensure the required cooling for current 1/5 and 1/6 engines the flywheels have fins on both sides. Therefore the fan housing has large openings on the crankcase side for the required air supply. However, the risk of foreign objects (grass, sand, or even stones!) entering here Is very high! As a result, broken fins on the flywheel occur frequently. This leads to reduced cooling efficiency and - even more critical vibrations from a flywheel which is out of balance due to missing fins. Therefore, this kind of flywheel protection is highly recommended, especially for offroad use. The product video explains the handling in detail! Note:It is essential to thoroughly clean and degrease the crankcase prior to attaching the hook-and-loop tape (OKS2661)!For installation on Chung-Yang and Zenoah engines in FG cars, the crankcase cover must be slightly modified in two places where the engine mount is attached (see Figure 6 and 7). Furthermore the fit of the fabric must be as tight as possible in the region of the layshaft pinion (in front of the differential ring gear!) (see Figure 8).Set includes:Special tailored fabric with sewed on hook-and-loop tapehook-and-loop tape for installation to the crankcaseAdhesive for securing the hook-and-loop tape

€24.90*

Average rating of 0 out of 5 stars

GPM Starter cover, no. BJPSCO
Keeps cool air coming to your engine by keeping dirt and grass from clogging up the pull starter area. Easily wipe off anything not deflected away. Installs on the starter cover with hook & loop tape. With metal cable management.If using a FG monster / stadium model an additional hole for the support of the lateral carrier plate has to be cut out.

€25.60*

Average rating of 0 out of 5 stars

7379/08 FG Choke lever for CY / Zenoah / Fuelie
Genuine FG spare/option part.Contents:1 piece

€4.50*

Similar products

Average rating of 0 out of 5 stars

y0145 Alloy engine mount, small, for Carson C5 / R5 / Smartech Ranger / Reely onroad cars, 1 pce.
CNC machined alloy engine mount, direkt replacement for the stock plastic part, heat and tweak resistant.They come with all necessary hardware included.

€39.90*

Average rating of 0 out of 5 stars

32738/01 Spacer for engine mount
Genuine Carson/Smartech spare-/option part. Fits Carson and Smartech Onroad models. Contents:2 pieces

€2.90*

Average rating of 0 out of 5 stars

y0143 Alloy engine mount, large, for Carson C5 / R5 / Smartech ranger / Reely onroad cars, 1 pce.
CNC machined alloy engine mount, direkt replacement for the stock plastic part, heat and tweak resistant. They come with all necessary hardware included.

€49.90*

Customers also viewed

Average rating of 0 out of 5 stars

7353 FG Rubber gasket
Genuine FG spare/option part.Suitable for FG 7347 and FG 7348.Hint:For installation on a Losi DBXL tank the mounting hole of the DBXL tank must be enlarged to 23 mm diameter.Contents:1 piece

€5.90*

Average rating of 0 out of 5 stars

y0145 Alloy engine mount, small, for Carson C5 / R5 / Smartech Ranger / Reely onroad cars, 1 pce.
CNC machined alloy engine mount, direkt replacement for the stock plastic part, heat and tweak resistant.They come with all necessary hardware included.

€39.90*
%

Average rating of 0 out of 5 stars

y2005 Tuning aluminum engine mount set for all FG 4WD Sportsline cars
Tuning aluminum engine mount set for all FG 4WD Sportsline cars: Monster-Truck, Off-Road Buggy, Marder, Beetle, Touring Cars.Inhalt:Aluminum large engine / layshaft mountAluminum small engine mountAll necessary screws are included!

€99.90* €124.80* (19.95% saved)

Average rating of 0 out of 5 stars

FG Sportsline 2WD-530 with Alfa Romeo 156 body shell, 23cm³ Engine
The Sportsline quality at a reasonable price for beginners. For rookies and all those who simply just want to have fun and drive a DTM Audi, Mercedes or a fast Porsche. The Sportsline series is ideal for car modellers whose main focus is not just the chassis, but rather the combination of chassis and body shell.Technical description:The model has a 535 wheelbase. The models are built on a 4mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in. Further equipment points are front disk brakes, differential gear, easy-running FG ball drive, alloy brake calliper with big brake disk, stabilizer bar front and rear, tuned pipe muffler, Evo gas tank, rear brace, 24T steel pinion, spark plug cap suppression cover, latest version (Evo) oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The models are equipped with a powerful 23ccm combustion engine. The engine needs a 2-stroke petrol oil mixture. One tank filling gives you about 45 minutes driving fun. The power is transmitted over the well-tried system: from the engine over the 2-block clutch over radial tooth wheels on to the rear axle which is equipped with the bevel differential gear with pluggable axles. RC-plate with receiver box.To complete the models all merchantable servos and radio control systems are suitable. The RTR version comes with complete factory installed rc-system, including Ni-Cads!Dimensions: Length: 780 mm Width: 392 mm Height: approx. 240 mm Wheelbase: 530 mm The car comes with an unpainted body shell!Touring cars in action!Painting tips:

€1,149.00*

Average rating of 0 out of 5 stars

y0045 GPM Crankcase cover for 1/5 & 1/6
To ensure the required cooling for current 1/5 and 1/6 engines the flywheels have fins on both sides. Therefore the fan housing has large openings on the crankcase side for the required air supply. However, the risk of foreign objects (grass, sand, or even stones!) entering here Is very high! As a result, broken fins on the flywheel occur frequently. This leads to reduced cooling efficiency and - even more critical vibrations from a flywheel which is out of balance due to missing fins. Therefore, this kind of flywheel protection is highly recommended, especially for offroad use. The product video explains the handling in detail! Note:It is essential to thoroughly clean and degrease the crankcase prior to attaching the hook-and-loop tape (OKS2661)!For installation on Chung-Yang and Zenoah engines in FG cars, the crankcase cover must be slightly modified in two places where the engine mount is attached (see Figure 6 and 7). Furthermore the fit of the fabric must be as tight as possible in the region of the layshaft pinion (in front of the differential ring gear!) (see Figure 8).Set includes:Special tailored fabric with sewed on hook-and-loop tapehook-and-loop tape for installation to the crankcaseAdhesive for securing the hook-and-loop tape

€24.90*

Average rating of 0 out of 5 stars

y1016 Zenoah G320RC with Walbro carburetor WT1107
With 32 cm³ and 30% more power than the Zenoah G290.Significantly more torque and higher stamina due to larger sized bearings all around, with Racing Carburetor Walbro WT1107.The motor is supplied with WT-1107 carburetor and spark plug.SpecificationType: Two stroke gasoline engineDisplacement: 31,8 cm³Bore: 38 mmStroke: 28 mmWeight: 2,3 KgOverall Dimension:Length: 167 mmWidth: 215 mmHeight: 196 mmMaximum Output: 4,6 PSMaximum Torque: 2,00 N-mRotation Direction: CounterclockwiseCarburetor: Walbro WT-1107Spark plug: CMR7HStarting: Recoil starterFor all HPI Baja 5 cars the G320RCer clutch housing has to be shortened at the mounting base, for Losi 5ive- T and Desert Buggy XL cars the clutch housings overall length must be shortened to CY size.With the new "K & N" version of the Losi DBXL there is another detail, which need to be considered.From the very beginning the hole pattern for the engine installation in the DBXL chassis plate was no precise match to the hole pattern of the engine, even when delivered in stock form with standard engine. Now with the "K&N" version the engine mount has been changed to eliminate this discrepancy. However, all aluminum engine mounts available on the market share their dimensions with the previous plastic engine mount. For the installation of a G320 Zenoah in a "K&N" -DBXL two possible combinations exist in order to obtain the correct hole pattern:When using the standard (new) plastic engine mount a shortened clutch housing is required as in a 5ive-TWhen using an aluminum engine mount a stock length clutch housing is requiredSeparately, it is recommended to enlarge the cutout in the body panel in front of the K & N air filter for about 2 - 3 mm to ensure that the panel cannot chafe on the air filter.When installing the air filter you must pay attention to the length of the screws.For use on Losi and HPI we recommend M5x45 screws (like H94763); you can also cut existing screws to length, of course.When ordering with a modified clutch housing we will include these screws!In our shop you can select from Zenoah G320RC engines already modified to fit your HPI or Losi car.The installation of the Zenoah G320RC in other cars (like FG or Smartech buggies / monsters a.s.o.) is not even remotely straightforward, since the layshaft pinion (the small pinion in front of the big differential spur gear) is in the way for the larger Zenoah G320RC crankcase.Compatibility Zenoah / Losi 5ive-T:Please note that for installation in a Losi 5ive the fan cover must be swapped for a Losi or CY cover #5341 in order to fit the chassis" bolt pattern.If you want to install a Zenoah engine into the Losi 5ive, you usually have to use a fan cover from the CY engine.However, there is a workaround to maintain Zenoah fan cover.The adjustment is done via the pinion specific mounting plates for the engine. The change always affects only the rear, outer (carburetor side) plate under the fan cover. This is rotated by 180°; so that the embossed number on this plate faces the exhaust side of the engine!18T pinion: use 20T plate, rotated 180°19T pinion: use 19T plate, rotated 180°20T pinion: use 18T plate, rotated 180°On the plus side you gain the opportunity to easily mount a Zenoah engine keeping the original fan cover. On the other hand there will be the disadvantage of the necessity to combine two different sets of engine mounting plates when installing any pinion other than the stock 19T version. Therefore we do not recommend this workaround for everyday use. Nevertheless it works perfectly should ever the need arise. Attention! We recommend to run exclusively fully synthetic 2-stroke engine oil, like y0813 Motul 800 racing oil.

€319.90*

Average rating of 0 out of 5 stars

6485/01 FG Alloy engine mount small for 1:6/CY / Zenoah alloy - 1pce.
Item N° 6485/01 Alloy engine mount small for 1:6/CY / Zenoah alloy - 1pce.Small alloy engine mount suitable for FG 2WD and 4WD 1/6 cars and Porsche 4WD with CY / Zenoah G230/240/260/270 engine.

€43.90*
Loading...
Upload in progress, please be patient ...
Shopware-Theme Development Shopware-Plugin Development