305158, Shocks repair kit Gas Devil
€19.95
% Regular price: €39.90 (50% saved)
Available
Product information "305158, Shocks repair kit Gas Devil"
Login
Customers also bought
Genuine Champion spare/option part.OEM spark plug for Zenoah G230/240/260/270/290/320.Ideal too for PT, Chung Yang, Losi, HPI-Fuelie, Smartech, Nutech and Carson and other engines.The most widely used, qualitatively best spark plug for the model sport! Especially by the most 1/6 scale models the short ceramic body is indispensable, because otherwise on grounds of the heightened mounting position- the spark plug would protrude beyond the roll cage and therefore is extremely fragile by flashovers.Contents:3 pieces
Mammoth Supergrip onroad 60 and 80 mm tires on white FG rims complete glued, 1 pair.Mammoth Supergrip onroad tires on FG rims for 1/6 and 1/5 offroad cars.Suitable for asphalt surfaces such as car parks and race tracks. Racing tyres for your off-road model.VersionWidthOuter diameterFront64 mm153 mmRear78 mm153 mmGlued on genuine FG rims (rear tires using extension rings outside ), with foam rubber inserts included. Rim has 18 mm square drive with reinforcement ring.Please note: based on experience we recommend against using other manufacturers rims and extensions. Since the Mammoth tires provide very good grip the rim and the bonding must withstand high loads. Due to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable.The Mammoth Supergrip is available in in the following compounds: Super softSoftMediumHardFront tirey0581y0582y0583y0584Rear tirey0591y0592y0593y0594General recommendation:The dirtier the track or the lower the ambient temperatures, the stickier (softer) the rear tires should be.Hint regarding the front tires: 2WD cars should use them one or two grades harder then the rears. 4WD cars usually like the same compound all around.Of course, the softer the tire the higher the wear rate; and this applies to Mammoth Supergrip onroad tires as well.The tires have a special onroad thread pattern but will still provide ideal traction after the pattern has been worn out. The white lettering on the tires has been applied for presentation purpose only. The tires will be delivered with black sidewall.Prices per unit: FrontRearMammoth Supergrip:Pair44,90 EUR49,90 EURTire inserts:Pair13,00 EUR13,00 EURFG rim:Pair14,90 EUR14,90 EURFG extension ring:Pair--.-- EUR14,90 EURMounting:Pair13,00 EUR13,00 EURPrices Total 85,80 EUR 105,70 EUR
Fully painted body with decal set applied. The body also fits the Carson Comanche, Carson Stadium Racer, Stadium Truck, Bigfoot Race and Pickup Truck. With a bit of customisation, it will of course fit almost all 1:6 and many 1:8 RC cars! Unfortunately, the decals are not particularly durable and are partly damaged. However, this has been taken into account in the pricing, given that this is a fully painted, affordable 1:6 body. Measures:Wheelbase: 400 mmWith between the wheels: approx. 255 mmWith in the middle: approx. 235 mmWidth: ca. 250 mmTotal length: ca. 630 mmHeight: ca. 180 mm
Genuine FG spare/option part. Suitable for all mechanical disk brakes.Steel insert provides a strong thread for the mounting bolts.Contents:2 pieces
Customers also viewed
Highlights News 2026 Tuning aluminium lower wishbones, one-piece (front and rear) FG hydraulic brakes front and rearTuning chassis plate black anodised and milled Tuning milled aluminium rear axle linkage for toe-in adjustment Perforated tuning clutch bell Side flaps on the rear spoiler in carbon fibre Highlights Formel 1 Competition- This model is fitted with numerous aluminium parts: - front and rear side bulkheads, rockers, engine mount, suspension arm ends...Steel made Uniball sockets all possible enable all adjustments of the front and rear suspensions.The transmission made with a gearwheell drive offers outstanding reliability and smooth operation.Technical description of the FG Formula 1 Competition :The undercarriage of the FG Formula 1 Competition is built on an 5mm alloy chassis. All screws at the bottom of the chassis are countersunk.Front and rear axle mounts as well as the engine unit are connected over the complete length of the chassis, therefore we achieved almost the stiffness of a monocoque chassis. The quick fix system of the engine makes a fast changing of the engine possible. The drive to the rear axle is carried out over several easy-running front gearwheels and an FG ball drive at the rear axle. A separate flange bearing holds the clutch bell in order to relieve the crankshaft. Front and rear axle with their various adjusting possibilities as king pin angle, castor a.s.o. consist of alloy delta wishbones below. Solid alloy rear axle plates reduce the wear at the rear axle and give an enormous driving stability. 4 oil-pressure shock absorbers controlled by a pushrod suspension as well as stabilizers guarantee an optimal ground contact.We deliver the chassis selectively with FG hydraulic brakes for front or respectively rear axle. The model is powered by a high-capacity 26 cm³ engine with airbox and Tuning pipe.Equipment of the FG Formula 1 Competition CNC-cut 5mm alloy chassis with lateral carbon fiber inserts, 26 cm³ Zenoah engine, inlet silencer, Tuning pipe, FG gearwheel drive, ball drive, complete rear and front axle carrier unit with integrated engine quick-fixing device, double alloy wishbone fastenings, lower alloy delta wishbones at front and rear axle, front and rear alloy uprights, ball-bearing servo saver, steering stops, pushrods, 4 oil-pressure shock absorbers with alloy damper pistons, FG hydraulic brakes at front and rear, stabilizer for front and rear axle, 10mm alloy balls, rear spoiler, polycarbonate body shell, polyamide front spoiler, receiver box, competition tires with tire inserts.For the final assembly of the models you need further: radio control system (transmitter, receiver), 1 large steering servos, 2 servo for throttle brake, batteries and charger.These parts are not included and must be supplied or ordered separately when the rc installation option is selected! Includet Zenoah 26cc engineAirboxPipe Clear bodyshell and polycarbonate spoiler FG hydraulik brakes front and rearDimensions Length: 960mm Width: 440mm Height: 230mm Wheelbase: 620mm Formular 1 models in action!
Part is delivered in silver or black color from vendor!
Alloy rear uprights, with replaceable hinge pin bushings.Fits FG and Carson/Smartech Attack, Attack Evo, Gas Blaster, Gas Devil, Super Attack, CRT, CRT 4x4, CPT, Uno, Monster Truck, Pick Up, Beetle and C5.The bearing bushings and bearings should be glued in place, as they have minimal play.One each lefthand and righthand version.Please note: for the installation of all popular disc brakes, we recommend: y6479
Normal price: 249,90 EUR Tuning front disk brake system for the HPI Baja 5B/SS/5T/5sc, the conversion kit includes all necessary parts. The brake includes the finest parts available for a cable brake and has the following features: * uses existing mounting points for all parts * brake pads and 70 mm diameter stainless rotors made by RS-5, the best performing combination available * hardened stud bolts for the brake pads * billet brake levers, no tweak and best transfer of servo power * ultraflex bowden cables * brake cams run in hardened steel bushings and brass guide plates (miniature bearings don't last in offroad cars) * billet alloy bowden cable support block with adjustment screws * billet alloy bowden cable mounts at the calipers * pre-assembledOn a 5T the stud bolts which hold the brake pads will interfere with the ribs in the rim. However, modifying the rim or swapping the stud bolts for long csh screws allows for installation on a 5T.Spare parts for this brake as a PDF-file with spare part numbersWe highly recommend the installation of a stronger throttle servo to take full advantage of this brake system. The is an excellent choice.
Suitable for all FG/Carson/Smartech cars except FG Evo and Carson 4WD.Please note that tank mount 7143 is required for installation. Installation in a Carson/Smartech 1/6 off-road car requires drilling of two new 4.5 mm diameter holes into the chassis plate. Drilling template is included.Comes as shown with fuel lines, grommet and gas cap included.