2018/01 HPI Receiver battery pack "Hump" 6V / 4500 mAh Ni-MH

Genuine Ansmann spare/option part. With AMP charging jack. Five cells, 6 volt, cell size Sub-C.Suitable for all HPI 1/5 scale models.Dimensions:69 x 51 x 42 mmContents:1 pieceUniversalBEC

Genuine HPI spare/option part. Color: Gunmetal.Contents:2 pieces

Sintered steel clutch for Zenoah and many other rc-car engines from 23 cm³ to 32 cm³.Note: The sintered steel clutch needs a break in period of at least half an hour run time after their first installation. Only then the clutch surface reaches the desired grip and provides the necessary friction. After that the clutch will show consistent operation and extremely low wear!With 80 grams the weight of the clutch is about the same as the usual OEM clutches.As with all non-adjustable clutches a periodic monitoring of the clutch spring is recommended. By changing the spring, it is also possible to match your car to the track conditions, i.e.: the harder the spring, the higher the stall speed of the clutch.Content:5315 Clutch block carrier5315/01 Screw for carrier7318 Dowel screw for clutch blocksy1419 Sinter clutchy1419/01 Clutch springs for Sinter clutch

Genuine FG spare/option part. Practical 220V charger, specially designed for RC cars. The TX/PACK CHARGER 2 enables the charging of a 7.2V drive battery or the transmitter battery.Two outputs: 11.6 V 180 mA (transmitter charging plug) and 7.2 V 180 mA (drive battery with Tamiya plug). Only use one output at a time!Contents:1 piece

Genuine TT spare/option part.The new and improved failsafe modul.This kill switch module works with most FM and 2.4 GHz rc-systems. Not compatible with AVC-equipped receivers! You must have a free channel on your rc-system in order to install the module! This means at least a 3-channel radio for standard 1-servo brake/throttle setups or a 4-channel radio for dual brake servos driven by the radio's mixer function. With this module you can stop the engine with your radio. Additionally the module features a failsafe function which stops the engine when the rx-battery's voltage drops below a certain level or the rc-system has a glitch. A kill switch module fulfils two tasks. On the one hand, as a safety device, it is intended to shut off an engine with magneto ignition in case of failure of the remote control, and on the other hand, the engine can be stopped at any time by remote control.While the latter is mainly used for convenience, the safety aspect is what really matters.The failsave circuit integrated in all modern remote controls may brake the vehicle in the event of a radio interference, but this feature is dependent on the basic functionality of the receiver system and its power supply. However, if the receiver, the gas servo or the power supply fails completely, the failsave of the remote control can no longer do its job. The vehicle may be running haywire at full throttle.In these cases, the kill switch will cut the ignition of the engine and the vehicle will roll out without power.Features:Ready to install no soldering requiredRemote LED for easy-to-spot operational status (ignition live/killed)Optically coupled to isolate the ignition from the radio systemThreshold value for undervoltage protection (4V, 5V, 6V) adjustable with jumpers allows adaptation to the rx-battery type (LiPo, LiFePo, NiMH, NiCd)Contents:1 piece

Genuine HPI spare/option part. Special 3-piece bead lock wheels for the Baja 5B. A beadlock ring (not included) is bolted onto the wheel to securely hold the tyre in place. No glue is used to mount the tyres, which makes changing the tyres a simple task! Also, the wheels can be used again with new tyres.Made from tough, high-impact nylon for extra toughness, the popular HPI Super Star design is available in a wide variety of colours, with the opportunity to further customize the colour scheme further with a variety of bead lock rings! All wheels and bead lock rings are sold to fit front or rear pairs of tyres.Content:2 pieces / 1 pair

Genuine Dynamite spare/option part.Key Features:Kills your 2-cycle gas engine on command, loss of radio signal, low battery, or total battery power lossComes ready to install no soldering requiredOptically Coupled to isolate your ignition system from your radio systemBuilt-in LED for easy-to-spot operational status3-Channel Radio System RequiredNot Compatible with AVC-Equipped ReceiversContents:1 piece