1000-15 Mecatech Brake lever guide block

Replacement part for Mecatech twin piston hydraulic brake.

Mecatech twin piston hydraulic brakeFront Twin piston hydraulic brakes with Epoxi rotors and steel brake pads for optimized braking performance. The master cylinders feature a volume compensation.Fits FG Evo 04 - 08, Mecatech FW01, Competition 07 - 08, Sportsline 08 and with pedestal in every FG offroad cars (buggy / monster / stadium with original FG 700 ml fuel tank).The brake fits without any further accessories on FG Evo-models which are equipped with the a-arms no. 1100/10 respectively 1100/11When running wheel squares with Seeger ring, the ring has to be removed.On FG Evo-models which are equipped with the a-arms no. 1100/05 respectively 1100/06, the brake has to be filled before the installation. In addition the ventilation nipple of the brake must be exchanged against the venting valve no. y0309Pedestal for installation for all FG Offroad-models: Mecatech twin piston hydraulic brake

We have tested and optimized the Samba 8 tuned pipe system for half a year on the engine dyno and an additional three months on various racetracks! The pipe has a new, very strong connection system. This low-maintenance flexible connection between pipe and manifold is secured by four (!) springsDespite of the increased performance fuel consumption remains the same compared to a Samba 7 pipe. The Samba 8 system provides significantly better performance, i.e. the power is optimally available across the engines entire rpm range! Again and again, podium places are achieved at major events through the use of Samba tuned pipe systems.Of course, the Samba 8 tuned pipe system is race legal for racing, with the DMC approval number 10-1504 engraved. The Samba 8 - tuned pipe system comes with an installation kit. The mounting pictures shows the Samba 8 in Titan version.Original statement from Samba: "This new tuned pipe system is the result of the development of the Samba 7 tuned pipe!"

Replacement part for Mecatech twin piston hydraulic brake.

Genuine Mecatech spare/option part. Full-metal hydraulic brake (like the former hydraulic FG brake).Only suitable for models with 18 mm square mount.The set consists of two complete brake calipers for right and left, and 2 brake units, hydraulic oil and all accessories (see also our pictures) required for installation.One version fits front and rearFits onroad / offroad / monster and stadium cars from FG and othersNo need for alloy uprights!Fits Formular 1 models, Competition, Sportsline Also suitable for electric models, but in conjunction with aluminum axle y0932 Bleeding instructionsPlease enquire whether this brake is suitable for your model. Dimensions master brake cylinder:Height: 75 mmWidth: 48 mmDepth: 13 mmContents:1 set

Highlights News 2026 Tuning aluminium lower wishbones, one-piece (front and rear) FG hydraulic brakes front and rearTuning chassis plate black anodised and milled Tuning milled aluminium rear axle linkage for toe-in adjustment  Perforated tuning clutch bell Side flaps on the rear spoiler in carbon fibre Highlights Formel 1 Competition- This model is fitted with numerous aluminium parts: - front and rear side bulkheads, rockers, engine mount, suspension arm ends...Steel made Uniball sockets all possible enable all adjustments of the front and rear suspensions.The transmission made with a gearwheell drive offers outstanding reliability and smooth operation.Technical description of the FG Formula 1 Competition :The undercarriage of the FG Formula 1 Competition is built on an 5mm alloy chassis. All screws at the bottom of the chassis are countersunk.Front and rear axle mounts as well as the engine unit are connected over the complete length of the chassis, therefore we achieved almost the stiffness of a monocoque chassis. The quick fix system of the engine makes a fast changing of the engine possible. The drive to the rear axle is carried out over several easy-running front gearwheels and an FG ball drive at the rear axle. A separate flange bearing holds the clutch bell in order to relieve the crankshaft. Front and rear axle with their various adjusting possibilities as king pin angle, castor a.s.o. consist of alloy delta wishbones below. Solid alloy rear axle plates reduce the wear at the rear axle and give an enormous driving stability. 4 oil-pressure shock absorbers controlled by a pushrod suspension as well as stabilizers guarantee an optimal ground contact.We deliver the chassis selectively with FG hydraulic brakes for front or respectively rear axle. The model is powered by a high-capacity 26 cm³ engine with airbox and Tuning pipe.Equipment of the FG Formula 1 Competition CNC-cut 5mm alloy chassis with lateral carbon fiber inserts, 26 cm³ Zenoah engine, inlet silencer, Tuning pipe, FG gearwheel drive, ball drive, complete rear and front axle carrier unit with integrated engine quick-fixing device, double alloy wishbone fastenings, lower alloy delta wishbones at front and rear axle, front and rear alloy uprights, ball-bearing servo saver, steering stops, pushrods, 4 oil-pressure shock absorbers with alloy damper pistons, FG hydraulic brakes at front and rear, stabilizer for front and rear axle, 10mm alloy balls, rear spoiler, polycarbonate body shell, polyamide front spoiler, receiver box, competition tires with tire inserts.For the final assembly of the models you need further: radio control system (transmitter, receiver), 1 large steering servos, 2 servo for throttle brake, batteries and charger.These parts are not included and must be supplied or ordered separately when the rc installation option is selected! Includet Zenoah 26cc engineAirboxPipe Clear bodyshell and polycarbonate spoiler FG hydraulik brakes front and rearDimensions Length: 960mm Width: 440mm Height: 230mm Wheelbase: 620mm Formular 1 models in action!