y171 Zenoah Pase Tuning engine G260RC 23ccm, used
Product information "y171 Zenoah Pase Tuning engine G260RC 23ccm, used"
Refurbished and tested 260cc Pase Tuning Zenoah engine, sold as used.
It has been fitted with new seals in our workshop, and has been test run and adjusted.
It has a tuning isolator, the compression has been increased, the timing has been adjusted, the piston has been machined, and the channels have been adjusted and enlarged.
The WT990 carburettor is as good as new and has no choke valve.
Please refer to the photos for the condition and scope of delivery.
1 piece
Login
Customers also viewed
Tuning Zenoah 23cc 2-bolt engine, used.Tuning Zenoah 23cc engine with anodized engine housing. This engine has been extensively tuned; the housing, piston, and cylinder have been machined. The flow channels have been enlarged, the timing adjusted, and the compression increased. The engine has been tested in our workshop, the seals have been replaced, and the engine has been test run. See photos for condition and scope of delivery. 1 piece
High-performance steel tuning resonance pipe with a great look and superb workmanship, used. Like-new condition with no dents. The manifold is not original. Suitable for 2WD on-road models, scale 1:5, with horizontal motor and 510 and 530 wheelbase. See photos for scope of delivery and condition. 1 piece
The 2WD-465 Sportsline model is built on the short chassis with double a-arms suspension front and rear. The vehicle is equippedwith the 2-shocks front suspension as standard, which ensures optimum traction for both front wheels.On the GT2, the front axle has been widened to 384 mm. The rear axle is 395 mm wide.Technical description:The model has a 465 wheelbase. The models are built on a 4mm alloy chassis with double wishbones at front and rear axle. All borings of the alloy chassis are countersunk to prevent the screw heads from bearing out. The models are serial equipped with the 2-damper front axle which guarantees an optimal traction of both front wheels. At the front/rear axle you can adjust through track rods or adjusting screws with right-/left-handed thread the king pin angle, trailing effect and toe-in. Further equipment points are front disk brakes, differential gear, easy-running FG ball drive, alloy brake calliper with big brake disk, stabilizer bar front and rear, tuned pipe muffler, rear brace, 24T steel pinion, spark plug cap suppression cover, latest version (Evo) oil-pressure shock absorbers with volume control and external adjusting ring for the initial spring preload. All rotating parts as shafts, axles and clutch bells a.s.o. are supported by ball bearings. You can select the car with complete RTR-equipment from the options menu. RTR-equipment RTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed. Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-battery The models are equipped with a powerful 23ccm combustion engine. The engine needs a 2-stroke petrol oil mixture. One tank filling gives you about 45 minutes driving fun. The power is transmitted over the well-tried system: from the engine over the 2-block clutch over radial tooth wheels on to the rear axle which is equipped with the bevel differential gear with pluggable axles. RC-plate with receiver box.To complete the models all merchantable servos and radio control systems are suitable. The RTR version comes with complete factory installed rc-system, including Ni-Cads! The car comes with an unpainted body shell.The FG 5164 decor sheet is not included!Also available painted in the shop selection!Dimensions: Length: 840 mm Width: 395 mm Height: 250 mm Wheelbase: 465 mm Touring cars in action!Painting tips:
Now, the legendary 1:6 FG Marder 2WD off-road buggy with Stadium tyres! Looks great and offers better handling characteristics. Thanks to the stadium tyres, the Marder is almost 100 mm wider and therefore much higher cornering speeds are possible.
These tyres can also be driven on asphalt.
Dimensions of the stadium wheels: Diameter 170 mm Width 90 mm Mounting square 18 mm
For many years the ideal entry into the elite class of radio controlled cars! The large-scale car with tough 26 cc engine is operated with normal 2-stroke gas.A 800 cc tank gives almost an hour of driving fun!For the FG Stadium Marder theres a wealth of option parts, most of them are not exactly a must, but make infinitely more fun!The FG Stadium Marder is also available with completely installed remote control. Just fuel up, start the engine and drive off.You can select the car with complete RTR-equipment from the options menu.RTR-equipmentRTR = Ready to Run. The RTR version comes ready to use with the 2,4 GHz rc-system already installed.Transmitter 2,4 GHzReceiverHigh power servo for throttle and brakeLargescale servo for steeringTx-battery, rx-batteryFeatures:The model is built on an angled 4 mm chassis plate. All screws on the bottom are countersunk with no protruding heads. Double a-arms front and rear axle with 4 high volume oil-filled shock absorbers ensure optimum traction.All rotating parts are supported by ball bearings. Secondary spur gears, bevel gears inside the differential and all drivetrain parts are case-hardened. Rocker panels protect the car against contamination from below. The model is equipped with a powerful 26 cc engine. It needs a regular 2-stroke petrol/oil mix (available at every gas station). The integrated pull starter allows for easy engine starts without additional equipment.Dimensions:Length: 710 mmWidth: 510 mmHeight: 270 mmWheelbase: 475 mmDrive:2WDMotorization:GasRTR:RTR to chooseScale:1/6
You can select the tyre hardness above: - Hurrax HX100 extreme Grip Medium 175/70 mm tyre
and - Hurrax HX400 extreme Grip Soft 175/70 mm tyre HURRAX extreme is one of the most successful tire in large scale off-road racing and specifically designed for astro turf and solid ground. With more than 700 (!) differently designed, closely spaced lugs and the 70 mm wide tread it is reasonably wear resistant and provides optimal grip with good side traction. If this - i.e. on the front axle - is not desired, you may cut the lugs at the tires outer edge to reduce cornering grip. This can be easily done with a small side cutter or strong nail scissors. In order to reduce the edging in the tire on the front axle.This makes a tire less aggressive during cornering and changes the cars behavior towards understeer. It becomes depending on the track conditions (i.e. wet!) a lot more drivable.An optimal vehicle setup can often be achieved by running already used HURRAX extreme tires on the front and new ones on the rear axle.This is especially true for 2WD models. Dimensions:External diameter approx. 175 mmInner diameter approx. 130 mmWidth approx. 70 mmWeight: one glued tire on Hurrax rim: 470 gramsDue to the high torque load on the bonding of tires on largescale cars, checking the bonding from time to time and re-glueing (y0067) if necessary is unavoidable. GRP off-road disc rim for tires with approx, 132 mm inner diameter.The closed disc rim features reinforcement ribs on the backside and a protective collar around the wheel nut seat.Dimensions:for tires with an inner diameter of approx. 132 mm and approx. 70 mm widthand an outer diameter of approx. 180 mm (like i.e. GRP / Gandini tires)Weight approx. 172 gramms
Genuine FG spare/option part. Newly developed tuned pipe made of strong steel sheet, with plug connecting system. The pipe mounts close to the car for best protection possible and versatile usability. Suitable for:FG 2WD and 4WD 1:6 Off-RoadSmartech 2WD off-road And for many other brand's 1/6 carsNot suitable for:FG Leopard2 2+4 WD Sportsline and CompetitionOn several pictures the pipe is shown with a silicone tube tailpipe extension, which is not included. It can be ordered separately as an accessory with part number 6299/03 or y0995.Content:1 piece